Top Eurorack Clock Module

AOICRIE 2PCS DS3231 Real Time Clock Module RTC Clock Memory Module 3.3V/5V for Raspberry Pi (2PCS Yellow)

  • The RTC clock module is of complete clock calendar functions include seconds, minutes, hours, day, date, month and year timing , provide valid until the year 2100 leap year compensation.
  • The RTC clock module is of ±3℃ digital temperature sensor, and the timing accuracy kept at ± 5ppm (± 0.432 sec / day).
  • The RTC clock module has the characteristic of low power consumption, with 1 Hz and 32.768 kHz output.
  • The RTC clock module itself can be adapted to 3.3 V and 5 V system, with -40 ° C to +85 ° C temperature range, easy and convenient to use.
  • for Raspberry pi highest precision clock module DS3231, note board can also use this module..
Check Stock

4-Digit 7-Segment LED Display Clock Module with TM1637 IC Compatible with Raspberry Pi Arduino (Blue LEDs)

  • [Specifications] This is a basic 4-digit 7-segment Led display clock module, the LEDs are blue..
  • [Compatibility] This clock module uses TM1637 IC, it compatible with Raspberry Pi and Arduino.
  • [Easy to Use] The clock module connected to digital I/O via 2 pins..
  • [Easy to Install] This LED display designed with 4 mounting holes for easy installation..
  • [High Quality] The clock module is made of high quality electronic components, stable and reliable performance.
Check Stock

DORHEA 5PCS TM1637 0.56\ 4 Bits Digital LED Display Module with Clock Display 0.36 inch Common Anode Red Digital Tube Board with Cable for Arduino Raspberry Pi DIY Kits

  • The module is a 12 foot with a clock point four common anode tube (0.36 in.) display module driver IC is TM1637 driver IC TM1637, only two signal lines can make the MCU control 4 8 digital tube..
  • Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable. Control interface level can be 5V or 3.3V..
  • 4-digit LED display module with LED brightness adjustable and clock point, can be used to display decimal, letters and so on, suitable for uses in induction cooker, micro-wave oven and small household electrical appliance..
  • Total 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
  • The Positioning holes in this LED Display Module 4 Bits has 4 M2 screws positioning hole diameter is 2.2mm and the positioning of the module is easy to install with easy to achieve the inter-module combination..
Check Stock

Major Brands 8085A Microprocessor Unit, CISC, 8-Bit, HMOS, 3MHz, 40-Pin, CDIP, 15.37 mm W x 4.95 mm H x 52.96 mm L (Pack of 2)

  • AITIAO RTC clock module temperature range: -40 ° C to +85 ° C,the precision of digital temperature sensor is ±3°C.
  • the timing accuracy kept at ± 5ppm (± 0.432 sec / day).
  • AITIAO DS3231 High Precision RTC Clock Memory Module are CONVENIENT TO USE，because itself can be adapted to 3.3 V and 5 V system, no level conversion, it is super convenient.
  • Complete clock calendar functions include seconds, minutes, hours, day, date, month and year timing, provide valid until the year 2100 leap year.
  • Package Includes: 4Pcs DS3231 High Precision RTC Real Time Clock Module (battery are included).
Check Stock

Roland 500 Series Voltage Controlled Filter (SYS-505)

  • The SYSTEM-500 consists of Eurorack format modules that you can mix and match in any combination to create the ultimate Roland modular synthesizer..
  • Package Dimensions: 6.0 L x 3.5 H x 5.0 W (inches).
Check Stock

Behringer EURORACK RACK 19" Desktop/Rack-Mount Kit with Power Supply for 84 HP Eurorack

  • Desktop/rack-mount kit converts 19" rack into 84 HP Eurorack chassis.
  • Ideal for Behringer synthesizers and other Eurorack equipment.
  • Rugged aluminum chassis accommodates 84 HP rack-mounted and desktop setups.
  • Compact 4 HP power supply with two flying bus boards included (+12 [email protected] A, -12 [email protected] A, +5 [email protected] A).
  • Easy positioning of your modules with the included 52 sliding nuts.
Check Stock

4MS QCD Quad Clock Distributor V2 Eurorack Synth Module

  • Four CV-controlled Clock Divider/Multipliers.
  • Tap tempo button and five sync'ed clock outputs make the QCD perfect for head-of-the-chain "Master" clock module.
  • Tap clock output runs at the tapped tempo (even if other channels are being clocked externally).
  • Create complex rhythmic patterns by patching multiple channels into each other's Div/Mult CV and Reset.
  • Each of the four channels has an independent clock IN, OUT, Reset and Div/Mult CV.
Check Stock

Basic 16x2 Character LCD - RGB Backlight 5V

  • DRIVER IC: The module driver IC is for AIP650 (compatible for TM650), as well as supports multiple display characters..
  • 4 DIGIT 7 SEGMENT: The digital tube display module is designed for 4 digit 7 segment, with stable and reliable performance..
  • CONTROL INTERFACE: With 4 pins, SDA is bidirectional data line, SCL is clock line, GND is for ground line, and VCC is power supply..
  • COMPACT STRUCTURE: The LED digital tube module is exquisite and compact, which can be flexibly used in a variety of situations..
  • WIDE APPLICATION: This module is suitable for Raspberry Pi 3 B+ 4, for DIY electronic devices, toy cars and instrumentation etc..
Check Stock

Key Display for AVR 8-Bit Digital LED Tube 8-Bit TM1638 Module

  • DRIVER IC: The module driver IC is for AIP650 (compatible for TM650), as well as supports multiple display characters..
  • 4 DIGIT 7 SEGMENT: The digital tube display module is designed for 4 digit 7 segment, with stable and reliable performance..
  • CONTROL INTERFACE: With 4 pins, SDA is bidirectional data line, SCL is clock line, GND is for ground line, and VCC is power supply..
  • COMPACT STRUCTURE: The LED digital tube module is exquisite and compact, which can be flexibly used in a variety of situations..
  • WIDE APPLICATION: This module is suitable for 3 B+ 4, for DIY electronic devices, toy cars and instrumentation etc..
Check Stock

Synthrotek, Erica Synths Swamp DIY Kit

  • The SWAMP is a random CV and audio generator inspired by the famous Wiard Wogglebug module..
  • External audio input routed to ring modulator..
  • Clock input and output to sync the module to your modular system.
Check Stock

MEGA 2560 Starter Kit Ultra (100% Arduino IDE Compatible) w/ Battery Holder, Sensors, Modules, Resistor kit and Components (no Supply)

  • -Arduino MEGA R3 (generic high quality) + USB cable -6xAA Battery holder (9VDC) -WiFi ESP8266 module -Model Bluetooth Master / Slave HC-05 -Box with plastic cells (organizer of components) -Shield for prototypes + Mini-Breadboard -Large Breadboard (830 points ) -Dupont Cables 10 * Female-Female + 10 * Male-Female + 10 Male-Male -Cable Jumper for breadboard -6 Push Buttons with multicolored caps -Joystick Module type PS2.
  • -RC-522 RFID Module with white RFID Card and RFID Keychain -High-precision RTC Real-Time Clock Module DS3231 and EEPROM AT24C32 -PIR Presence Sensor HC-SR501 -Distance measurement module HCSR04 -Sound sensor detector module with programmable threshold -LM35 temperature sensor -Tilt detector module -Servo SG90 motor -Stepper motor (5V) -Motor driver module for stepper motor ULN2003.
  • 5V Active Buzzer -5V Passive Buzzer -LCD 1602 16 characters * 2 lines -LED Display Driver MAX7219 -LED Matrix Display of 8*8 -7 Segments Display 1 digit -7 Segments Display 4 digits -Simple Relay Module - Infrared Remote Control 38kHz - 38kHz Infrared decoder receiver (type 1838) - Infrared phototransistor (Flame sensor) - Infrared LED - Light sensor (Photoresistor).
  • -10 * LEDs 5mm Diffused RED -10 * LEDs 5mm Diffused GREEN -10 * LEDs 5mm Diffused YELLOW -5 *....
Check Stock

3D Printer Control Board Back EMF Protection Powerful 520Kb RAM USB Update Firmware ESP32 3D Printer Motherboard with WiFi for Serial Screen

  • SUPPORT VARIOUS SCREEN: This is a 3D printer main control board with onboard ESP32 wifi, supports for Marlin2.0 firmware, in addition to ordinary....
  • 32 BIT MICROPROCESSOR: Built in ESP32 DOWD V3 chip, for Xtensa dual core 32 bit LX6 microprocessor, supporting clock frequency up to 240MHz.
  • POWERFUL AND VERSATILE: The main board adopt ESP32 WROOM 32U module, embedded dual core 32 bit high speed MCU, the clock is up to 240MHz. And....
  • 8M BYTE CHIP: In addition, the module has a built in 8M byte Flash memory chip, which provides effective protection for more application scenarios.
  • BACK EMF PROTECTION: VEXP has designed a protection circuit for the back EMF generated by the stepper motor, which greatly reduces the damage to the....
Check Stock