Top Brake Lines

NEW CURRIE 70-87 CHEVY C-10 GMC C-15 C1500 TRUCK 2WD 5-LUG REAR END WITH WILWOOD DISC BRAKES, 11\ DRILLED ROTORS, RED CALIPERS, LINES, PARKING BRAKES, AXLES BEARINGS C10 C15, 1982 1983 1984 1985 1986

  • New Currie Enterprises Rear End with 31 Spline Axles with Wilwood Disc Brake Kit including Drilled Rotors and Red Calipers, Parking Brake Cable Kit, and Brake Line Kit for the applications below (Part # GMC7087X5-K7) 003e Currie Crate Rear Ends are designed to be a bolt-in upgrade.
  • Fits: | Chevrolet Trucks: 003e Will Fit All Late-1970 to 1987 C-10 2wd Trucks with 5-Lug wheels | GMC Trucks: 003e Will Fit All Late-1970 to 1987 C15/C1500 2wd Trucks with 5-Lug wheels.
  • Includes: | Currie 9-Plus Centurian Notch-Back Rear End with 31 Spline Axles (Currie # CE-GMC7087X5) 003e 31 Spline performance axle package 003e Housing includes all 3rd member studs installed 003e GMT7087X5 GMC7072X5 GMC7387X5 003e Built to the stock overall width (63 5/8") and pinion offset specs 003e 63 5/8" is measured outside-of-axle-flange to outside-of-axle-flange, in other words, where the wheel bolts on to where the wheel bolts on.
  • Wilwood 11" Disc Brake Kit with Drilled Rotors and Red Calipers (Wilwood Part # 140-11389-DR): | Brake Kit includes: 003e Drilled/Slotted, .810" Thick x 11.00" O.D. Rotors with Hats 003e Low-Profile 4 Piston Dynapro Calipers - Red 003e Drum Parking Brake Assemblies with Caliper Mounting Brackets 003e Bearing Retainers 003e BP-10 Smart Compound Br....
Check Stock

37 Degree AN Flare Tubing Standard Tube Flaring Tool

  • Makes clean, accurate 37 degree single flares for AN hard lines every time.
  • For soft metal tubing such as aluminum, copper, and mild steel, perfect for brake or fuel lines.
  • Works on 3/16", 1/4", 5/16", 3/8", 1/2", and 5/8" OD tubing.
  • Will NOT make 45° flares for standard brake and fuel lines that are NOT compatible with AN hardware.
  • Not recommended for use on Stainless Steel.
Check Stock

Rough Country Front Stainless Brake Lines (fits) 71-78 Chevy GMC Trucks | Suburban | Blazer | Jimmy | 4-6' Lift | 89340S

  • DOT approved brake line kits offer the necessary extra length to install your application, perfect for anyone who wants to swap out poor performing or decaying factory brake lines..
  • Stainless Steel replacements offer superior protection and a seriously long lifespan..
  • Braided stainless steel exterior keeps your lines free from off-road debris, rocks, and mud that can penetrate factory rubber lines..
  • Durable outer layer prevents expansion of the internal Teflon layer. High Quality hollow fasteners at both ends of each brake line and at both ends provide a leak-free flow path..
  • Backed by Rough Country's Lifetime Replacement.
Check Stock

Vector Tools ISO/Bubble Flaring Tool Kit, 9 Piece | Includes Blow-Molded Case W/Mini Pipe Cutter

  • Make your own brake lines with the bubble Flaring I.S.O tool Kit, designed for metric soft steel brake lines requiring an “ISO” or bubble style flare.
  • Lever-lock flaring bar makes tool kit easy to use for professional and DIY mechanics.
  • Suitable for foreign (European, Japanese) and domestic vehicles (cars, SUVs, light trucks).
  • Yoke assembly, Flaring bar, Gauge/wrench, 10mm tubing, 4 adapters for 4.75mm, 6mm, 8mm, 10mm.
  • ISO/Bubble Flaring Tool Kit designed for metric soft steel brake lines where an “ISO” or bubble style flare is required, set included: Yoke Assembly, Flaring Bar, Gauge/Wrench and 4 adapters for 4.75mm, 6mm, 8mm, and 10mm Tubing.
Check Stock

4LifetimeLines 25' 3/16 True Copper-Nickel Alloy Non-Magnetic Brake Line Replacement Tubing Coil and Fitting Kit, Inverted Flare

  • Nickel-copper alloy is very flexible making for super easy bending & flaring for installation - You can hand bend our brake lines with no bending tools needed.
  • Rust and corrosion proofing technology - Our Copper Nickel Alloy lines are the longest lasting line and are much better than standard steel tubing. Copper Nickel lines are ideal for vehicles experiencing harsh weather and environmental conditions.
  • Meets all SAE and ISO specifications - Our tubing is the best quality tubing on the market.
  • We take pride in producing the best fuel, transmission and brake lines in the industry. Our Limited Lifetime warranty protects all of our products against defects for its entirety as long as it is installed correctly.
  • Complete Brake Line Replacement Tubing Kit Assortment - Includes 16 Fittings: 2 x 3/16” (7/16-24) Inverted Tube Nut, 10 x 3/16” (3/8-24) Inverted Tube Nut, 2 x 3/16” (1/2-20) Inverted Tube Nut, 2 x 3/16” (9/16-18) Inverted Tube Nut.
Check Stock

2" DROP SUSPENSION & WILWOOD 4 PISTON BRAKE SET FOR 55-57 CHEVY, CURRIE REAR END, AXLES, 9" FORD POSI-TRAC 3RD MEMBER, RED CALIPERS, 12" ROTORS SPINDLES MASTER CYLINDER BOOSTER CONTROL ARMS

  • Brand New Suspension & 12" Wilwood Brake Kit For 1955-1957 Chevys with 2" Drop Spindles (Part # GMB5557X-K72). This specific set features 2" drop spindles, Rotors, and Red Dynalite 4 piston front calipers & Red Dynalite 4 piston rear calipers. Fits: 1955-1957 Chevrolet Bel Air, Delray, 150, & 210. Excludes All Station Wagons, Sedan Deliveries, and Nomads due to their Bowtie shaped gas tank that requires a centered housing rear end, as opposed to a centered pinion rear end..
  • Includes: *Currie 9-Plus Notch-Back rear end with 31 spline axles (#CE-GMB5557X): Currie crate rear ends are designed to be a bolt-in upgrade. Built to the stock 60” width & pinion specs. Heavy-duty 2" wide leaf spring pads are installed in the stock location for easy bolt-in installation *Southwest Speed 9" Ford Rear End Third Member With Posi Trac-Loc (#603-2078): This kit comes with a 3.70 ratio gear, which is a good cruising ratio. We have ratios from 3.50 to 5.00 that can be substituted in.
  • *Southwest Speed 2" Drop Spindles (SWS Part # 103-9760): SWS drop spindles provide a full 2" drop, while not changing the vehicle's steering geome....
Check Stock

JMMRRR Automotive Brake Caliper Press Tool with 2 PCS Steel Plates Ratcheting Caliper Piston Tool with 360 Degree Swing Ratchet Blue

  • 【2 Groups Of Push Boards Wider Application】This brake caliper press tool has 2 sets spreading plates, the bigger ones more fit for some sextuplet pistons fixed calipers, smaller ones are suitable for disc brake system with twin and quad pistons fixed calipers, or single and twin pistons floating calipers, is designed to "push" the piston back, cannot twist and compress at the same time..
  • 【360° Ratcheting Design】Adopts 360 degree ratchet design, it is easy to get into place and use from any direction, the ratchet is in the centre of the dual piston brake caliper compressor, both spreading plates need pressure to start the ratchet, to ensure correct alignment to prevent the piston from being misaligned and damaging the brake components..
  • 【Brake Hook & Reversing Switch】Two caliper hooks to protect the brake fluid lines and calipers provides maximum protection for the brake fluid lines and the brake calipers, there is a small positive and negative regulation switch on the ratchet, you can flip it to realize the conversion of expand and retract spreading plates..
  • 【Comfortable And Durable】This brake....
Check Stock

JMMRRR Automotive Brake Caliper Press Tool with 2 PCS Steel Plates Ratcheting Caliper Piston Tool with 360 Degree Swing Ratchet Red

  • 【2 Groups Of Push Boards Wider Application】This brake caliper press tool has 2 sets spreading plates, the bigger ones more fit for some sextuplet pistons fixed calipers, smaller ones are suitable for disc brake system with twin and quad pistons fixed calipers, or single and twin pistons floating calipers, is designed to "push" the piston back, cannot twist and compress at the same time..
  • 【360° Ratcheting Design】Adopts 360 degree ratchet design, it is easy to get into place and use from any direction, the ratchet is in the centre of the dual piston brake caliper compressor, both spreading plates need pressure to start the ratchet, to ensure correct alignment to prevent the piston from being misaligned and damaging the brake components..
  • 【Brake Hook & Reversing Switch】Two caliper hooks to protect the brake fluid lines and calipers provides maximum protection for the brake fluid lines and the brake calipers, there is a small positive and negative regulation switch on the ratchet, you can flip it to realize the conversion of expand and retract spreading plates..
  • 【Comfortable And Durable】This brake....
Check Stock

MuHize Brake Line Fittings - 15 Pieces 3/8 -24 Threads Assortment Brake Fitting for 3/16 Inch Brake Line Tube 5 Unions 10 Nuts

  • PACKAGE INCLUDE - MuHize upgraded Brake Fittings Replacement (Pack of 15): ① 5 x 3/8-24 threads unions.
  • ② 10 x 3/8-24 threads nuts. Note：Both the unions and nuts is 3/8-24 threads (regular 3/16 inch tube fitting size) . Please check before shopping!.
  • INVERTED FLARE UNIOn- Any 2 (3/16 inch) brake lines can be easy to joined with Muhize unions. both the sizes for unions and nuts are both 3/8-24 threads, which is the regular brake fitting size for 3/16 inch tube..
  • HIGHER QUALITY - MuHize brake fittings are made of durable brass with unique rust corrosion proofing technology..
  • WIDELY APPLICATION - MuHize 3/8' - 24 threads fittings commonly fits for regular inverted flare/ double flare sizes for 3/16 inch brake lines tube..
  • PROFESSIONAL - MuHize focus on outstanding features and benefits of braking line. 100% brand new & made from excellent materials, and good contact..
Check Stock

Titan 51535 3/16-Inch Double Flaring Tool

  • Set Contents: (1) 3/16-Inch Double Flaring Tool with Removable Handle, (1) Positioning Bolt, (1) Double Ended OP1/OP2 Punch, (1) Container of Die Lubricant.
  • Creates a perfect inverted 45-Degree SAE double flare with 3/16-inch steel and nickel-copper tubing. Not recommended for use on stainless steel tubing..
  • Can be used on the vehicle! Compact design can be used in tight under-car spaces allowing user to repair brake lines in place on the vehicle..
  • Handle can be removed if you prefer to use in a bench vise..
  • SAE Double Flare is an inverted 45-Degree flare typically used in automotive brake line applications. 3/16-Inch brake lines are on almost all cars and trucks making this flaring tool usable with most vehicles..
Check Stock

Eastwood 3/16 in Handheld Tubing Straighteners Coiled to Straight Tubing Tool for Brake & Fuel Line Tube Flaring

  • Works On Steel, Stainless, Copper, And Aluminum.
  • Great For Brake Lines, Fuel Lines And More.
  • This Handheld Tool Allows You To Straighten Steel, Stainless Steel, Aluminum Or Copper Tubing For Brake Systems, Fuel Systems And More.
  • Much Quicker And Less Expensive Than Bench Mounted Tubing Straighteners And You Get Way Better Results Than Trying To Straighten The Tubing By Hand.
Check Stock

Eastwood 3/8 in Handheld Tubing Straighteners Coiled to Straight Tubing Tool for Brake & Fuel Line Tube Flaring

  • Works On Steel, Stainless, Copper, And Aluminum.
  • Great For Brake Lines, Fuel Lines And More.
  • This Handheld Tool Allows You To Straighten Steel, Stainless Steel, Aluminum Or Copper Tubing For Brake Systems, Fuel Systems And More.
  • Much Quicker And Less Expensive Than Bench Mounted Tubing Straighteners And You Get Way Better Results Than Trying To Straighten The Tubing By Hand.
Check Stock