Top 20db Gain - BuyWiseBest.com

MUSYSIC MU-D16K Professional 2-Channel 2x8000 Watts D-Class 1.5U Power Amplifier

...y(8Ω) 1V / input lmpedance 20 k Ω baiance / 10 k Ω unbalanced unbalance balancing 20 k / 20 k /.
Three cooling fans / Connectors Input: XLR input, 1/4" input: Speakon connector Output: Speakon, locking type socket, Power Requirements: 90v-250v 50Hz.
Controls Panel: the power switch, channel 1 and channel 2 channel gain control.
After the board: working mode, pressure limit./ lndicators Panel: the power switch, channel 1 and channel 2 channel gain control.
After the board: working mode, pressure limit./ Amplifier Protection With short circuit, overload, overheat, cut peak pressure limit, dc, soft start, relay zero current switch, super audio and radio frequency protection device..

...) 1V / input lmpedance 20 k Ω baiance / 10 k Ω unbalanced unbalance balancing 20 k / 20 k /.
Three cooling fans / Connectors Input: XLR input, 1/4" input: Speakon connector Output: Speakon, locking type socket, Power Requirements: 115v-230v 50/60 hz.
Controls Panel: the power switch, channel 1 and channel 2 channel gain control.
After the board: working mode, pressure limit./ lndicators Panel: the power switch, channel 1 and channel 2 channel gain control.
After the board: working mode, pressure limit./ Amplifier Protection With short circuit, overload, overheat, cut peak pressure limit, dc, soft start, relay zero current switch, super audio and radio frequency protection device..

A full-fledged studio-grade preamplifier, EQ, and distortion generator with multi-instrument and microphone compatibility.
The Gain section controls the overall volume of the unit, the amount of gain between the two internal gain stages, and the gain of each preamp stage in five stages.
Using the new Hi/Lo switch, get ultra clean sounds without breakup when distortion is not needed or achieve a broad spectrum of overdrive, distortion, and fuzz sounds.
A -20dB pad switch on the right side of the unit tame the volume for high output microphones when in XLR input mode.
The new Shift knobs in the EQ section adjust the range of frequencies that the Treble, Middle, and Bass knobs control to give you precision control over the EQ.
The Hi-Pass section spans from 60Hz to 800Hz with a 6dB per octave slope.
Offers 100% clean signal even on acoustic guitar, silent switching to eliminate "switch-pop", and passing phantom power to condenser mics.

Featuring: Adjust gain Control / Output level Display/ EQ Slide Control / Subwoofer Xover Points / Subwoofer Switch.
EQ Center Frequencies: 60, 150, 400, 1K, 2. 5K, 6K and 15Khz / Equalization Range: +/- 12dB.
Input Impedance: 100 Ohm / Input Sensitivity: 4 Volts for 500mV out.
Frequency Response: 20hz to 20kHz +/- dB / Crossover Rolloff: 12dB/Octave / Power Requirement: 11-16V DC.

Logarithmic Amplifier Module: Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
RSSI Linearity: ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
Apply to: Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
Specific Parameters: 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain. Dynamic Range: 100 dB -78 dBm to +22 dBm (Re 50 O). Total Gain: 100 dB. Bandwidth: 500 MHz. Sleep Current: 003c1mA..
Founction: AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation. Input and Output Interface: SMA Female..

Sound sensor module have small volume and low output noise, the fixed gain is 20dB, support 3.3v and 5v.
Low power consumption of sensor is easy to control, more stable and more efficient.
The sound sensor is suitable for assembly, and installed on various small equipment like microphone and robot.
Microphone sound sensor module possess small size, more stable performance and simpler installation.
This module uses professional microphone amplifier IC, which possess high sensitivity.

Featuring: Adjust gain Control / Output level Display/ EQ Slide Control / Subwoofer Xover Points / Subwoofer Switch.
EQ Center Frequencies: 60, 150, 400, 1K, 2. 5K, 6K and 15Khz / Equalization Range: +/- 12dB.
Input Impedance: 100 Ohm / Input Sensitivity: 4 Volts for 500mV out.
Frequency Response: 20hz to 20kHz +/- dB / Crossover Rolloff: 12dB/Octave / Power Requirement: 11-16V DC.

Includes Installation Kit: 20FT RG6 Cable - Wall Mounting Screws.
Super High Quality Outdoor Antenna for OTA TV Signals (Can also be used indoors).
Built-in High Gain Powered Booster - VHF 20-25dB & UHG 25-30dB.
Easy to Install - Built-In Low Noise Circuit: Less than 3dB.

Voltage Range: The analog gain control voltage range is 50mV ~950mV, and the control sensitivity is 20mV/dB.
Two Modes: Positive gain mode, MODE terminal connected to high level, and negative gain mode, MODE terminal connected to low level.
Shielding Shell: The module has a shielding shell and anti reverse connection protection diode.
Squaring Law Detector: Integrated squaring law detector, can also work in automatic gain control mode.

Adjustable EQ Band Frequencies: 40 Hz, 150 Hz, 1 kHz, 20 kHz.
Variable Subwoofer Filter 30 Hz – 250 Hz, Frequency Response 20 Hz – 20 kHz.
Inputs: Front. Outputs: Front, Rear & Sub. Fader Control.
Gain + / - 18 dB, Maximum Input Voltage 16 Volts, Maximum Output Voltage 7 Volts.
Signal to Noise Ratio > 105 dB, Channel Separation 60 dB, Total Harmonic Distortion 0.050.
Dimensions: Depth 7” x Width 4.5” x Height 1.3”.

Dual inputs for two turntables (1 MM & 1 MC), Front panel mono/stereo mode switch.
Balanced and unbalanced outputs, Variable MC impedance adjustment of 50-1050 ohms.
MM Gain options of 40 dB or 50 dB unbalanced (46 dB/56 dB balanced).
MC Gain options of 50 dB or 60 dB unbalanced (56 dB/66 dB balanced).