Top Adaptor Fittings

Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP

  • 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Check Stock

Class A Customs | 30 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-3000-BPK-PUMP

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - BPA FREE - NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Gray Water Storage ||WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” (rotate tank to change height or width) Average thickness 7/32” +/- (+/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Balloon Style Threaded Female NPT Standard - fitting will be closed, to use remove inner membrane with razor knife (TWO) .5" Threaded Female NPT Standard - open fitting, unsealed.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT hook garden hose directly to tank doing so will cause tank to explode resulting in damage..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

RV Winterize Blowout Adapter, Blowout Adapter for Winterizing with 1/4 Inch Quick Connecting Plug and 3/4 Inch Garden Water Hose Threading, RV Winterizing Kit with Ball Valve for RV Boat Camper

  • 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check Stock

Quickun 1\ ABS Bulkhead Water Tank Connector Adapter Fitting with Plugs Thru-Bulk Pipe Fitting (Set of 2)

  • 【Size Information】: The double threaded bulkhead fittings are 1 inch G male and 1 inch G female thread(Bulkhead OD: 44.6mm)..
  • 【Included】2Pcs bulkhead adapter and 2Pcs plugs..
  • 【Durable】:Material:ABS.This bulkhead fittings will not fade, crack, or peel..
  • 【Easy to Use】:Drill a 44.6mm hole for installation, then assemble the ABS bulkhead and hose adaptor together.
  • 【Function】:Can be mounted in walls, tanks, or panels. Bulkhead design to make the fitting easy through holes..
Check Stock

Cen-Tec Systems 92014 Universal Extension Vacuum Hose, 20 feet

  • The 92014 is designed to add 20 feet of highly flexible hose length to the hose on your canister or upright.
  • The hose has a 1 ¼” inner diameter and is 20 feet long. The hose will transfer the power of your vacuum without losing power due to its smooth inner diameter..
  • The 92014 is equipped with a unique compression adaptor that will grab on to the curved end on your can¬ister or upright vacuum hose and add the necessary hose length to clean a complete flight of stairs with the vacuum resting safely on the ground. If you own a Hoover vacuum with the unique pin system simply take the compression fitting off and thread on the Hoover adaptor..
  • The 92014 hose comes with two different hose ends to match with your accessories. Typically North Ameri¬can brands used 1.25” accessories while many European brands were designed for use with 1.375” accesso¬ries. The 92014 comes with alternative swivel wand fittings that allow you to match to either or both size of accessories..
  • The flexibility to adaptor to your vacuum by simply adjusting the ends allows the extension hose to work with most popular brands of canisters and upright vacuums including Hoover, Eureka, Bissell, Miele, Royal, Oreck, Sharp, Riccar, Simplicity, Kirby, and Kenmore.
Check Stock

8AN to 6AN 6 AN Male Y Block Fuel Pump Fitting Adapter Aluminum 8 AN to 2 x 6AN 9/16-18 Male Flare Thread Y Tube Connector Black

  • JIC -8 AN male to AN6 x 6AN 9/16"-18 thread flare Y block adaptor reducing fittings, black anodized finish.
  • One-piece design is compact and lightweight, high flow capacity, Y-Blocks feature A/N Style Male inlets and outlets.
  • Hard anodized coating is compatible with alcohol, exotic fuel-additives, water and oil.
  • This eliminates leaks due to poor solder joints or leaky O-rings due to CNC manufacturing process, 8 AN Male to AN6 *2 Male Coupling Union Adaptor.
  • Made of one-piece lightweight 6061-T6 billet aluminium.
Check Stock

Iococee 5 Feet Low Pressure Propane Regulator and Hose,QCC1 Universal Grill Regulator Replacement Parts with 90 Degree Elbow Adaptor for 17 and 22 Blackstone Tabletop Camper Grill

  • PRODUCT CONTAINS:Low pressure propane regulator with 90 degree solid brass propane elbow adaptor with hose plus 3/8" female flare swivel connect kit....
  • MATERIAL:Made of durable rubber and high quality brass fittings for long-lasting use on blackstone tabletop camper grill has very good weather....
  • APPLICATIONS:You can connect it directly to the blackstone tabletop 17"/22" camper grill ,you can also take off 90 degree propane elbow adaptor on the....
  • EASY TO INSTALL: Provides secure,connect the blackstone tabletop camper grill and storage tank, high-quality air tightness, prevent air leakage,....
  • SERVICE GUARANTEE: Committed to providing consumers with the best cost-effective products, If you have any questions during the use, please contact us....
Check Stock

TBVECHI Adaptor 4500PSI Paintball SCBA Fill Station Charging Adapter with 60cm Microbore Hose Diving Cylinder Inflation Valve (CGA320)

  • Inflation Valve Interface Type:1/2 Quick Insertion.
Check Stock

TFCFL Paintball Fill Station 4500PSI PCP SCBA Fill Station Charging Adaptor with 60cm Microbore Hose Diving Cylinder Inflation Valve

  • SMOOTH DESIGN: This paintball fill station Knob type exhaust valve, the air outlet is very smooth, which is safe to use and premium for long service time..
Check Stock

TOOLGUY REPUBLIC Fluid Transfer Pump - Powered by an Air Ratchet or Cordless Drill

  • Can be powered by an air ratchet or cordless drill. Universal adaptor with rubber mounting strap allows all drill sizes to be quickly mounted to pump.
  • Specifically designed for differential or transmission service. One hand operation leaves free hand to manage suction and discharge hoses.
  • Quickly fill or drain fluids: Brake fluid, Power steering fluid, Transmission fluid, Engine oil, Coolant, Gear/Differential oils.
  • Quick couple fittings allow: Easy hose changes, No drip storage of pump. Positive priming.
Check Stock

Weld on Bung 12AN Hose Barb Aluminum Nipple 3/4 inch Barbed Weldable Pipe Adapter Fittings

  • 3/4" (AN 12) hose barb weld in bung adaptor nipple Barbed Weldable for Oil Cooler / Turbo Charger / Braking.
  • Most commonly used when needing to attach AN lines to areas that don't currently have an AN flare.
  • A few examples would be: Intercooler piping, Intake manifold, or even a custom overflow tank.
  • All of our weld on fittings have minimal anodizing to ensure proper and ease of welding.
Check Stock

How to Succeed in Business Without Really Trying

  • Rating - Max 6200 PSI. Orifice size packs are available ranging from 2.0 up to 4.5..
  • Material Quality - Our spray nozzle tips are made of a professional grade stainless steel and a strong plastic outer design for power and precision over long hours of usage..
  • Quick Connect - These 1/4 inch spray nozzle attachments work with most standard quick connect pressure washer fittings. These sprayer tips are a must have adaptor for any power washer use..
  • 5 Pack Includes - 5 identical spray nozzle accessories with 0 degree angle and 4.0 orifice parts..
  • Satisfaction Guarantee - our products are backed by a 30-Day Money Back Guarantee! Customer service and support are available for all Clean Strike products..
Check Stock