Top Fitting Hose

Class A Customs | Under Mount 30 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit | UM-3000-BPK

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 20.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES: (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5”....
Check Stock

RIDGE WASHER Pressure Washer Gun with Extension Wand for Hot and Cold Water, Power Washer Gun with M22 Fitting, 5 Nozzle Tips, 40 Inch, 4000 PSI

  • Power washer gun is designed for hot and cold water in gas and electric pressure washer. Max Temperature for water is up to 100℃ ( 212°F ). Max Flow Rate is up to 5.3 GPM. Max Pressure is up to 4000 PSI..
  • This pressure washer wand fits pressure washer hose with M22 14mm or M22 15mm fitting. Generac, Ryobi, Briggs Stratton, Craftsman, Simpson, Karcher pressure washer hose has M22 14mm fitting. Sun Joe, Excell, MI-T-M, Stanley, Campbell, AR Blue, Cleanforce, Simoniz power washer hose has M22 15mm fitting. Please connect power washer wand to the hose directly if your hose has M22 14mm fitting. Please connect brass coupler between wand and hose if your hose has M22 15mm fitting..
  • The length of pressure washer handle is adjustable. Easy to change the length based on the purpose of cleaning. There are three length, 40 inch, 24 inch, 9 inch..
  • 5 spray nozzles have different spray angle (0, 15, 25, 40, 65 degree). Choose suitable nozzle based on the purpose of cleaning. Such as watering flowers or plants, washing car, fence or roof. Universal 1/4’’ quick connector is also designed for turbo nozzle, surface cleaner, water broom, undercarriage cleaner, pivoting coupler, foam cannon, pressure washer sandblasting kit, gutter cleaner attachment..
Check Stock

PWACCS Pressure Washer Swivel, M22 14mm Swivel Joint, Stainless Steel, 5000 PSI

  • UNIVERSAL CONNECTORS: Pressure washer swivel convert metric M22 14mm male to M22 female thread fitting. Easy to connect and release. Pressure washer swivel joint can connect gun and hose, hose and hose easily. Pressure washer fittings fit most brand of pressure washer hoses and guns..
  • 360 degree rotation freely, pressure washer swivel fitting helps keep the pressure washer hose from tangling and getting kinked when Spraying. The kinks unfolding as you move around. It will solve hand fatigue due to the pressure built up between hose and gun..
  • Pressure washer gun swivel is made of high quality stainless steel, durable, wear resistantand, resistance to corrosion, long service life..
  • Pressure washer hose swivel’s Max Working Pressure: 4500 PSI. Max Flow Rate: 30.0 GPM. Max Working Temperature: up to 120℃, 250°F..
  • If the Kink free gun to hose fitting have any questions, please contact us at first time. We provide a service of quick reply within 24 hours..
Check Stock

Bonbo Fuel Gas Cap with Brass Hose for Honda EU2200i EU1000i EU2000i EU3000i Handi, Champion 2000watt, Westinghouse 2200watt WH2200iXLT Generators, Upgrade Extended Run (Red)

  • Application - This fuel gas cap can be widely used in Honda EU2200i EU1000i, EU2000i, EU3000i Handi, Champion 2000watt, Westinghouse 2200watt WH2200iXLT generators..
  • Function - As a fixed connection between plastic or rubber hose and pipe, this gas cap with brass hose fitting helps you add gasoline into generator within a safe distance, ensuring seal tight and no leakage..
  • Design - The brass hose fitting has a 1/4" male end for connecting to threaded pipe, conforming to National Pipe Thread (NPT) standard and the barbed fitting for a hose is equipped with a 1/4" inside diameter..
  • Material - The gas cap is made of premium CNC billet aluminum, finishing with stylish anodized red coat. And the hose fitting is made of top high quality and wear resistance brass, performing well even under extreme conditions..
  • Satisfaction Guarantee - Bonbo aims to provide best products and services for our customers. If you receive broken or defective gas cap and brass hose fitting, please contact us any time, we will compensate you with 1 year warranty or 30 days full refund..
Check Stock

EVIL ENERGY 6AN PTFE Hose End Fitting 90 Degree Black for PTFE Hose Only

  • Please Attention that the 6AN PTFE hose end can be work with PTFE fuel line ONLY..
  • Thread Size of 6AN PTFE Fitting is 9/16-18UNF and work with PTFE fuel line(Hose ID: 0.31 inch OD: 0.43-0.47 inch)..
  • The PTFE hose end is reusable, just  replace a new ferrule if you reinstall the fitting..
  • EVIL ENERGY Provide plently kind of fuel fittings, Swivel, push-on lock, PTFE hose end and other fitting adapters..
  • Warrany: EVIL ENERGY provide PTFE hose end 6-month warranty. We value your shopping experience and strive to offer a high-quality product and service..
Check Stock

YuanTenhwy 3 PCS 3/8 10mm Brass Hose Barb Tee Fittings With 9 PCS Stainless Steel Clamps For Air/Water Hose Splicer 3-Way-T…

  • 【Size】: The outer diameter of Hose barb fitting is 3/8 inch (10mm).
  • 【Packing list】: 3 PCS of 3-way(Type T) Hose barbs fitting with 9 PCS of stainless steel hose clamp.
  • 【Material】: The hose barbs fitting is made of brass, and the hose clamp is made of stainless steel.
  • 【Features】: corrosion resistance, dimensions in line with standards, and overall smooth without burrs.
  • The solid barb and hose clamp ensure that the hose and the Hose barb fittings are well sealed during connection, and are not easy to leak.
  • 【Application Scenarios】：It is applicable to pipeline installation and maintenance, and is often used to assist in the transportation of gas, water or oil. However, federal laws do not allow the installation of these fittings for drinking water in the United States and its territories..
Check Stock

WATERWICH Fuel Injection line Hose 6AN 3/8'' 25FT PTFE EFI LS Fitting Kit Stainless Steel Braided

  • ...i. Bursting Pressure(psi) : 10000psi. PTFE tube fuel hose length: 25Ft, inner diameter: 0.3inch (8mm), outside diameter: 0.47inch (12mm) . Please make sure the dimension, pressure and temperature range before purchase!.
  • 4.Package Included: 25Ft 6AN braided fuel injection line hose , fuel PTFE tube and aluminum alloy fitting adapter: 6pcs 6AN PTFE straight hose end, 2pcs 6AN PTFE 45 Degree hose end, , 2pcs 6AN to 3/8" hose adapter fitting, 2pcs 6AN to 1/4"NPT hose adapter fitting , 1pc AN6 to 3/8"quick disconnect male, 1pc 6AN to 5/16" hose adapter fitting..
  • 5.Professional installation recommended: PTFE hose relatively hard, it can't be bend and folding in half. Nylon and stainless steel braid for excellent flexibility and resistance to abrasion. Outer nylon braided has excellent inflaming and safer to use..
Check Stock

Class A Customs | 25 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2500-BPK-PUMP

  • 25 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS 33.5” Longest Length (not including fittings) x 10” x 17”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID V....
Check Stock

Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP

  • 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check Stock

Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP

  • 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Check Stock

JoyTube 5 Pcs Hose Barb Fittings 3/8 Barb to 1/2 NPT Male Thread Brass Metals Adapter Connector with Hose Clamp

  • Brass barbed hose fitting is for connecting 3/8" barb hoses, NPT male end used to connect 1/2" NPT female pipes fitting..
  • Made of high quality solid brass, firm and durable, providing high resistance to abrasion and corrosion, low magnetic permeability, ductility at high temperatures, which can withstand up to -40 to +160 degrees F..
  • When used with a hose clamp or crimp sleeve or ferrule, the hose barb fitting can creates a better tight seal..
  • Brass barbed fitting kits can be used with PVC, PU, Rubber hose or tubing, Which can apply to water, gas, oil and fuel as well as air tools..
Check Stock

10 Foot Long Dust Collection Power Tool Hose Kit for Multiple Types/Brands of Power Tools and Work Shop Vacuums with Threaded Fittings

  • The smaller diameter 1-3/16" O.D. (Outside diameter) flexible dust collection power tool hose moves freely when connected to your power tools and vacuum. This gives you the ability to plug into different tools to add dust collection at a moments notice. The hose and its specialized fittings work with multiple power tools, workshop vacuums, jigs and other tools around your woodworking shop or work shop..
  • The small rubber fitting threads on to the end of the hose and is ideal for connecting random orbital sanders, palm sanders, biscuit joiners or any other power tool with smaller dust collection ports. The small thread-on rubber fitting has a 1 inch I.D. with a 1-3/16 inch taper up to 1-1/4 inch O.D. This kit will also work with popular tools like the K4 and the K5 Pocket Hole Jig. Using this hose with your tools will keep your shop cleaner and can be quickly coiled up for easy storage.
  • The large thread-on rubber fitting has a 1-1/2 inch I.D. with a 1-13/16 inch O.D. which works on many other power tools. The rigid plastic vacuum Plug-in Adaptor has a 2-1/4 inch taper up to 2-5/16 inch O.D. The adaptor is designed to plug into most standard workshop vacuum ports. The Plug-in Adaptor conveniently threads onto the power tool hose so it will never slip off!....
Check Stock