Top 3 Oil Hose

uxcell 2pcs Lubricating Oil Hose 3mm(1/8-inch) ID x 5mm(3/16-inch) OD 3.3ft Water Tube Black Rubber Tubing

  • 【APPLICATION】- Lubricating Line Hose mainly used to transport lubricating oil.
  • 【Advantage】- Lubricating Hose has Oil resistant, wear-resistant, aging resistant, soft, lightweight, good bending performance, smooth appearance.
  • 【FEATURE】- Lubricating Tube Measures 0.12-inches inside diameter by 0.2-inches outside diameter by 3.28-feet total length. 0.04" thin tube wall providing higher flow rates and working pressure.
  • 【Rubber material】- Lubricating Pipe made in Rubber, which has the characteristics of high-temperature resistance, oil resistance..
  • 【Please Note】- The hose can not transport fuel oil on equipment.
Check Stock

Crankcase Ventilation Valve Oil Separator Hose Compatible with BMW E46 E60 E39 X3 X5 320i, 323i, 325, 325i 328i, 330i, 525i, 528i CCV PCV Valve Ventilation Separator 5 Piece Value Kit 11611432559

  • 【PCV CCV Exhaust Hose For BMW Replacement】Since the whole point of positive crankcase ventilation is to keep these gases out of the crankcase, the PCV valve is designed to close off when this happens and block the back flow of gases. If the PCV valve hose is broken, the gas will not be transferred back into the engine, which will reduce your engine efficiency, increase harmful gas emissions and the probability of engine failure..
  • 【Fit The Following Vehicles】This E46 PCV Valve hose kit is a direct replacement for the original vent hoses and PCV valves on a variety of vehicles. This includes most 3 series and 5 series models from 1997-2005. SEE THE FULL LIST ON THE PRODUCT DESCRIPTION PAGE BELOW..
  • 【Replace Part Numbers】This X3 X5 CCV hose kit can replace 11617504536 / 11617501566 / 11611432559 / 11157532649 which are commonly found on popular BMW model including BMW E46 3 series E39 E60 X3 X5..
  • 【OEM Quality & Direct Fit】Manufactured with high temperature plastic materials & advanced technology, meets OEM standard. Even though this is not a genuine BMW PCV crankcase ventilation oil separator hose, but it works even better and lasts longer. Save your time and fund by replacing the PCV crankcase ventilation oil separator hose yourself..
Check Stock

YaeTek Oil Change Pump Extractor, 12v 60w Marine Oil Change Pump Electric Oil Pump, Diesel/Engine Oil Scavenge Pump for Oil Changes in Car, Boat, Truck, Motorcycle

  • ...nner surface of rotor and stator. The working volume of pump is first to absorb oil from small to large, and then to discharge oil from large to small after absorbing oil. Within one rotation of blade, oil absorption and discharge are completed twice. This cycle continues..
  • 【Package Include】The pump has 1 outlet hose, 1 inlet hose, 2 hose locks and 2 battery clips. Please pay attention to the direction of import and export, positive and negative poles and lock hose lock before use. The suction power of the micro suction pump is limited. Please do not connect other extension tubes..
  • 【Do not pump】Except for engine oil and diesel,do not pump hot oil or when the car engine is running.Car engine must cool complately.Do not pump gas,paraffim,petrol or other inflammable liquids.Do not pump water and it is not suitable for storage or transportation of fuel or other liquids.Do not pump different oils into the same tank. Only pump warm motor-oil(40℃-50℃) do not pump off motor-oil, as long as the motor is running..
Check Stock

EVIL ENERGY 6AN 90 Degree Swivel Hose End Fitting for Braided Fuel Line Aluminum Black

  • ...rong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed..
  • 6AN 90 degree swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line ,clutch hose,turbo line etc. Our swivel fitting is work with nylon braided fuel hose . They are not compatible with PTFE hose, E85, rubber hose ..
  • These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place..
  • Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling..
  • EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service..
Check Stock

EVIL ENERGY 6AN Straight Swivel Hose End Fitting for Braided Fuel Line Aluminum Black 2PCS

  • The female AN6 swivel fittings are made of lightweight aluminum alloy 6061-T6 material for strong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed. Package: 2 PCS..
  • 6AN swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line, clutch hose, turbo line etc. Our swivel fitting is work with nylon braided fuel hose. They are not compatible with PTFE hose, E85, rubber hose..
  • These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place..
  • Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling..
  • EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service..
Check Stock

VEVOR Hydraulic Hose 3/8 inch x 100 ft, Coiled Hydraulic Hose 4800 PSI, Rubber Hydraulic Hose with 2 High-Tensile Steel Wire Braid, Bulk Hydraulic Hose -20°C to 140°C, Hydraulic Oil Flexible Hose

  • 【DURABLE MATERIAL】- The innermost tube and the outer protective cover are constructed of synthetic rubber. The outermost is cover by fabric. The inner material is two high-tensile steel wire braid reinforcement layers..
  • 【100 FT HYDRAULIC HOSE】- The coiled hydraulic hose is 100 ft long in total, the inner diameter is 3/8 inch, and the outer diameter 3/4 inch. With a 4800 PSI working pressure, the hydraulic line is explosion-proof..
  • 【HIGH STRENGTH】- The bulk hydraulic oil hose is constructed of synthetic rubber to resist oil and chemicals, while the outer cover also protects the hose from weather, ozone, abrasion, and corrosion..
  • 【INCREDIBLE FLEXIBILITY】- Wire hose layers provide flexibility and versatility to allow you to install your rubber hose and hydraulic fittings in tight quarters for less vulnerability. It can work between -40 °C and 121 °C..
  • 【VARIOUS USES】- The hose is suitable to carry petroleum, mineral oils, emulsion, hydrocarbons, and water-based hydraulic fluids. It is ideal for construction, agriculture, and other machinery that uses a hydraulic system..
Check Stock

JIFETOR Oil Pressure Tester Kit, Professional Engine Diagnostic Test, 100PSI Pressure Gauge Tool with Hose Adapter for Truck Car ATV

  • ...pressure test tool includes 3 sizes (1/8" NPT, 1/4" NPT, 3/8" NPT) selectable brass adapters, can be connected to the corresponding sizes oil pressure test service port, on most gasoline or small diesel engine, includes car, motorcycle, ATV, truck and so on, which oil pressure not exceeds 100psi..
  • PRESSURE GAUGE AND HOSE: Pressure gauge adopts rubber cover protected 3" large dial. 0-100psi and 0-7bar small scale range with big dial, very easy to read. No pressure holding function, return to zero automatically. The 30" long rubber nylon resin hose, is equipped with a 1/8" NPT brass adapter, can be connected to 1/4" NPT and 3/8" NPT adapters directly. Max working pressure: 300psi.
  • EASY TO OPERATE: When you want to test the oil pressure by this engine oil pressure diagnostic gauge, disassemble the oil pressure sensor first, then screw on the oil pressure gauge, start the vehicle to operate it at a specified speed, the reading in the pressure gauge is the oil pressure of lubrication system. Please refer to equipment manufacturer's operation instruction and compare to the manufacturer's recommended readings.
  • SATISFACTORY CUSTOMER SERVICE: 30 days full refund with returned undamaged JIFETOR engine oil pressure test gauge. Any quality related problem in 1 year....
Check Stock

Upgrade 80W 12V Oil Change Pump Extractor, Changing Diesel Fluid Scavenge Suction Oil Transfer Pump Kit for Car, Jet Ski, Truck, RV, Camper, ATV, Boat, Motorbike, Riding Mowe

  • [Upgrade] The maximum power is upgraded from the previous 60W to 80W, and the overload protection is upgraded to increase safety protection for your operation.In addition, you will get 1 additional outlet hose, 1 inlet hose, 4 hoses in total, but our price remains the same..
  • [Measured extraction speed]Under the premise of engine oil heating, the speed can reach 0.3gal/min, while the diesel extraction speed is 0.6-1gal/min, Voltage: 12V, maximum current: 7A, maximum power: 80W. According to the arrow Install the hose, Inlet Hose is thin, Outlet Hose is thick.
  • [Safe Operation]: To pump oil properly, before use, please heat the car engine to 104°F-140 °F (40℃-60℃) for about 15 minutes to prevent the oil from solidifying and blocking. Tips: it is NOT suitable for gasoline. Do not use this fluid oil change pump to extract water, gearbox oil, or easily flammable liquids (fuel, petrol, etc)..
  • [Application] This oil transfer pump can change engine oil and diesel for cars, boats, motorbikes, trucks, RV and ATV, and other 12V vehicles..
  • [What you get]: Package included: 1 x Pump.
  • 2 x Battery Clamps. Service warranty: 12month warranty and friendly customer service. Please contact us via email if has any questi....
Check Stock

YuanTenhwy 3 PCS 3/8 10mm Brass Hose Barb Tee Fittings With 9 PCS Stainless Steel Clamps For Air/Water Hose Splicer 3-Way-T…

  • 【Size】: The outer diameter of Hose barb fitting is 3/8 inch (10mm).
  • 【Packing list】: 3 PCS of 3-way(Type T) Hose barbs fitting with 9 PCS of stainless steel hose clamp.
  • 【Material】: The hose barbs fitting is made of brass, and the hose clamp is made of stainless steel.
  • 【Features】: corrosion resistance, dimensions in line with standards, and overall smooth without burrs.
  • The solid barb and hose clamp ensure that the hose and the Hose barb fittings are well sealed during connection, and are not easy to leak.
  • 【Application Scenarios】：It is applicable to pipeline installation and maintenance, and is often used to assist in the transportation of gas, water or oil. However, federal laws do not allow the installation of these fittings for drinking water in the United States and its territories..
Check Stock

ABN Engine Cleaning Gun with 4ft Siphon Hose, Siphon Spray Gun Cleaning Kit – Car Engine Cleaner Degreaser Tool

  • DURABLE ENGINE CLEANING GUN: The ABN Engine Degreaser Sprayer High Pressure Cleaning Gun with 4-foot Air Siphon Hose is a high-speed 2-way action syphon spray gun that blasts dirt, grease, and oil quickly from engines and machinery.
  • The compressed air sprayer hose gun features a pressure trigger for maximum efficiency and a long reach nozzle to reach those tight awkward spaces in your engine bay, deck, and wheels.
  • 4-FOOT SIPHON HOSE: Included in this kit is a durable 4-foot tube with a 1/4 inch (6.4 mm) inner diameter that is incredibly easy to attach and maneuver.
  • Simply attach the 4-foot oil siphon hose to your solvent sprayer and dip the other end of the hose into the oils, solvents, cleaners, or insecticides you plan to use.
  • The powerful syphon spray gun operates with a 1-HP or larger air compressor to deliver 3.0 CFM at 90 PSI giving you a great control rate of flow for your project.
  • SPECIFICATIONS: Includes an aluminum air pressure gun, a long reach cleaning nozzle, and 4 feet of siphon tubing with a built-in solution strainer.
  • Attached to the handle is a pressure trigger, a 1/4-inch (6.4 mm) air inlet that attaches to the supplied siphon hose, and a 1/2-inch (12.7 mm) inlet to attach an air compressor.
  • The oil spray gun operates with 1-HP or lar....
Check Stock

Dialed: The secret math of a perfect mountain bike setup

  • [Great Valve Package] In this package, you will get 4pcs brake lever covers and 4pcs compression nuts, 6pcs protective sleeves, 4pcs oliver and 4pcs inserts, 1 roll 2500mm bicycle hydraulic disc brake hose, 1pc bicycle hydraulic hose fitting insert tool and 1pc hydraulic hose cutter, total 25pcs. Complete kit can fully meet your needs, which is ideal for Shimano BH59 System, you don’t need to find and buy other accessories, saving your time and money..
  • [Reliable Material] Brake hose is made of high-quality material and nylon coating, which is durable and stable. 2500mm length pipes can be cut according to your needs. Precision made with fine workmanship, high temperature and low temperature resistance, high blasting coefficient and enough safe. Needle driver insertion tool is made of aluminum alloy CNC process, it feels good and durable..
  • [Hose Fitting Insert Tool] It is easy to use, super utility needle driver insertion tool. Attached hydraulic hose cutter, sharp and achieve precise and smooth cutting, clean and no burrs. Quick change adapter design, it can match with all needle driver olive and barb on the market, making maintenance easier..
  • [How to Use] You can install hose fitting cleanly and gently. First, put the olive into the oil pipe, seco....
Check Stock

Lotyes Quick Oil Change Pump, DC 12V 60W Oil Diesel Fluid Pump Extractor Transfer Pump & Tubes Kit for Car, Boat, Motorbike, Truck, RV, ATV and Other Vehicles

  • ...wise, the oil change pump may have low suction or jammed. Lotyes oil change pump replaces manual operation and works by connecting the clamps to the vehicles 12V battery. It's high efficiency, rapid and saving effort..
  • Clean and Tidy: An ideal equipment for quick and clean oil changes. No more mess tools needed, the hoses and hose clamps in the package can prevent leakage during the extraction process..
  • Easy installation: Install the oil extractor inlet and outlet hose, tighten the hose clamps, connect the power clamps to the vehicles battery and switch the button on..
  • Versatility: This oil transfer pump can change engine oil and diesel for cars, boat, motorbike, truck, RV and ATV and Other Vehicles. WARNING: THIS PRODUCT CAN NOT USE TO EXTRACT WATER, GEARBOX OIL OR FLAMMABLE LIQUIDS(SUCH AS FUEL,PETROL,GASOLINE,ETC)..
  • What You Get: Lotyes oil extractor pump, outlet hose, inlet hose, hose clamps, battery clamps, user guide. We are certain that you will love the design and high quality of the product. Because you are our number 1 priority, we are offering premium customer support and money-back service for a risk-free purchase..
Check Stock