Top Chip Type Thermistor

HICTOP 100K ohm NTC 3950 Thermistors/Temp Sensor for Reprap Creality Ender 3 Ender 3 Pro CR-10 10S 3D Printer Pack of 5 1m/39.4inches

  • HICTOP 3d printer thermistor can be used on both of the heated bed and the extruder for 3d printers.
  • The thermisor is compatible with most 3D printers in the market such as ender3, ender3 pro, ender3 V2, CR-10, hictop d3 hero etc.
  • There is a 2 pin female connector on the thermistor for 3D printer.
  • Wire length for the thermistor: 1m/39.4 inches.
  • Recommended parameters for the thermistor: R25℃=100K B25/50=3950K± 1%.
Check Stock

5-PCS Ender 3 Thermistor HT-NTC100K 3D Printer ntc 3950 100K Thermistor Sensor for Creality Ender 3 v2 Thermistor Upgrade Compatible with E3D V6 Volcano PT100 Ender-3-5 Pro CR10 hotend,

  • （Ender 3 Thermistor, Upgrade HT-NTC100K Thermistor (1 meter each)）：Cartridge temperature sensor. Metal head diameter: 3mm, head length: 15mm,cable wire length: 1 meter,connector: XH2.54 2PIN, （Suitable for heating blocks with holes of 3mm*15mm-3mm*20mm）.
  • Compatibility：Product recommended operating temperature -50 °C ~ +280 °C, can replace the cartridge K-type thermocouple temperature sensor. Suitable to print multi kinds of filament.Compatible with the heatblocks with 3mm hole,such as: V6 Volcano PT100 type heated block,CR10 plated copper high temperature heating block,etc.
  • Stability and Accuracy：Encapsulated in copper case,copper material has better thermal conductivity than stainless steel and improves accuracy.Secured with high temperature adhesive,high stability, no falling off.The internal temperature package to ensure the maximum service life with precision temperature measurement..
  • Long Service Life：Compared with other products of the same type that are insulated with ordinary heat shrinkable tubes, this product uses glass fiber with a temperature resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temperature work. Thereby increasing the service life..
Check Stock

8577274 Thermistor for Whirlpool Dryers by PartsBroz - Replaces WP8577274, AP6013514, 3390292, 3406294, 3976615, 772546, ER8577274, PS11746740, WP8577274VP

  • ✅ PART NUMBER 8577274: The thermistor is a high-quality exact replacement for part numbers WP8577274, AP6013514, 8577274, 3390292, 3406294, 3976615, 772546, ER8577274, PS11746740, and WP8577274VP..
  • ✅ FOR WHIRLPOOL DRYERS: Use the part to fix select Whirlpool, KitchenAid, Kenmore/Sears, and Maytag dryers. Check your dryer manual or reach out to us to confirm compatibility with your model..
  • ✅ FIXES COMMON PROBLEMS: Dryer on the fritz? Replacing the thermistor, which regulates temperature in your dryer, can fix dryers that don’t produce enough heat, don’t start, or shut off too soon..
  • ✅ SIMPLE DIY FIX: Remove a faulty thermistor and install this new one in under 20 minutes. Helpful tools include a 1/4-inch nut driver, a small flathead screwdriver, and a 1/4-inch socket and ratchet..
  • ✅ HIGH-QUALITY PART: Designed to last, this thermistor meets or exceeds all original manufacturer specifications for performance and fit..
Check Stock

WINSINN HT-NTC100K Thermistor Sensor Ender 3 v2 Upgrade 3x15 3950 XH2.54 2Pin Compatible with Ender 3 5 Pro CR6 CR10 Series 3D Printer Hotend Pack of 5Pcs

  • ✔️Upgrade HT-NTC100K Thermistor: package temperature measurement. Head diameter: 3mm, Head length: 15mm.
  • ✔️The temperature measurement: -50 °C ~ +350 °C, can replace the original K-type thermocouple temperature. Fit for printing high-temperature....
  • ✔️Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement..
  • ✔️HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line....
  • ✔️Made by WINSINN. Can be used with the New Sensor Heater Block (Temperature measurement can be up to 350 degrees)..
Check Stock

Game Source SDHC Gold Adapter With 32 GB Micro SD With YS Menu With 500 In 1 Will Work On DS DSI DSIXL 2DS 2DSXL 3DS 3DSXL

  • ...rboard, users can enter DFU mode through USB to update the firmware.
  • Superior Security: The EBB series has been optimized in multiple dimensions in terms of security. USB power-on is selected by jumper cap, which effectively isolates the DC-DC and USB 5V of the main board, and increases the protection circuit of the thermistor part to avoid the burning of the main control chip due to the leakage of the heating rod. The USB port adds an ESD protection chip to prevent the main control from being damaged. Electrostatic breakdown of the USB port..
  • Rich Expansion Functions: I2C interface is reserved. This port can also be used for material breakage, material blocking detection, or DIY operations for other functions. The factory is equipped with terminals, female reeds, double-way studs and screws for Meet the DIY needs of customers.
  • Quality Commitment: Q: When updating firmware, it may be a risk that the heater sticks keep heating up A: please pay attention to disconnect the main power VIN of the hotend when using the DFU of Type-C port to update the firmware, or ensure that the firmware update is completed soon and goto the normal working mode. Never keep MCU in DFU mode for a long time when the main power supply and hotend are connected.If you still have a....
Check Stock

BIGTREETECH SKR PICO V1.0 Control Board: Mini Controller Board with TMC2209 UART Stepper Motor and Raspberry Pi Online Printing for Voron V0 V0.1 3D Printer Parts

  • 【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
  • 【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
  • And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V..
  • 【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to realize Klipper Firmware and Raspberry Pi Online Printing..
  • 【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion.
  • at the same time reserved WIFI interface, PT100 thermistor interface (optional, Only reserved interfaces, customers need to purchase chip welding, please pay attention.), dual Z-axis printer..
  • 【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard. Supports “print from SD card” and “print via USB OTG” using the integrated USB-A port..
Check Stock

279973 & 3392519 & 8577274 Dryer Thermal Cut Off Fuse Kit with Thermistor Control and Thermal Fuse Replacement Part fit for Whirlpool & Kenmore Dryers

  • ✅Package Includes: 1 x 279973 Thermal Fuse & Thermostat with Instruction Sheet, 1 x 3392519 Thermal Fuse, 1 x 8577274 Thermistor Control..
  • ✅279973 Thermal Fuse & Thermostat – Dryer high limit thermal fuse and high limit thermostat kit. Includes instructions..
  • ✅3392519 Thermal Fuse – Dryer non resettable thermal fuse, two 3/16″ wire terminals. This fuse is located on the blower housing next to the blower fan. If the dryer overheats, the thermal fuse blows to cut off power to the dryer and/or stop the dryer from running..
  • ✅8577274 Thermistor Control – Dryer thermistor temperature sensor..
  • ✅Replaces Part Number – Thermal Fuse & Thermostat 279973 3391913 3404151 3404152 3977395 8318314 897710 AP3094323 PS334387 EAP334387. Thermal Fuse 3392519 WP3392519 3388651 694511 80005 ET401 G4AP0500 3392519 PS11741460 AP6008325 2986 EAP11741460. Thermistor Control 8577274 WP8577274 3390292 3406294 3976615 772546 8577274 1181075 AP6013514 PS11746740 EAP11746740. the replacement part is a direct replacement for your dryer..
  • ✅Buy with Confidence – Order from KONDUONE, you can return or exchange within 3 months, true worry-free shopping experience. If replacement part ever fails on your Dryer simply con....
Check Stock

LG LW8022IVSM Window Air Conditioner 8000 Cooling BTU, 340 sq. ft. Cooling Area, Works with Google Assistant/Amazon Alexa, Quiet Operation, in White

  • Size: Width 19.57" Height 12.5" Depth 24.5" Volts: 115. Amps: 15. Frequency: 60 Hz..
  • Plug Type: 5-15P. CEER: 15.5. Programmable Timer: Yes. Cooling Area: 340 sq. ft. Maximum Air Flow: 190 CFM. Wi-Fi: Yes. Smart Appliance: Yes.
  • LW8022IVSM 8,000 BTU DUAL Inverter Window Air Conditioner: Cooling: 8,000 BTU, Estimated Cooling Area: 340 sq. ft. LoDecibel Quiet Operation..
  • Other Features: Thermostat Control: Thermistor. Air Deflection: 4-Way. Remote Controller: Yes. Auto Restart: Yes. Energy Saver Function :Yes.
  • Other Features: Timer: 24Hr, On / Off. Filter Alarm Function: Yes. Fan Speed (Cooling): 4. Fan Only: 3. In Door Fan Type: Turbo. Type Air. Discharge: Top Discharge. Outdoor Vent / Exhaust: No. Chassis Type: Top Down.
Check Stock

LG Smart Wifi Enabled Window Air Conditioner with Cooling Speed in White (LW1022IVSM - 10000 BTU)

  • Size: Width 19.57" Height 12.5" Depth 24.5" Volts: 115 Volts, Amps: 15 Amps, Frequency: 60 Hz..
  • Wireless Remote Controller: Included. CEER: 15. Programmable Timer: Yes. Cooling Area: 450 sq. ft. Number of Cooling Speeds: 4. Maximum Air Flow: 215 CFM. Wi-Fi: Yes. Smart Appliance: Yes.
  • 10,000 BTU DUAL Inverter Smart Wi-Fi Enabled Window Air Conditioner: Cooling: 10,000 BTU, Estimated Cooling Area: 450 sq. ft. up to 35% Quiet Operation, LG Technology.
  • Other Features: Wi-Fi Connection: Yes.Thermostat Control: Thermistor. Air Deflection: 4-Way. Remote Controller: Yes. Auto Restart: Yes. Energy Saver Function: Yes.
  • Other Features: Timer: 24Hr, On / Off. Filter Alarm Function: Yes. Fan Speed (Cooling): 4 Fan Only: 3. In Door Fan Type: Turbo. Type Air Discharge: Top Discharge. Outdoor Vent / Exhaust: No. Chassis Type: Top Down.
Check Stock

8577274 Dryer Thermistor compatible with Whirlpool Kenmore Dryer - Replace 3976615 AP3919451 WP8577274 PS993287 by Seentech (1PCS)

  • ✅ MODEL NUMBER: 8577274 Dryer Thermistor.
  • ✅ BRAND NAME COMPATIBILITY: It’s a direct fit for several Whirlpool, Kenmore, KitchenAid: REPLACEMENT PART No: WP8577274, AP6013514, 8577274, 3390292, 3406294, 3976615, 772546, ER8577274, PS11746740, and WP8577274VP..
  • ✅ HIGH QUALITY RELIABLE : The fuse is made of high quality material and tested. Forget the repairman. It only takes 20 to 30 minutes to remove a faulty thermistor and install this new one. Helpful tools include a 1/4-inch nut driver, a small flathead screwdriver, and a 1/4-inch socket and ratchet..
  • ✅ SAVE TIME SAVE MONEY: Inexpensive way to fix or repair a dryer. Replacing the thermistor, which regulates temperature in your dryer, can fix dryers that don’t produce enough heat, don’t start, or shut off too soon..
  • ✅ MONEY-BACK GUARANTEE: For any reason you're not completely satisfied, you can ask for a replacement or full refund, no questions asked..
Check Stock

Edgewater Parts 2188819 AP6006067 PS11739131 Refrigerator Thermistor Compatible with Kenmore KitchenAid Whirlpool and Maytag

  • A thermistor is used to detect the temperature in the air inside of your refrigerator..
  • This product is covered under a 1 Year Warranty.
  • Edgewater Parts 2188819, AP6006067, PS11739131 Refrigerator Thermistor Compatible with Kenmore, KitchenAid, Whirlpool, and Maytag.
Check Stock

Deror Digital Vacuum Gauge,VMV-1 High Precision Digital Vacuum Gauge for Atmospheric Environment 0-50 Degree Celsius

  • Accuracy: ±10% (0 to 100 microns), ±6% (101 to 750 microns)..
  • Resolution: 0 to 20: 0.2 micron, 21 to 200:1 micron, 201–500:5 microns.
  • Auto Shutoff: After 10 min. if vacuum value 003e18000 microns, After 30 min. if vacuum value 003c18000 microns..
  • Operating Temperature: 0°C to 40°C / (+32°F to 104°F).
  • Storage Temperature: -20°C to 60°C / (-4°F to 140°F).
  • Engineering Units: microns, mbar, Pa,Torr, mTorr, psi, inHG.
  • Battery Life: 40 hours | Connector Type: Standard male ¼ inch.
  • Supply Scope: 1 Unit of Refco vacuum Gauge, Hanging Hook, T-Joint, Instruction Manual | Applications: HVAC, Biotech, Food, Freeze Drying, Vacuum Furnaces, Refrigerants, Beverage Industries, Pharmaceutical.
Check Stock