Top Conduit Fitting Locknuts

VANICE Bike Freewheel Removal Repair Lockring Tool, Compatible with Shimano, Sunrace and Other 12 Spline Freewheels

• Good Compatibility - Compatible with Shimano, Sun Race, Saches and other similar 12 spline freewheels. Not compatible with cassette lock rings.
• High Quality - Heat treated alloy tool steel construction for a lifetime of use.
• Easy To Use - Use any ½” drive ratchet or 21mm spanner wrench to rotate the tool (open end wrench, crescent wrench etc).
• VANICE Professional and pratical bike bicycle freewheel remover tool. Thin wall construction allows use without removal of cones and locknuts.
• CASSETTE OR FREEWHEEL? To determine the type of rear sprocket system you have, find the tool fitting on the sprocket set. Spin the sprockets backwards. If the fitting spins with the cogs, it is a cassette system. If the tool fitting does not spin with the cogs, it is a freewheel system.

Westinghouse Lighting 70272 7027200 12" Lamp Pipe Kit, 1 Pack, Yellow

• 12, all thread lamp pipe Kit, zinc plated steel, includes two: 1/8Iron pipe x 12Threaded pipe, two 1/8Iron pipe couplings.
• Contains two each: 1/8-IP x 12″ threaded pipe, 1/8-IP couplings, 1/8-IP locknuts, 1/8-IP knurled locknuts, washers.

Moto Bearings Y3 Skate Tool

Craftsman Set of Two 187292, 192870, 532187292, 532192870 Spindle Assembly with Grease Zerk, Husqvarna Poulan

• Set of two spindle assemblies, includes blade bolts, mounting bolts, pulley locknuts, spacer..
• Mounting holes have been pre-tapped for easier installation..
• 187292 are the spindle assembly's with grease fittings. Replace the non-grease fitting 192870 with these also..
• Spacer must be installed under the pulley..
• Installing with the spacer on top of the pulley (or failing to use spacer) will result in damage to shaft and pulley..

Oatey 30863 Heavy Duty Solvent Cement, 8 Oz, Can, Liquid, Clear

• Heavy duty Clear cement for use on all schedules and classes PVC pipe and fitting up to 12” diameter with interference fit, up to 18” for non-pressure.
• Low-VOC solvent cement meets California South coast air quality management district (SCAQMD) 1168/316a or baaqmd method 40 and various environmental requirements.
• Heavy Duty Clear cement for use on all schedules and classes PVC pipe and fitting up to 12î diameter with interference fit, up to 18î for non-pressure.
• Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD).
• Thick formula fills gaps in large diameter pipe and loose fitting joints.
• Recommended for potable water, pressure pipe, conduit and DWV.
• Recommended application temperature 40°F to 110°F / 4°C to 43°C.

Grinder Wrench Adjustable Pin Spanner Wrench Angle Grinder Lock-Nut Wrench For Grinders

• ★Pin Spanner Wrench Main Using:The adjustable pin wrench is for use with locknuts on angle grinders when fitting or removing abrasive discs.
• ★Pin Wrench Fit Modle:Suits most grinders and Lock nuts. Ideal Replacement Pin Wrench For All Angle Grinders, Bench Grinders, Circular Saws, and Mitre Saws etc.
• ★Pin Spanner Wrench Design: Pin Wrench Easy twist knob adjustment,Adjustable Extent:10-30mm.Heat treated pins for long lasting and strong grip and rubber dipped handle grip for comfort.
• ★Note:Please allow 1-3 cm difference due to manual measurement.

Banjo TF200SS Stainless Steel 316 Bulkhead Tank Fitting, 2\ NPT Female

TEMCo THA003 2-1/2\ Conduit Punch and Die For Hydraulic Knock Out Driver 3/4\-16 Thread

Little Giant PE-2YSA 518550 Submersible Parts Washer Pump, Black

• 1/4-Inch MNPT discharge and 1/2-Inch MNPT Master Builders conduit fitting.

Lamson E986J-CAR Carlon Access Fitting Type LB

• The product is manufactured in United states.

Wiremold Power Strips Plugmold End Feed Fitting V2010A2

• For connecting 2000 with 1/2" conduit and armored cable connectors.
• 1/2" trade size KO's on end each side and bottom.

Glvaner (10 Sets) M10-1.5 x 25mm Thread Length Flat Round Head Socket Head Cap Screws with Hex Locknuts 304 Stainless Steel Furniture Screws Projects

• Package Includes: 10 Pcs M10 Screws and 10 Pcs M10 Hex Locknuts.
• Material: 304 stainless steel (A2) and no exterior finish, greater strength and corrision resistance performance than regular stianless steel or zinc plated fasteners..
• Included 10 pcs free same size M10 Hex Locknuts to help save your time and money to find nuts.The locknuts are also made of 304 stainless steel and could be found seperately in our shop for your needs..