Top Gold plate Pcb

YMDK Aluminum Brush Finish ANSI Anodized Positioning Board Plate Plate-Mounted for GH60 PCB GK61 GK61x Hot Swap PCB

  • Package Included: 1x plate.There is no screws and copper stand included..
  • Pls note: Original GK61 GK61x GK61xs plastic case can't use this plate directly.Need to replace a GH60 compatible case.
  • This plate is anodized brush finished.It can only use with plate mounted stabilizers.
  • If you use with GK61 /GK61x PCB,can just mount 4-5 switches into the plate corner and then plug to PCB socket totally.After the plate PCB fixed,then mount other switch in 1 by 1 is ok.At last screw plate PCB togehter to GH60 size case is ok with the screws in your case..
Check Stock

Gikfun Solder-able Breadboard Gold Plated Finish Proto Board PCB DIY Kit for Arduino Pack of 5PCS GK1007

  • This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in....
  • Breadboard PCB for any type Raspberry Pi GPIO.
  • Gold plated finish prevents oxidation, High quality Gold finish for easy soldering.
  • All holes are through-plated for strength.
  • Adaptable with a variety of MCU boards. Compatible with Arduino Nano, Pro Mini, NodeMCU, etc..
Check Stock

DUROCK V2 PCB Mount Screw in Stabilizers, Translucent Smokey Keyboard Stabilizers with 2u 6.25u 7u Wires, Keycap Stabilizers Mechanical Keyboard Stabilizers (V2 Smokey 60/87 Kit)

  • DUROCK V2 Stabilizers are PCB mount screw-in Stabs that feature a patent design and precision upgrade models to avoid wire drop out..
  • The V2 Stabs Stem / Sliders are pre-clipped design, do not require any clipping for fast & easy set up..
  • Well selected Premium Polymer Nylon housings, all the Stainless Steel Wires and hardware are sourced from Korea and with real gold coating..
  • Translucent Smokey V2 housings and the gold-plated Wires set gives your board an elegant and golden edge..
  • DUROCK Stabilizers V2 Compatible with PCBs that use "screw-in" or "PCB Mount" stabilizers. ( Washers, both 6.25u and 7u spacebar Wire included ).
Check Stock

YMDK GK61x GK61xs GK64x GK64xs Anodized Aluminum CNC Case (Only Aluminum Case)

  • Package Included: CNC Case + Rubber Feet + Screws.
  • New GK61x GK61xs GK64x GK64xs plate and PCB can install in directly..
  • Old GK61 GK64 plate can't use since the size is bigger than normal 60 case.You can just replace a GH60 size customized plate is ok.The plate need to be compatible with GK61 PCB..
  • How to judge old and new edition: Old GK61 GK64 PCB is white and only support single 6.25u space New GK61x GK61xs GK64x GK64xs PCB is black and can support split space and single space at the same time..
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.If little keys not working,check the switch pin whether it's bent at first.Especially Kailh switches.
Check Stock

SinLoon M.2(NGFF) Key M NVMe SSD Extension Cable Extender PCIe3.0 x4 Full Speed 12.6inch SSD Extension Cable (32cm)

  • 【M.2 NVMe Solid State Drive Extension Cable 】Allows you to extend M.2 NVMe slot outside of the laptop..
  • 【Maximum Transmission】PCIe3.0 x4 full speed.The maximum transmission rate is 32Gbps (Max.)..
  • 【Product advantages】If your Chassis is too small, the SSD will soar to 75°C when playing games. You can use this M.2 NVMe SSD extension cable to place it next to the fan and keep it at about 30°C offers you smoother experience..
  • 【Durable and strong】SSD Extension Cable uses high-quality materials, PCB workmanship precision, gold finger gold content is sufficient, gold-plated foot has good electrical conductivity, which can reduce the blue screen of the crash caused by the increase of oxidation and rust resistance. The signal transmission is stable at full speed and there is no compatibility problem..
  • 【Features】M.2 NVME SSD extension cable is fastened with screws and hex nuts. The product is strong and reliable, resistant to pulling, anti-interference, and will not be broken. The nail problem. The wire can be bent and folded without affecting the use. PCB long design to make the board easier to install, reducing the chance of damage..
Check Stock

The Warhol Incident (Alexis Parker Book 2)

  • Package Included:Plastic Case + Feet + Stabilizers + GK64x Hotswap Type C PCB + Plate + Cable + Removal Tool + Space Module.
  • Pls note:GK64x is wired kit.The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place.If some keys not working after plugging,please check whether your switch pin is bent or not.Make sure plug in 90 degree above plate.
  • This kit support 6.25u space and split double space.This plate is screwed to case directly.So if you want to replace normal GH60 case,you need to replace a non -replacable GH60 size plate is ok..
  • PCB has RGB presoldered,it's under per switch.This kit need to use Cherry MX switches and clones,optical switches is not supported.
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.
Check Stock

Harby Centauri Overdrive and Boost Guitar Effects Pedal

  • A modernized, yet highly accurate circuit tribute of the legendary Klon Centaur overdrive pedal.
Check Stock

Gikfun Mini Solderless Breadboard 400 Tie-points + 2xPCB Solder-able Breadboard + 2.54mm 10Pin Jumper Wires Male to Male DIY Kit for Arduino EK8473

  • This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place..
  • 1 x Mini Solderless Breadboard 400 points, Size:8.3cm x 5.5cm..
  • 2 x PCB Solder-able Breadboard, Gold plated finish prevents oxidation, High quality Gold finish for easy soldering. All holes are through-plated for strength..
  • 10Pin 2.54mm Male to Male Jumper Wires Male to Male, 20CM..
Check Stock

Switch Sound Dampeners Sheet Soft Landing Pads Dimple Foam Sponge (87 Layout)

  • 【Product Function】Eliminating cavity sound, increasing sound thickness and reducing keyboard resonance..
  • 【Eliminate Keyboard Noise】Between the installation and the PCB and the steel plate, the steel plate and the PCB are used for clamping, no adhesive is required, and the light position is not affected. It fills the entire keyboard, the soud is thicker , the resonance of the plastic keyboard and the cavity sound are eliminated..
  • 【Switch Sound Dampeners Sheet】This product is a Switch Sound Dampeners sheet, which is placed between the keyboard's circuit board (PCB) and the positioning board. It is a must for keyboard lovers to DIY your keyboard..
  • 【3mm Thickness】Most of the silencer pads are designed based on a standard 1.5mm positioning plate. Due to the processing accuracy of the plate, the space between the PCB and the positioning plate ranges from 3mm to 3.5mm. Regardless of whether the keyboard switch is welded or hot-plugged, the 3mm silencer pad is the best choice..
  • 【Warm Tips】This silencer pad is measured and drawn according to the keyboard entity. It is not produced by the original manufacturer and cannot be guaranteed to be fully fitted. Some of the holes, gaps, and circles may be caused by too many models and brands of the sam....
Check Stock

RUNJRX Keyboard Stabilizers Screw-in Stabilizers Shaft Mechanical Keyboard PCB Mount Transparen Screw-in Stabilizers 7U 6.25U 2U (60/87, Whiteness)

  • APPEARANCEThe translucent case makes your keyboard more beautiful, the gold-plated balance bar and gold-plated screws increase the oxidation resistance and extend the use time..
  • REASONABLE MATCHWe provide players with a screwdriver, easy to assemble and disassemble, also includes eva foam, according to their needs arbitrary cut, put into the keycap behind, effective noise mitigation, easy to install..
  • PACKAGE INCLUDINGScrewdriver x 1, stabilizer 2U x 4, stabilizer 6.25U x 1 , 7U balance bar x 1, screw x 10, high density eva custom foam x 1..
  • Hand FeelNo stuck keycaps, smooth feel, comfortable rebound strength..
  • AttentionThe RUNJRX Keyboard Stabilizer is a screw-in stabilizer for custom keyboard PCB..
Check Stock

Gardner Bender GSW-26 Electrical Door Switch, SPST, Normally On- Mom OFF, 16 A/125V AC, (Repl. for GSW-SK)

  • Tealio switches come in 1 variant. The spring weight is rated at "bottom out" force, not actuation! Our Tealio switches have been tweaked with wobble reduction and improved smoothness compared to regular Gateron linears..
  • 67g - Transparent, Light Teal-Blue Stem, PCB Mount [Linear].
  • Please note that PCB mounted switches can still be used in many plate mounted keyboards. As long as your PCB underneath has 2 extra holes next to the center post, it will support PCB Mounted switches and add extra rigidity to your build. If your PCB does not have the extra holes, then you can simply cut the small plastic legs off to make them Plate-Mount!.
Check Stock

Skyloong 64 GK64 GK64x RGB Hot Swap Programmable Wired Case PCB Plate Cherry MX Keyboard DIY kit Replacable Space

  • Package Included:Plastic Case + Feet + Stabilizers + GK64x Hotswap Type C PCB + Plate + Cable + Removal Tool + Space Module.
  • Pls note:GK64x is wired kit.The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place.If some keys not working after plugging,please check whether your switch pin is bent or not.Make sure plug in 90 degree above plate.
  • This kit support 6.25u space and split double space.This plate is screwed to case directly.So if you want to replace normal GH60 case,you need to replace a non -replacable GH60 size plate is ok..
  • PCB has RGB presoldered,it's under per switch.This kit need to use Cherry MX switches and clones,optical switches is not supported.
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.
Check Stock