Top Carbide For Dth Bit

DEWALT DW5205 Percussion Set With Tough Case 5-Pieces, Small

  • ROCK CARBIDE tip maximizes carbide surface contact for longer bit life.
  • Four flute design cleans debris out for fast, efficient drilling.
  • Three flats on shank eliminate bit slipping in chuck..
  • For use with electric or cordless hammerdrills..
  • ROCK CARBIDE tip maximizes carbide surface contact for longer bit life..
  • Four flute design cleans debris out for fast, efficient drilling..
Check Stock

DEWALT DW5242 5/8-Inch by 12-Inch Carbide Hammer Drill Bit , Silver

  • ROCK CARBIDE tip maximizes carbide surface contact for longer bit life.
  • Four flute design cleans debris out for fast, efficient drilling.
  • Three flats on shank eliminate bit slipping in chuck.
  • ROCK CARBIDE tip maximizes carbide surface contact for longer bit life..
  • Three flats on shank eliminate bit slipping in chuck (except DW5232, DW5233, DW5237, DW5238).
Check Stock

4\ Carbide Grit Hole Saw with Arbor & Drill bit for Brick, Stucco

  • This Carbide grit hole saw bit includes 4” 102mm hole saw cutter, 1 of 0.43”(11mm) hex shank mandrel, 1 of 3.5”(89mm) carbide tipped pilot drill bit , Extra 1 of 3m tape measure..
  • This Carbide hole saw bit is your ideal choice for Hardy Plank, Drywall, fiber cement siding , backer board, stucco, Plasterboard.
  • The carbide grit edge hardness overs 80HRC.It is more hard, sharp . It’s a longer life in abrasive material. The Carbide hole saw bit cuts through a wide range of abrasive materials.
  • The specially designing edge cuts more clean ,smooth . It is more fast than tradition hole saw up to 50%..
Check Stock

[2022 Upgraded]Depvko 3Pcs Nail Drill Bits Set, 5 in 1 Drill Bits for Nails 3/32 Inches, Tapered Barrel and Cone Shape Carbide Nail Drill Bits for Acrylic or Gel Remover

  • What You Will Get? 1pc 5 in 1 Purple Nail Bit(Fine) 1Pc Tapered Barrel Carbide Nail Bit(Medium) 1Pc Cone Shape Carbide Nail Bit(Fine)|Shank size: 3/32".
  • Multi-function 5 in 1 Drill Bit: From the upper part of the base of the drill, the roughness changes from fine, to middle, to thick. No need to change another bit for different sizes during the work. Works for both left and right hand with 2 Rotate Direction.
  • Tapered Barrel Carbide Nail Bit: Includes a finer grit at the tip of the bit to avoid any damage to the cuticle and surrounding nail wall and a coarser grit towards the base of the bit..
  • Cone Shape Carbide Bit: Rounded at the top with skinny barrels to help reach the problem areas and to get close to the cuticles and sidewalls..
  • [TUNGSTEN CARBIDE] Made with the hardest material next to diamonds, which will provide durability for long-lasting use without the fear of getting dull, with flute-like cuts for excellent cutting and smoothing performance..
Check Stock

Nail Drill Bit Set Carbide Nail Drill Bits 11PCS Tungsten Ceramic Nail Bits Kit Acrylic Nail Drill Bit Set, Diamond Efile Nail Drill Bits Cuticle Poly Gel Nail Drill Bits, 3/32 Nail Drill Bit Set

  • ❥Professional Nail Drill Bit Set: 11 PCS nail drill bits for drill bits for nails( 8PCS colorful tungsten carbide nail drill bits, 1PCS light pink Ceramic nail drill bit, 1PCS blue silicone nail polish bit, and 1 PCS brush bit. You can finish exquisite acrylic nails faster than doing with nail file buffer sanding block or polishing bar..
  • ❥Multipurpose Combination: Cone drill bits for nails (Coarse grit).
  • Upgraded barrel ball tungsten carbide bit(Middle#1 grit).
  • Upgraded cylinder tungsten carbide bit(Fine grit).
  • Smooth tungsten carbide nail drill cuticle bits(X Fine grit).
  • Brush bit. Great nail file tool set for home salon dip manicure Pedicure..
  • ❥Universal nail drill bits3/32″ Shank: Suitable for most nail drill machines. It is easy to use, just insert or unplug the efile nail drill bits, and select the level on your nail machine.( Note: Please be careful when you use the powerful nail drill bits with sharp grit)..
  • ❥Compact Nail Drill Bit Holder: Come with little cute nail drill bit organizer, easy to store or take along anywhere. The dust proof and transparent nail drill bit case helps you figure out the desired nail drill bits for acrylic nails quickly. Best gift for nail art lovers..
Check Stock

CNC Spoilboard Surfacing Router Bit, 1/2\ Shank 2\ Cutting Diameter, Insert Carbide Slab Flattening Router Bit Planing Bit Wood Planer Bit by BINSTAK

  • 3-WING INSERT CNC ROUTER BIT: Shank: 1/2".
  • Carbide Inserts: 12*12mm. 3-wing design, resulting in a more balanced tool while running..
  • INDUSTRIAL GRADE CNC WOOD ROUTER BIT: Super-strength steel body with anti kickback design, 3 cutting blades..
  • COST-EFFECTIVE INSERT BIT: The surfacing router bit utilizes 4-sided solid carbide inserts. All 4 edges of carbide inserts can be used, use a screwdriver to make other blade edge outside. Replace the carbide inserts when needed, instead of replacing the whole bit. Cost effective solution compared to brazed router bits and solid carbide spiral bits..
  • This planer router bit is perfect for wood slabs flattening, resurface or plane the top surface of the spoilboard. Used on soft and hard woods, particle board, MDF, plywood compact panel, laminate, acrylic and etc..
  • Use on CNC and other automatic routers as well as hand-held and table-mounted portable routers. Such as woodworking engraving machine, trimming machine, etc..
Check Stock

Tungsten Carbide Electric Nail Drill Bits Set for Acrylic Nails 3/32”, Emery Safety Professional Cuticle Diamond Bits for Manicure Efile, 7 Pieces Acrylic Gel Nail Kits Nail Art Salon Tools Home Use

  • [USEFUL] 7 pieces acrylic nail drill bits for professional manicurists and non-professional manicure enthusiasts: 1 x tungsten carbide fine barrel bit, 1 x tungsten carbide medium barrel bit, 1 x tungsten carbide coarse safety barrel bit, 1 x emery cone bit, 1 x emery needle bit, 1 x emery ball bit and 1 x cleaning brush..
  • [MULTI-FUNCTION] AIRSEE nail drill bit set can be used easily and quickly for reshaping, shortening, polishing naturel nails or acrylic nails, for removing cuticles, acrylic nails, nail polish, nail decorations and for cleaning under-nail, etc. A brush is also included to clean up the dust and debris caused by the manicure work..
  • [COMPLETE] Regardless of nail plate, nail edge or nail seam, our drill bit set for nails can easily reach. 3 of different roughness tungsten carbide bits are good at large area work, 3 of emery cuticle drill bits for nails or nail drills are good at safe edge and seam work. At the same time, our nail drill bits for acrylic nails also fully consider the safety and will not harm your skin at all..
  • [PROFESSIONAL] Superior tungsten carbide & emery materials: Tungsten carbide and emery are both corrosion and heat resistant abrasive materials that are almost as tough as diamond so they can provide you with the most....
Check Stock

CNC Spoilboard Surfacing Router Bit, 1/4' Shank 1' Cutting Diameter, Carbide Insert Slab Flattening Router Bits Planing Bit Wood Planer Bit Woodworking Tools by BINSTAK

  • 2-WING INSERT CNC ROUTER BIT: Shank: 1/4″.
  • Carbide Inserts: 12*12mm. 2-wing design, resulting in a more balanced tool while running..
  • INDUSTRIAL GRADE CNC WOOD ROUTER BIT: Super-strength steel body with anti kickback design, 2 cutting blades..
  • COST-EFFECTIVE INSERT BIT: The surfacing router bit utilizes 4-sided solid carbide inserts. All 4 edges of carbide inserts can be used, use a screwdriver to make other blade edge outside. Replace the carbide inserts when needed, instead of replacing the whole bit. Cost effective solution compared to brazed router bits and solid carbide spiral bits..
  • This planer router bit is perfect for wood slabs flattening, resurface or plane the top surface of the spoilboard. Used on soft and hard woods, particle board, MDF, plywood compact panel, laminate, acrylic and etc..
  • Use on CNC and other automatic routers as well as hand-held and table-mounted portable routers. Such as woodworking engraving machine, trimming machine, etc..
Check Stock

CNC Spoilboard Surfacing Router Bit, 1/4\ Shank 1-1/2\ Cutting Diameter, Carbide Insert Slab Flattening Router Bits Planing Bit Wood Planer Bit Woodworking Tools by BINSTAK

  • 2-WING INSERT CNC ROUTER BIT: Shank: 1/4".
  • Carbide Inserts: 12*12mm. 2-wing design, resulting in a more balanced tool while running..
  • INDUSTRIAL GRADE CNC WOOD ROUTER BIT: Super-strength steel body with anti kickback design, 2 cutting blades..
  • COST-EFFECTIVE INSERT BIT: The surfacing router bit utilizes 4-sided solid carbide inserts. All 4 edges of carbide inserts can be used, use a screwdriver to make other blade edge outside. Replace the carbide inserts when needed, instead of replacing the whole bit. Cost effective solution compared to brazed router bits and solid carbide spiral bits..
  • This planer router bit is perfect for wood slabs flattening, resurface or plane the top surface of the spoilboard. Used on soft and hard woods, particle board, MDF, plywood compact panel, laminate, acrylic and etc..
  • Use on CNC and other automatic routers as well as hand-held and table-mounted portable routers. Such as woodworking engraving machine, trimming machine, etc..
Check Stock

BINSTAK CNC Spoilboard Surfacing Router Bit 1/4 Shank Slab Flattening Router Bit with 1-3/8 Cutting Diameter 2+2 Flutes Insert Carbide Wood Planer Router Bits Planing Bit for Woodworking

  • Carbide Inserts: 12*12mm. 2+2 inserts design, resulting in a more balanced tool while running and get a smoother surface. The Router Bit comes with insert blades. For more blades, please purchase the K1222 model. ASIN：B0B1MJ9Z9P.
  • INDUSTRIAL GRADE CNC WOOD ROUTER BIT: Super-strength steel body with anti kickback design, 4 cutting blades..
  • COST-EFFECTIVE INSERT BIT: The surfacing router bit utilizes 4-sided solid carbide inserts. All 4 edges of carbide inserts can be used, use a screwdriver to make other blade edge outside. Replace the carbide inserts when needed, instead of replacing the whole bit. Cost effective solution compared to brazed router bits and solid carbide spiral bits..
  • This planer router bit is perfect for wood slabs flattening, resurface or plane the top surface of the spoilboard. Used on soft and hard woods, particle board, MDF, plywood compact panel, laminate, acrylic and etc..
  • Use on CNC and other automatic routers as well as hand-held and table-mounted portable routers. Such as woodworking engraving machine, trimming machine, etc..
Check Stock

5 PC 3/8'' Indexable Carbide Insert Lathe Turning Tool Bit + 10 Pc Tips COMBO

  • 5 PC 3/8'' indexable carbide insert turning tool bit set + 10 PC carbide tip combo.
  • 5 PC 3/8'' indexable carbide insert turning tool bit set specs:Shank Diameter: 3/8".
  • AL/AR Style 0 degree Lead, BL/BR Style 15 degree Lead, E Style 30 degree Lead.
  • 10 PC 3/8'' Inserts TCMT 2151 specs:Case overall dimension: 1-1/2''L x 3-3/4''W x 1/2''H.
  • Quantity: 1 set (5 pcs 3/8'' indexable carbide turn tool bit set + 10 pc carbide tips).
Check Stock

Wacom Cintiq Adjustable Stand

  • Includes VESA FDMI (mis-d75) for use with a Display arm.
  • Compatible with Wacom Cintiq 16 (DTK1660K0A), not compatible with Wacom Cintiq Pro 13 (DTH1320), Cintiq Pro 16 (DTH1620 / DTH167K0A), Cintiq Pro 24....
Check Stock