Top Cylinder Heads For Ford 302

Head Stud Replacement Kit for 7.3L 1993-2002 Ford Power Stroke Diesel CP879

  • ...mpatibilities above to ensure accurate fitment..
  • ULTRA STRENGTH - XOTIC 7200 material properties allow for far greater tensile strength compared to 8740 chromoly steel head studs. Rated at 220,000 psi tensile strength. Threads rolled after heat treatment for optimum fatigue strength. Ample clamping strength prevents cylinder heads from lifting..
  • EASY INSTALLATION - Broached stud ends install & make cylinder head removal easier. Installation manual is included with drawn diagrams to ease the installation process. Head studs are designed to retain cylinder seal even with today's extreme high pressure turbo systems. These studs far exceed clamping forces provided by standard head bolts..
  • KIT INCLUDES - 36x Heads Studs, 36x Nuts, 36x Hardened Parallel Washer, 1x Fastener Assembly Lubricant & Instructions Manual. Black oxide finish protects from wear and tear. Hardened parallel washers allow for uniform load distribution and accurate torque readings..
  • WORRY-FREE PURCHASE - Xotic Performance is dedicated to offering LIFETIME WARRANTY and full money back guarantee if you aren’t satisfied. Rigorous quality inspections are undertaken to ensure premium product standards..
Check Stock

Distributor Cap Rotor and Spark Plug Wires Set - Ignition Tune-Up Kit - Compatible with 1984-1996 Ford F-150 4.9L 6-Cylinder

  • Compatible with or fits: (Note: Tall Cap) 1984 - 1986, 1996 Ford F-150 4.9L 6-Cylinder.
  • Compatible with or fits: 1995 Ford F-150 Special 4.9L 6-Cylinder.
  • Compatible with or fits: 1995 Ford F-150 Eddie Bauer 4.9L 6-Cylinder.
  • Compatible with or fits: 1993 - 1995 Ford F-150 XL 4.9L 6-Cylinder.
  • Compatible with or fits: 1993 - 1995 Ford F-150 XLT 4.9L 6-Cylinder | 1987 - 1992, 1996 Ford F-150 4.9L 6-Cylinder.
Check Stock

Sunex 2696 1/2-Inch Drive SAE 12-Point Driveline Socket Set, 7 Piece

  • Includes driveline sockets for Chevrolet, Chrysler, Dodge, Ford, GMC and Jeep models.
  • Remove and install driveline bolts, torque converters, cylinder heads, and 4x4 transmission casings.
  • SAE - inches: 5/16, 3/8, 7/16, 1/2, 9/16, 11/16, 3/4.
Check Stock

N351 Pushrod Guide Plates, Fits Ford, 5/16 Inch

  • Guide plates are specifically designed to work with the Small Block Ford V8 engine.
  • Made from durable steel with a natural finish.
  • Will work on 351N cylinder heads with the 5/16" push rods.
  • Comes in a set 8 eight to do the entire engine.
Check Stock

Tee Luv Men's Faded 1970s Ford Mustang Car Shirt (White) (M)

  • MAKE WAY FOR THE BOSS: Enjoy the nostalgia of the classic 1970 Ford Mustang Boss 302 against a checkered black graphic background - distressed and printed on the softest white cotton tee we could find..
  • EASY CARE TEES: This Ford Mustang Boss 302 design is licensed and screen-printed on a soft, high-quality 100% cotton t-shirt that goes from the washing machine to the dryer without losing shape, shrinking or fading. Graphic is intentionally distressed for a worn, vintage look..
  • NO FUSS SIZING: Tee Luv's Ford shirts feature a super comfortable adult regular fit, and are available in men's sizes: Small (S), Medium (M), Large (L), Extra Large (XL), XX-Large (XXL), or 3X-Large (3XL). True to size..
  • ALL DAY COMFORT: This lightweight auto tee pairs well with shorts for hot summer days, or with your favorite jeans for a comfortably casual night out. Tee Luv's retro car t-shirts feature a printed neck label for itch-free comfort..
  • OFFICIALLY LICENSED: Ford Mustang shirts sold by Tee Luv are guaranteed authentic and high quality, and are officially licensed by the Ford Motor Company. Proudly printed in the USA..
Check Stock

JEGS Non-Adjustable Rocker Arm Assembly | Fits Ford FE Engines | All-New & Ready To Bolt Down | Includes One Pair Of Rocker Arm Assemblies

  • BRAND NEW AND READY TO BOLT DOWN O.E. replacement unit.
  • FITS Ford FE engines including 352, 360, 390, 410, 427, 428 and others based on the same platform.
  • INCLUDES one pair of rocker arm assemblies to service two cylinder heads.
  • MUST HAVE FOR stock rebuilds or servicing heads.
Check Stock

A-Team Performance - Angle Plug Aluminum Cylinder Heads 64cc Chamber 205cc Intake Ports 2.020 Intake Valve 1.600 Exhaust Valve - Compatible with SBC 283 302 305 327 350 383 and 400 to 1986 Set of 2

  • Angle Plug Aluminum Cylinder Heads 64cc Chamber 205cc Intake Ports 2.020 Intake Valve 1.600 Exhaust Valve.
  • Compatible with SBC 283 302 305 327 350 383 and 400 to 1986 Set of 2.
  • These Bare Aluminum SBC heads have a 205cc Runner with 64cc combustion chambers with heart-shaped chambers..
  • Intake Valve Diameter: 2.020″ (up to 2.050 with machining, we do not offer this service).
  • Head also features a deck thickness of .625. Spring seats are cut to 1.550 diameters.
Check Stock

Remflex 3003 Exhaust Gasket for Ford V8 Engine, (Set of 2)

  • 1-1/8 inch width x 1-1/2" height Stock Square Port.
  • Ford V8 - 302 ('81-'95), 351 ('69-'97) Windsor, 1-1/8" x 1-1/2" Square Port, Manifold or Headers, 2/Set.
  • Heating and cooling of the exhaust system causes header and manifold flanges to warp resulting in gaps between the head and header which Remflex exhaust gaskets seal completely due to the thickness and compressibility of the 100 percent flexible graphite.
  • Remflex exhaust gaskets come in a standard 1/8 inch thickness and are designed to crush 50 percent allowing them to fill any pits or gaps in the flange surface up to 1/16 inch.
  • The aluminum cylinder head and steel header or manifold combination are configurations that readily cause gap issues in the mating flanges due to contraction and expansion of the dissimilar materials.
  • Remflex exhaust gaskets fill those gaps permanently.
  • There are no rubber binders or composite materials in Remflex exhaust gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.
Check Stock

Mophorn Complete Cylinder Head for 85-95 22R 22RE 22RE 2.4L SOHC Pickup 4Runner Speed

  • Perfectly Suited: This cylinder head perfectly fits the 1985-1995 Toyota 4Runner 2.4L SOHC 8v 4Cyl, 1985 Toyota Celica 2.4L SOHC 8v 4Cyl, 1985-1995 Toyota Pickup 2.4L SOHC 8v 4Cyl, Volkswagen 2005-2010 Jetta, 2012-2014 Beetle, 2006-2009 Rabbit..
  • Robust Iron Structure: Built from industrial-grade cast iron, our cylinder head is tolerant to the extreme pressure generated inside cylinders and resistant to high temperatures and abrasion. Give up disappointing cylinders, and we got what you are looking for..
  • Highly Stable ＆ More Efficient: These are nothing like those ordinary cylinder heads that bring you dissatisfaction. Ours features fantastic performance. Add this cylinder head to your engine, and drive at lower noise with a higher power transfer efficiency..
  • Fully assembled ＆ Tested: All our cylinder heads have been fully assembled, carefully packed, and are waiting to get into your hands. Replace your cylinder heads and start to experience the smooth ride you have been missing out on..
  • Widely Used: As a quality cylinder head, this has been used on lots of Toyota 2.4L SOHC 22R 22RE 22REC engines. Replace your old malfunctioning cylinder head with our newly improved one, and you will feel your engine running smoothly like never before..
Check Stock

Castrol 03060 GTX MAGNATEC 0W-20 Full Synthetic Motor Oil, Green, 5 Quart

  • Recommended by Ford Motor Company for use in the Ford GT, Shelby GT-500 and Boss 302.
  • This oil is compatible with other synthetic and petroleum based formulations.
  • Use according to owner guide recommendations.
Check Stock

E-cowlboy Crankshaft Positioning Tool for Ford 1993-newer 4.2L 4.6L 5.4L 6.8L Engines Crankshaft Holding Tool Timing Chain Installation Replace for Rotunda 303-448, T93P-6303-A, 6024 & 525219

  • ...Rotunda 303-448, T93P-6303-A, 6024 & 525219. Each part is manufactured to OEM specifications and testing..
  • Perfect Design — These engines are not Free Wheel engines, please Do Not rotate the crankshaft and/or camshaft when removing the timing chain and installing the cylinder heads. If it has "Jumped Timing", it will cause damage to the Valves and/or Pistons, requiring removal of the cylinder heads..
  • Easier Work — Must have tool for timing chain installation and adjustment! Easily install this tool over crankshaft and engine front cover alignment dowel. Align the crankshaft Woodruff key with the keyway on tool. It will position the crankshaft at top-dead-center (TDC) to correct the timing chain installation..
  • Superior Quality — Premium grade CNC machined heavy duty solid steel with black powder coated, strength and durability, anti-corrosion and anti-rust, anti-impact and anti-deformation. High precision and hardness to provide a much longer service life..
  • 100% Satisfaction Guarantee — If you're not 100% satisfied with our tools, simply return it for a fu....
Check Stock

Goblin Stud Online Slots Usa - Free Casino Slots Games

  • Fits Ford Tractor Models: 2000 3 cylinder, 2000 4 cylinder, 2031, 2100, 2110, 2111, 2120, 2121.
  • Fits Ford Industrial Models: 2030, 2130, 230A, 231, 233, 234, 250C, 260C, 333, 334, 335, 340.
  • Fits Case IH Models: 574, 3220, 3230, 385, 395, 4210, 4230, 4240, 454, 474, 484, 485, 495, 584.
  • Replaces Part Numbers: 313022, 81816580, 87780773, C5NN1107F.
Check Stock