Top 2 flute End Mills

YG-1 E5065 Carbide Square Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 4\ Overall Length, 0.1875\ Cutting Diameter, 0.1875\ Shank Diameter

  • Suitable for general-purpose machining on hardened and high-alloy steel, steel casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic.
  • Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills.
  • Four flutes produce a better finish than fewer flutes.
  • Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
  • Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials.
Check Stock

YG-1 - 55901 E5065 Carbide Square Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 6\ Overall Length, 0.25\ Cutting Diameter, 0.25\ Shank Diameter

  • Suitable for general-purpose machining on hardened and high-alloy steel, steel casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic.
  • Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills.
  • Four flutes produce a better finish than fewer flutes.
  • Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
  • Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials.
Check Stock

Genmitsu 40pcs End Mills CNC Router Bits, 1/8\ Shank CNC Cutter Milling Carving Bit Set Including 2-Flute Flat Nose & Ball Nose End Mill, Nano Blue Coat & Titanium Coat CNC Bits, MC40A

  • ...gsten carbide steel alloy that can keep continuous machining 800 minutes. Moreover, its Nano Blue Coating /Titanium Coating with high hardness and heat resistance enables the tool's cutting edge to retain crucial sharpness and lubricity. This provides longevity and produces cutting results of the highest quality..
  • 2-Flute Spiral Flat Nose & Ball Nose End Mills -- Shank Diameter: 3.175mm, Cutting Diameter: 3.175mm, Cutting Length: 17mm, Overall Length: 38mm..
  • Two End Mill Sets -- Shank Diameter: 3.175mm, Cutting Diameter: 0.8 - 3.0mm (0.8/1.0/1.2/1.4/1.6/1.8/2.0/2.2/2.5/3.0mm), Cutting Length: 17mm, Overall Length: 38mm, with Nano blue and Titanium coating..
  • Applicable Materials: Widely used in various materials including plastics, aluminum, circuit board, wood, as well as other precision parts processing. To learn more about how to choose the right bits to meet your needs, please find the Comparison Chart (CNC Bits Buying Guide) at the Product Guides and Documents Section below..
  • Wide Compatibility: The MC40A end mills are compatible with most desktop CNC machines, such as the Genmitsu 3018 Series, as well as other industrial CNC machines. Just make sure you select the correct-sized collet for your device..
Check Stock

CNC Router Bits 1/8' Shank Ball Nose Carbide End Mill Two Flute CNC Spiral Bits Upcut Cutter 3.175mm Carbide End Mill for Alloy Steels/Hardened Steels 10pcs (3.175x32x55mm)

  • DIMENSIONS: 1/8" (3.175mm). Cutting edge diameter, 1/8" (3.175mm). Cutting edge length/flute length, 1/2"(12mm). Overall length, 1-1/2"(38.5mm)..
  • Range of processing：Ball end mills can mill die steel/cast iron/carbon steel/alloy steel/tool steel/ general iron. Ball nose milling cutters can work normally in high temperature environments..
  • High efficiency：Ball nose carbide end mill is a double-blade with helical design, and the large and uniform pin-out groove is conducive to high-speed machining. The sharp double edge can effectively improve the cutting efficiency of the tool..
  • Perfect cutting：The ball mill design of the double-blade ball end milling cutter effectively reduces the burr and increases the wear resistance of the tool..
  • Ball Nose End Mills are Suitable for Side Milling, End Milling, Finish Machining, etc..
Check Stock

Genmitsu 4pcs 2-Flute Tapered Ball Nose End Mills Tungsten Carbide Cutter with Nano Blue Coat R0.25-1.0 1/8” Shank TB04A

  • ... steel alloy that can keep continuous machining 800 minutes. Moreover, its Nano Blue Coating with high hardness and heat resistance enables the tool's cutting edge to retain crucial sharpness and lubricity. This provides longevity and produces cutting results of the highest quality..
  • Cost-Effective: Coming with 4x 2-Flute tapered ball nose end mills, Shank Diameter: 3.175mm, Radius: 0.25, 0.5, 0.75, 1.0mm, Cutting Length: 15mm, Overall Length: 40mm..
  • Versatile: Perfect for 3D machining jobs like molds, rapid prototyping, models and other other precision parts processing, these Tapered ball nose bits can do the best..
  • Applicable Materials: These nano blue coating bits have an HRC rating of 65 and are optimal for milling a wide range of materials, including plastics, aluminum, circuit board, wood, etc. To learn more about how to choose the right bits to meet your needs, please find the Comparison Chart (CNC Bits Buying Guide) at the Product Guides and Documents Section below..
  • Wide Compatibility: Genmitsu TB04A tapered ball nose end mills are compatible with most desktop CNC machines, such as the Genmitsu 3018 Series, as well as other industrial CNC machines. Just make sure you select the correct-sized collet for your device..
Check Stock

YG1 E5G97911 | 1/4x1/4x5/8x2-1/2 AluPwr 3FL HP Carbide Corner Radius End Mill

  • Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life.
  • Four flutes produce a better finish than fewer flutes.
  • Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds.
  • Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Check Stock

Niagara Cutter - SP205-0.500-D2-S.3-Z2 17011645 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, Uncoated (Bright) Finish, Finishing Cut, 35 Degree Helix, 2 Flutes, 3' Overall Length, 0.500' Cutting Diameter, 0.500' Shank Diameter

  • 2 Flute design makes these ideal for plunge cutting when chip removal is not a problem.
  • General purpose end mill for working on all types of materials.
  • Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.
  • Uncoated end mills feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
  • Center Cutting End Mills are designed with "End Teeth" making these ideal for applications such as profiling, pocket and slotting.
Check Stock

Niagara Cutter 17005489 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 4' Overall Length, 0.375' Cutting Diameter, 0.375' Shank Diameter

  • 4 flute design for creating finer finishes and a higher metal removal rate.
  • General purpose end mill for working on all types of materials.
  • Made of extra-fine grade carbide for ultra high transverse rupture strength.
  • Uncoated end mills feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
  • Center Cutting End Mills are designed with "End Teeth" making these ideal for Slotting and Cavity applications.
Check Stock

Niagara Cutter 17011737 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, Uncoated (Bright) Finish, Finishing Cut, 30 Degree Helix, 6 Flutes, 3.25' Overall Length, 0.500' Cutting Diameter, 0.500' Shank Diameter

  • fewer flutes have more chip-carrying capacity and more flutes produce a finer finish.
  • Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel.
  • Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials.
  • Square nose end mills (also called square end) create sharp, unrounded cuts.
  • Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Check Stock

RIP Cutting Tools 6-PC 4-Flute SE AlTiN HP Carbide End Mill Set, Sizes 1/8-1/2

  • Included Sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 1/2.
Check Stock

YG-1 E5021 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 2.5\ Overall Length, 0.25\ Cutting Diameter, 0.25\ Shank Diameter

  • Suitable for general-purpose machining on steel, chromium-nickel steel, and cast iron.
  • Four flutes produce a better finish than fewer flutes.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than uncoated finish, TiN coating, and TiCN coating.
  • Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
  • Square nose end mills (also called square end) create sharp, unrounded cuts.
Check Stock

MNKNENG 8 Set 1/4 inch End Mill Bits 4 Flute Straight Milling Cutter HSS-AL CNC Square Nose End Mill Bits Straight Shank Drill Bits for Wood, Steel, Titanium(6.35mm,4T) 1

  • Dimensions ---- Shank diameter: 1/4inch / 6.35mm.
  • Strong and Durable ---- Milling cutter is made of HHS-AL material, it is high-wearable and has a long life.
  • Smooth cutting and fast chip-removal, gives outstanding cutting performance and wear resistance..
  • Sharp Edge ---- The design of 4 flutes, sharp edge, and superior wear resistance at high cutting speeds.
  • Durable, high precision and not easy to break.
  • easy installation and improved work efficiency..
  • Application ---- 1/4 inch end mill bits are suitable for side milling, end milling, finish machining, etc. For carving, cutting, engraving, milling in materials like die steel, carbon steel, alloy steel, cast iron, tool steel, titanium, aluminum, rosewood, density board, wood, acrylic, PVC, MDF etc..
  • Package Contents ---- 8pcs 1/4” end mills, each is individually packed in a plastic storage box..
Check Stock