Top Current Isolation

AC Current Transducer Transmitter Transformer Sensor AC Current Converter AC 0-50A to DC 0-5V SZT15-CH-5V

  • Safe Security: Mutual inductance current monitoring has high current detection accuracy and safe isolation of input and output..
  • Easy To Use: Easy to install and use, no need to connect DC into the circuit when measuring..
  • Product Specification: Self-powered, no external power supply required. Measured current AC 0-10/20/50A, output signal DC 0-5V. Straight-through structure design, isolation withstand voltage up to 2000V..
  • High Quality：The outer casing is made of self-extinguishing material ABS..
  • Widely Application: Hysteresis is less than 1% and can be used under strong magnetic conditions. Suitable for AC current measurement and monitoring, AC motor overload protection, electronic switch of automatic control system and so on..
Check Stock

Intona 7055-C USB 3.0 SuperSpeed Isolator 1kVrms 20kV ESD Protection Supports Full Speed 12Mbps,High Speed hi-Speed 480Mbps and SuperSpeed 5Gbps

  • No external power supply required, up to 500mA current on isolated side. External power can be connected to supply up to 2000mA current on isolated....
  • Galvanic isolation to the USB bus, supports SuperSpeed 5Gbps, hi-speed 480Mbps, full speed 12Mbps and Low speed 12Mbps.
  • 5kVrms signal and power isolation, Advanced ESD protection (20kV).
  • Ultra-quiet power rail isolation for less noise in highly sensitive applications (LT3045).
Check Stock

AEDIKO 4pcs Relay Module DC 5V Relay Switch 1 Channel Relay Board with Optocoupler Isolation Support High or Low Level Trigger

  • Fault-Tolerant Design: Fault Tolerant Design, Even if the Control Line is Broken, the Relay will not Operate.
  • All Interfaces of Relay can be Wired Out Through the Terminals Directly,Normally Open and Normally Closed.
  • Optocoupler Isolation:1 Channel Relay Board use Optocoupler Isolation that has Strong Driving Ability and Stable Performance ,The Isolation Circuit Prevent Damages to I / O Port by Relay Switch Current.
  • Jumper Design: The Relay Module has a Jumper That You Can Set Rather the Unit State Changes with High or Low Signal. Has Screw Terminals for Relay (NC,C,NO) and for Input.
  • Wide Application: DC 5V Relay Module Works Well with ARM /PIC /AVR /MCU/Raspberry/CNC Machine/ PS4 etc..
Check Stock

5v Relay Board Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
  • 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
  • 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
  • 【Wide Application】- These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
  • 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check Stock

Youngneer 5v Relay Board Raspberry Arduino Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
  • 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
  • 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
  • 【Wide Application】- These 5v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
  • 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check Stock

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check Stock

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

  • Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
  • Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
  • Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
  • This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
  • Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

ABB 1SVR730760R0500 CM-SFS.22S CURRENT MONITORING RELAY

  • Current sensing relay for monitoring electrical current.
  • Current carrying wire is routed through an aperture.
  • Electrical isolation between circuits (SPDT).
  • Variable trip point range with adjustable timer for stability.
  • UL recognized for safety and RoHS compliant for hazardous substances.
Check Stock

DSD TECH SH-G01A USB Isolator with ADUM3160 Chip 12M Blue

  • USB isolator:This USB isolator protect the communication interface between the host, such as a PC, and its peripheral.Through this isolator, the....
  • Maximum support 12Mbps:Support USB full speed 12 Mbps or low speed 1.5 Mbps . Please note: this USB isolator does not support 480 Mbps,So please don't....
  • Industrial grade: Built-in ADI ADUM3160 chip, support iCoupler technology. Signal isolation: 2500V.
  • Compatibility: This USB isolation adapter is compatible with Windows 7, 8, 10 and various Linux OS and Mac OS.
  • Warranty:DSD TECH provide a 1 year warranty and lifetime technical support for this USB isolator.if you have any questions, please feel free to....
Check Stock

Large Current 50A H-Bridge High-Power Single-Channel Motor Driver Module Semiconductor Refrigeration

  • 【H-bridge Driver Module】The drive uses a full H-bridge driver module full-bridge MOSFET driver chip and composed with very low internal resistance and high current. MOSFET H-bridge driver circuit, with strong drive and braking effect, signal isolation chip isolates motor drive effectively..
  • 【Effective Protection】With the microcontroller PWM signal isolation, effectively protect microcontroller..
  • 【Input Maximum】To achieve the motor forward and reverse rotation, two PWM input maximum 200kHz frequency..
  • 【Fully Compatible】Power indicator is schematically clear. The power supply voltage 5V to 15V. 3.3V to 12V, PWM level is fully compatible. High current 50A..
  • 【Warm Tips】Ffor your safety and protection of use, our product is tested to ensure trouble-free installation and performance, please rest assured to buy..
Check Stock

FTVOGUE Current Sensing Switch, Normally Open Self-Powered Current Sensing Relay, AC 0.5-50A (SZC25-NO-AL-CH)

  • Current sensing relay for monitoring electrical current.
  • Current carrying wire is routed through an aperture.
  • Electrical isolation between circuits (SPDT).
  • Internal transformer for scaling the current and a voltage reference circuit for a repeatable trip point.
  • UL Recognized for safety and RoHS compliant for hazardous substances.
Check Stock