Top Gpio Interfaces

risingsaplings rpi gpio io Expansion Extension Module Board for Raspberry Pi 3 2 Pi Model B+ 4 Zero

  • This GPIO extension board is compatible with Raspberry Pi 3, Pi 2, Model B / B+, ZERO and ZERO-W. (For ZERO you need to soldered a 2x20pin header in your Raspberry Pi ZERO).
  • GPIO 1 to 3: 1 row GPIO ports could expanded into 3 rows GPIO ports..
  • All pins are marked with function names..
  • Come with 4pcs double-screw bolt, 8pcs Screws..
Check Stock

DORHEA 10PCS ESP-WROOM-32D ESP32 Bluetooth and WiFi Low Power Module integrates ESP32-D0WD Generic Wi-Fi+BT+BLE MCU Modules for Voice Encoding Music Streaming and MP3 Decoding

  • ESP32-WROOM-32D are powerful, generic Wi-Fi+BT+BLE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding..
  • The sleep current of the ESP32 chip is less than 5 µA, making it suitable for battery powered and wearable electronics applications..
  • ESP32-WROOM-32D integrate a 4 MB of external SPI flash. The integrated SPI flash is connected to GPIO6, GPIO7, GPIO8, GPIO9, GPIO10 and GPIO11. These six pins cannot be used as regular GPIOs..
  • Flash integrated on the module and are not recommended for other uses..
Check Stock

5Pcs GPIO Ribbon Cable for Raspberry Pi Male to Female 40pin Breadboard Jumper Wire Computer Accessories 20cm(Male to Female)

  • The GPIO cable can be connected to a 3.5 inch display for easily use.
  • Professional designed for Raspberry Pi male to female GPIO cable.
  • Possess 20cm length and 40pin in total, enough to meet your demands.
  • This cable wire can be used to extend the GPIO of for Raspberry Pi.
  • GPIO wire can be connected to T board, breadboard and other operations.
Check Stock

WayinTop RPi GPIO Breakout Expansion Kit for Raspberry Pi 4B 3B+ 3B 2B B+, T-Type GPIO Expansion Adapter Board + 830 Tie Points Solderless Breadboard + 40pin GPIO Flat Ribbon Cable + 65pcs Jumper Wire

  • 【Updated Starter Kit for Raspberry Pi】This is a updated Assembled starter kit for for Raspberry Pi 4B/3B+/3B/2B/B+, including GPIO Adapter Board with Wiring Diagram Card, 40pin GPIO Rainbow Fat Cable, 830 Tie Points Solderless Breadboard and 65pcs Jumper Wire..
  • 【GPIO Adapter Board with Wiring Diagram Card】You can connect much version raspberry of the board to various sensors and electronic components with the GPIO extension board..
  • 【40pin GPIO Rainbow Fat Cable】IDC 40pin Male to Female Ribbon Cables Kit flat GPIO Cable.
  • Material: High-quantity copper soft wire material for safe and durable.
  • Easy assembly:The cables can be separated to form an assembly wires to support non-standard odd-spaced headers to complete other tests..
  • 【830 Tie Points Solderless Breadboard】made of high quality ABS plastic, each row and columns has corresponding letters and numbers, reduce the mistake handling, with self-adhesive tape on back and multiple links to buckle..
  • 【65pcs Flexible Jumper Cables】Flexible, durable, reusable, easy to connect and disconnect.
  • 4 Kinds of length: 12cm(49pcs), 16cm(8pcs), 20cm(4pcs), 24cm(4pcs).
  • these jumper cable wires can connect each other through the pin connection, do not need welding, can fit for fast circuit....
Check Stock

HiLetgo GPIO Expansion Board Raspberry Pi Shield for Raspberry PI 4B/3B+ With Screws

  • Raspberry Pi 4B/3B+ GPIO Shield Expansion Board.
  • Multifunction GPIO Extension Board 1 to 3 Port DIY.
Check Stock

MakerFocus Raspberry Pi 4 GPIO Expansion Board Breakout GPIO Screw Terminal Hat Compatible with Raspberry Pi 4b 3b+ 3b 2b b+ Raspberry Pi Zero and Zero W

  • User manual: Please get the link from the product description below.
  • Easy to Assemble - This is a very beautiful screw terminal expansion version, which is expanded for the pins of the Raspberry Pi. Our raspberry pi hat is convenient for everyone to connect when doing electronic experiments..
  • Observe GPIO Status - The status information of the pin is displayed. When the GPIO pin is operated and effective in the terminal, the LED matrix on the right side of the terminal will display the status of the GPIO pin, and some distinctions are made in the color selection of the LED lights..
  • Fine Terminal Pinout - There is the pin out information of the GPIO pin on the top of the terminal and on the side..
  • Different Color LED Indicators - For example, the 5V power light is red, while the 3.3V power light is pink, the light of the special function pin is dark blue, and the indicator light of the ordinary GPIO pin is light blue.
Check Stock

REXQualis RPi GPIO Status LED & Terminal Block Breakout Board HAT for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

  • The item has been soldered and assembled. Support for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B.
  • GPIO status LED and power 5V / 3.3V indication. GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
Check Stock

kuman RPi GPIO Breakout Expansion Board + Ribbon Cable + Assembled T Type GPIO Adapter 20cm FC40 40pin Flat Ribbon Cable for Raspberry Pi 3 2 Model B & B+ SC05

  • Assembled RPI GPIO with 8" 40 pin ribbon cable for Raspberry Pi 3B, Raspberry Pi 2 model B, Raspberry Pi 1B+, Raspberry Pi 1a+, Raspberry Pi zero w, Raspberry Pi zero.
  • 40 pins are labeled for easy prototyping.
  • Gpio adapter plus for Raspberry Pi B+, Raspberry Pi 2, Raspberry Pi is not included.
Check Stock

Treedix 3pcs GPIO Reference Board Pinout Plus for Raspberry Pi A+, B+, 2, 3, 4

  • This reference board is a very convenient tool to determine the position and function of each pin, which can make it very easy to connect the wire to the Raspberry Pi GPIO.
  • One side of the reference board shows the position, and the other side shows the GPIO number. You can view all the different pin labels of the 2×20 GPIO connector on the Raspberry Pi. By placing it on the connector or next to it, you can quickly check if any wires or components are properly connected.
  • Material: Raspberry Pi GPIO Plus reference pinout is made of glass fiber, and the holes of the reference plate are gold-plated Length: 60.2 /2.37in, width: 20.1mm/0.79in 100% high quality..
  • Use this reference guide to easily connect wires and components to your Raspberry Pi.
  • Compatible with Raspberry Pi models A+, B+, 2, 3 and 4.
Check Stock

Ingcool Raspberry Pi Pico Microcontroller Board with Pre-soldered Header Low-Cost, High-Performance,Based on RP2040 Chip, Dual-core Arm Cortex M0+ Processor,Flexible Clock Running up to 133 MHz

  • Raspberry Pi Pico is a low-cost, high-performance microcontroller board with flexible digital interfaces..
  • Raspberry Pi Pico Board incorporates Raspberry Pi's own RP2040 microcontroller chip, with dual-core Arm Cortex M0+ processor running up to 133 MHz, embedded 264KB of SRAM and 2MB of on-board Flash memory, as well as 26x multi-function GPIO pins..
  • For software development, either Raspberry Pi's C/C++ SDK, or the MicroPython is available..
  • There're also complete development resources and tutorials to help you get started easily, and integrate it into end products quickly..
  • This is a Raspberry Pi Pico with Pre-soldered Header,it is easier to connect with another items..
Check Stock

GPIO Status LED Terminal Block Breakout Board for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

  • GPIO status LED and power 5V / 3.3V indication..
  • GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
  • Support for Raspberry Pi A+, 3A+, B+, 2B, 3B, 3B+, 4B.
  • Terminal block pitch 3.5mm, wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion pin header, height 8mm..
  • Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not include Raspberry Pi module).
Check Stock

sb components Raspberry Pi Pico GPIO Expansion Board, Multi-Purpose GPIO Expansion for Raspberry Pi Pico

  • Raspberry Pi Pico GPIO Expansion Board is used to break out all the pins and power of the Raspberry Pi Pico development board via male or female headers.
  • Pico GPIO Expansion Board allows the user to connect it to other components with the help of a jumper wire.
  • It has been designed to enhance the learning experience for the user.
  • GPIO Expansion Board is specifically made to work with the Raspberry Pi Pico Board.
  • Compatible with all the variants of Sensors/Modules.
Check Stock