Top Adjustable Roller Assemblies

VeVe Inc. T-908; 8 Ft. Boat Trailer Roller Bunks, 1 Pair

  • 8 Ft. Roller Bunks made from 1" x 2" rectangular Aluminum tube ( AMERICAN MADE )..
  • 36 ea. Duel composition rollers ( hard plastic inner core w/ soft outer rubber surface )..
  • Roller Bunk assemblies ( rollers on tubes ) are 4" wide x 2-1/2" tall..
  • Mount to existing carped bunks or bunk mounting brackets..
Check Stock

KILZ MASTER COLLECTION Professional Mini Paint Roller Assembly with 6-Inch High-Density Foam Paint Roller and 14-Inch Roller Cage

  • KILZ MASTER COLLECTION Rollers are made with the finest materials and designed for professional results..
  • KILZ High-Density Foam Mini Roller Assembly provides the roller cover and 14-inch lightweight roller cage to get you started on your next painting project..
  • High-density foam cover provides a smooth finish without any risk of shedding. Use on doors, cabinets and trim..
  • For best results, be sure to not overload your roller with paint, always maintain a wet edge, and do not overwork the paint with your brush and roller..
  • This 6-inch mini-roller assembly includes a high-density foam roller cover and a light weight roller cage..
  • KILZ MASTER COLLECTION offers a variety of premium paint rollers, mini-rollers and assemblies in a variety of sizes for every project..
  • KILZ has been making premium primers, paints, and accessories for 40 years. KILZ was named Paint Brand of the Year in 2015 in the Harris Poll EquiTrend Rankings..
Check Stock

Slide-Co 16472 Bi-Fold Door Slide Guide (1 Pack), Top Mount, Nylon , White

  • This kit is used for the installation or replacement of medium duty by-passing sliding closet door systems.
  • Track dimensions are 71 in. wide x 1-1/16 in. height x 1-9/16 in. depth. This kit uses 7/8 in. outside diameter wheels.
  • Adjustable roller assemblies are constructed of stamped steel brackets and will fit 3/4 in. to 1-3/8 in. thick doors.
  • Constructed of a galvanized steel rolled form track, plastic wheels and floor guide, steel brackets.
  • Kit includes 3/4 in. brass-plated finger pulls.
Check Stock

Prime-Line D 1797 Sliding Door Roller, 1-1/2 inch Steel Ball Bearing, (2-pack)

  • Used to replace rollers that are 1-1/2 in. diameter.
  • Can be mounted using a rivet, a roll pin, drive pin, binder post and screw or bolt and nut to install the roller in place.
  • Contains 2 steel ball bearing wheels, 2 axle pins, 2 roll pins, 2 carriage bolts with nuts, 2 rivet axels and 2 binder posts with #8-32 x 1/2 in. screws.
  • Easy to install in less than 30 minutes with a few simple tools.
  • Can be used in many different patio door or closet door roller assemblies.
Check Stock

KILZ MASTER COLLECTION Professional 6-Inch High-Density Foam Mini Paint Roller Cover, 2-Pack

  • KILZ MASTER COLLECTION Rollers are made with the finest materials and designed for professional results..
  • High-density foam provides a smooth finish on smooth surfaces including doors, trim and furniture..
  • For best results, be sure to not overload your roller with paint, always maintain a wet edge, and do not overwork the paint with your brush and roller..
  • 2-Pack 6" mini foam roller cover. High-density foam provides a smooth finish. Use on doors, cabinets and trim..
  • KILZ MASTER COLLECTION offers a variety of premium paint rollers, mini-rollers and assemblies in a variety of sizes for every project..
  • KILZ has been making premium primers, paints, and accessories for 40 years. KILZ was named Paint Brand of the Year in 2015 in the Harris Poll EquiTrend Rankings..
  • These premium high-density foam paint roller covers are create an even finish with all paint types, surface coatings, and sheens..
Check Stock

Slide-Co 164553 Pocket Door Kit, Steel Reinforced Wood Framing, For 24 inch to 36 inch x 6 feet-8 inch Doors

  • This kit is used for the installation or replacement of medium duty by-passing sliding closet door systems.
  • Track dimensions are 59 in. wide x 1-1/16 in. height x 1-9/16 in. depth. This kit uses 7/8 in. outside diameter wheels.
  • Adjustable roller assemblies are constructed of stamped steel brackets and will fit 3/4 in. to 1-3/8 in. thick doors.
  • Constructed of a galvanized steel rolled form track, plastic wheels and floor guide, steel brackets.
  • Kit includes 3/4 in. brass-plated finger pulls.
Check Stock

NTN Bearing 30206 Tapered Roller Bearing Cone and Cup Set, Steel, 30 mm Bore, 62 mm OD, 17.25 mm Width

  • 30206 Bearing Size: Out Diameter:62mm/2.44 inch.
  • Ealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use.
  • Complete single tapered roller bearing assemblies are generally mounted in opposing pairs on a shaft to evenly distribute loads..
  • They incorporate logarithmic roller and raceway profiles with a optimized surface finish for ultimate roller to flange contact. These features result in reduced noise and smooth operation..
  • Widely used in transmissions, span styleoil or greased, high radial and axial load, trailer and caravan axles, gearboxes and differentials, span..
Check Stock

Gilson SS-15F Economy Sieve Shaker, 230V, 50 Hz, 11\ Length, 17\ Width, 30\ Height

  • Continuous or timed shaking up to 60 minutes in one-minute increments for ease of operation.
  • Adjustable mixing angle between 0 to 15˚ for precise results.
  • Rotary dial controls and amplitude adjustment arm for accurate mixing.
  • Side-arm assemblies with adjustable finger clamps holds eight 500mL or smaller flasks.
  • The Boekel 401000-2 Flask benchtop analog shaker uses 230V at speeds between 0 to 450 oscillations per minute, and has continuous or timed shaking, an adjustable mixing angle, and side-arm assemblies. This shaker reproduces the back and forth action of the human wrist. The unit has continuous or timed shaking up to 60 minutes in one-minute increments for ease of operation. An adjustable mixing angle between 0 to 15˚ provides precise results from a gentle swirl to vigorous agitation. Rotary dial controls and an amplitude adjustment arm provide accurate mixing. Two side-arm assemblies (included) hold eight 500mL or smaller flasks with adjustable finger clamps that can accommodate 1⁄4 to 2" diameter tubes and vessels. The shaker comes with a power cord, instructions, and two Allen wrenches: one 5/32" wrench for side arm installation and one 3/16" wrench for clamp adjustment. Laboratory shakers are used in many analytic procedures, including drug ....
Check Stock

Timken Tapered Roller Bearing Cup - 59429

  • Single cup (outer ring) for connecting to cones (inner ring assemblies, sold separately) to form a complete single tapered roller bearing.
  • Supports both radial and axial loads between a rotating and non-rotating member.
  • Operating temperatures range from -54 to 120 degrees C (-65 to 250 degrees F).
  • High alloy steel for durability and heat tolerance.
  • Open configuration for lubrication applied in place.
Check Stock

Timken Tapered Roller Bearing Cup - 59425

  • Single cup (outer ring) for connecting to cones (inner ring assemblies, sold separately) to form a complete single tapered roller bearing.
  • Supports both radial and axial loads between a rotating and non-rotating member.
  • Operating temperatures range from -54 to 120 degrees C (-65 to 250 degrees F).
  • High alloy steel for durability and heat tolerance.
  • Open configuration for lubrication applied in place.
Check Stock

Milodon 21523 8.25\ Oil Pump Shaft with Bronze Gear for Big Block Mopar

  • Manufactured from 4130 Chrome-moly shaft.
  • Distributor shaft and bronze gear for 383-440 and Hemi.
  • Bronze gear assemblies are for roller cams.
  • Induction heated-treated ends to reduce wear.
Check Stock

Makita 9032 4.4-Amp 3/8-Inch Variable Speed Belt Sander

  • Compact design for sanding in close quarters.
  • 8.2 feet power cord for increased maneuverability.
  • Variable speed control dial (980-5,600 ft./min.) enables user to match the speed to the application.
  • Adjustable sanding arm pivots 100° for hard-to-reach areas.
  • Easily adjustable belt tracking with a turn of a knob.
  • 3 different size arm assemblies and belts available (1/4″”, 3/8″”, 1/2″”) for increased versatility.
  • Electronic speed control dial (980 – 5,600-Feet/min.).
  • Adjustable sanding arm pivots 100-Degree for hard to reach areas.
  • 3 different size arm assemblies and belts available (1/4-Inch, 3/8-Inch, 1/2-Inch) for increased versatility.
Check Stock