Top Circuit Board Relay
Electronics-Salon 8 Channel DPDT Signal Relay Module Board (Operating Voltage: DC 5V)
- 8 Channel DPDT Signal Relay Module Board, DC 5V Version..
- FR-4 fiber glass PCB, dual copper layers. Dimensions: 72.5mm x 150mm ( L x W )..
- RY5W-K high quality signal relays, LED indicator for each relay channel. Darlington transistors circuit driving relay, improve the reliability of action..
- Pitch 3.81mm / 0.15" screw terminal block, wire range 26-16AWG, strip length 5mm / 0.2", Metric M2 slotted screw..
- Datasheet: https://images-na.ssl-images-amazon.com/images/I/A1vg1+5HA8L.pdf.
Check StockCW QRP Shortwave Radio Kit - CW Transceiver Shortwave Radio Kit
- The patch device of the main control board has been pre welded and connected to the base plate in the form of stamp hole. The single chip microcomputer adopts pic16f1938, builtin PLL local oscillator, supports crystal oscillator calibration setting, and has its own frequency indication circuit (Seven Segment LED nixie tube is used, the display unit is 1kHz, the photo has color difference, and the actual color is red. The working frequency covers 7.000-7.100mhz, 1kHz or 100Hz steps )..
- Ta2003 mixer is used for reception, and crystal filter is used for if. After ta2003 multiplication detection, the sound size is adjusted by digital potentiometer and sent to audio active filter circuit. Finally, LM386 drives speaker, and if frequency supports calibration setting..
- Use 3 bs170 parallel outputs, class E amplification, 12V power supply, output power 5W! Relay switching is used for transceiver, with the function of transmitting delay adjustment to avoid frequent relay switching and improve the isolation of transceiver channel..
- It has the function of automatically sending call signs, which is very convenient to use. The MCU uses the original code of our store, which can adjust the code speed, sidetone frequency and sidetone size. It can input the call sign by ....
Check StockDorhea ESP8266 ESP-12 NodeMcu D1 Module WeMos Lua 4M Bytes WLAN WiFi Internet Development Board + Relay Shield + 2.54mm 40Pin Single Row Male Pin Header - 3Set
- The esp8266 module is 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
- 1 analog input(3.2V max input). Micro USB connection.
- WiFi internet development board 5V 1A switching power supply (switching power supply)onboard..
- 5V relay shield is a digital switch to control much higher voltages and currents than esp8266 mini microcontroller, controlled by the D1 , the relay will switch to allow current to flow or turn off, depending on wiring..
- 40 pin 0.1inch (2.54mm) male pin header connector PCB board pin strip electronic component, they are easy to be cut to any length if needed, you can cut or score with some electronic tool..
- The pin header is an ideal connector for the PCB board and intergrated circuit, used widely in the computer and breadboard, compatible with raspberry pi or other electronic project..
Check Stock5V ESP8266 Dual Channel WiFi Relay Module IOT Smart Home Phone APP Remote Switch with 100M Transmission Distance
- ON-BOARD ESP-01 WIFI MODULE: The relay board is equipped with on-board ESP-01 WiFi module and high performance microprocessor STM8S103..
- UART DEBUG INTERFACE: The relay has reserved UART debug interface and STM8 SWIM program download interface..
- SMART CONFIG TECHNOLOGY: The module uses smart config technology to complete the account and password configuration on the APP ESP-01 WiFi module on the mobile phone, and configure the username and password memory functions..
- ON-BOARD 5V RELAY: This relay module adopts On-board 5V,10A250V AC 10A30V DC relay, which can continuously pull 100,000 times with diode discharge protection and short response time..
- WORKING STATUS INDICATOR: The module has board mode selection and real-time working status indicator..
Check StockLG EBR74164805 Genuine OEM Relay Control Board for LG Range/Stove/Ovens
- This LG Relay Control Board is a genuine OEM (Original Equipment Manufacturer) part manufactured to exact specifications.
- Replacement LG brand Range/Stove/Oven Relay Control Board operates relays to regulate the oven elements.
- LG EBR74164805 Range/Stove/Oven Relay Control Board receives signals from the main oven control board.
- High quality LG OEM EBR74164805 Range/Stove/Oven Relay Control Board is manufactured with premium materials for durability and exact fit, be sure to....
- Life's Good when choosing Genuine LG OEM Factory parts for your LG appliances.
Check Stock[2 Pack] DC 6-30V Timer Relay Programmable Delay Relay Module Cycle Timer with LCD Display / 5V Micro USB, Smart Home Controller
- 【Multifunction Timer Relay】Programmable delay modes to control the relay timings, widely used at smart home, industrial control, automatic irrigation, indoor ventilation, protection equipment etc..
- 【Load Range】Operating voltage: DC 6V - 30V, support micro USB 5V power supply. High level trigger: 3V - 24V. NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Timing range: 0.1s ~ 999mins (continuously adjustable)..
- 【Reverse Protection】Built-in a diode to provide protection against accidental reverse polarity for the circuits..
- 【Sleep Mode】If no operation within 5 minutes, the digital tube of the relay board will turn off automatically. Pressing any button can wake it up..
- 【Parameter Setting】OP(conduction time) / CL(off time) / LOP(circuit times) can be set individually, and the parameters are mutually independent. All parameters are permanently saved once set. The functions and parameters can be reviewed or changed at a later time..
Check StockTYC 610610 Hyundai Santa FE Replacement Condenser Cooling Fan Assembly
- Temperature Electrical Switch — Turns on electric fan at 200 Degrees and shut it off at 180 Degrees.
- Compatible With — 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 Engines.
- Relay Switch Kit — New 180 to 200 Degree electric fan thermostat relay switch kit for your cooling system.
- Specifications — 12V 40 Amp 4 Pin Relay & Pigtail, 30 Amp Circuit Breaker, and 3/8" National Pipe Thread (NPT) Switch.
- Kit Inclusions — Sending Unit, Wires, Relay Switch, Circuit Breaker, Terminals.
Check StockIngcool Compatible with Raspberry Pi Expansion Board Power Relay Module Kits for Raspberry Pi 4B/3B+/3B/2B/ A+/B+ 5A 250V AC/ 5A 30V DV
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards.
- The RPi Relay Board gives your Pi the ability to control high voltage/high current devices, easily makes normal home appliances become intelligent..
- High quality relays, loads up to 5A 250V AC or 5A 30V DC.Photo coupling isolation, prevent interference from high voltage circuit.
- Relay control jumper, allows to control the relays by custom pins other than the default pins.Onboard LEDs for indicating relays status.
- Comes with development resources, including examples in wiringPi, WebioPi, shell, python, and bcm2835.
Check Stock70955
- FEATURES: 12 position terminal block for accessory attachment.
- 6 40-amp cube style relays (plug-in style).
- 6 Diodes to prevent LED “field collapse”.
- Inline 50amp manual resetting circuit breaker.
- 8 gauge power leads with crimped and soldered terminal for connection to the battery.
- Integrated LVCO (Low-Voltage-Cut-Off) circuit.
- Fuse for LVCO which can be removed to bypass the LVCO.
- High-temp, abrasion resistant wiring cables.
- KIT CONTENTS: (1) Switch pod w/ 6 Rocker Switches, (1) Switch pod wiring harness, (2) Switch pod mounting brackets, (1) Relay pod, (1) Relay pod power wire, (1) Relay pod ground wire, Mounting hardware.
Check StockATD Tools 5614 Relay Circuit Tester
- Able to test an entire circuit - from battery to component, including the relay With this item the technician can jump a relay.
- do an AC charge from the relay by activating the compressor.
- do compression testing by activating the starter relay and even check turn signals or lights from the front of the car.
- Allows the technician to diagnose the problem without the use of a multimeter.
- The lighted display shows the technician the problem immediately.
- With this item the technician can jump a relay.
- Includes: (1) Tester, (6) popular Relay Leads, and (1) Universal Relay Lead.
Check StockWiring Harness,Eyourlife LED Light Bar Wiring Harness Kit 180W 12V 40A Fuse Relay On/Off Switch Relay 14AWG 12FT Length Heavy Duty Universal Fitment(2 Lead)
- Eyourlife Switch Relay: Eyourlife IP56 waterproof power relay and blade fuse proctect circuit safety from overcurrent or short-circuit.Regulate the power to be consistent and prevent any surge..
- 2 Available Leads:One wiring harmess with two light output connectors gives you brilliant solution to install dual Led lights..
- Detail:Operating Voltage: 12V,Amp: 40A ,Power Relay Fuse: 40A ,Blade Fuse: ≤180W.
Check StockWeewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board
- Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
- Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
- The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
- Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
- All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
- High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
- Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock