Top Ground Shaft For Linear

LML9B 9mm Linear Rail Mini Bearing Steel Guide Rail Slide Rail+ Slide Block Variety Length (150mm)

  • Package Content:2 x linear rail shaft rod + 4 x SBR12UU.
Check Stock

Rudedog USA 5003 Lock Collar with Grommet Kit. For 3/4\ Hex Bar only

  • Used for shaft fixing and positioning, SBR linear rail stopper, for DIY CNC Routers Lathes Machine..
  • Design fully engages the shaft. Easily installed.
  • High quality aluminum alloy material, lightweight, surface oxidation resistant and corrosion resistant, durable and strong..
  • The shaft can be clamp-on tightly by set screw, the shaft will not be damaged.
Check Stock

Amprobe DGC-1000A Clamp Ground Resistance Tester

  • Ground resistance tester for measuring ground resistance, current, and continuity in multi-grounded systems.
  • True RMS meter provides accurate readings when measuring linear or non-linear loads where the current or voltage has a sinusoidal or nonsinusoidal waveform.
  • Clamp-on head to measure resistance on a ground rod without the use of additional ground rods and without disconnecting the grounds under test.
  • Measures ground resistance from 0.025 to 1,500 ohms and AC current up to 10A.
  • Safety rated to European Standard 61010-2-32 Category III 300V, Category II 600V.
  • Continuity beep if the resistance is lower than 40.00 Ohms.
Check Stock

CNC Parts 2Pcs SBR20-1200mm Linear Rail Guide with 4Pcs SBR20UU Bearing Block for Fully Supported Linear Rail Length 47.2 inch(1200mm)

  • 1200mm Linear Rail Slider Set: This linear rail set is of 2Pcs SBR20 1200mm/47.2 inch linear rail and 4Pcs SBR20UU Block.
  • Sports performance under high load or long stroke, high precision, smooth moving, low friction, high performance and easy to mount & dismount.
  • Cooperate with open linear bearing to ensure excellent sports performance, and metal linear bearing, its more durable than Plastic linear bearing.
  • Perfect combination of main axle and aluminum alloy support, which nicely stabilizes the original rail. Premier quality bearing blocks moves smoothly while using.
  • Linear motion ball bearing set is widely used for digital 3D coordinate measuring equipment such as precision equipment or special machinery industry. Suitable for kinds of electronic equipment/guide bar, drive shaft, and pillar.
Check Stock

Linear Rail Guide 20mm 2Pcs SBR20-1500mm(59.1 inch) Linear Slide Rail + 4Pcs SBR20UU Bearing Linear Guide Slide Blocks for CNC Machine

  • 1500mm Linear Rail Slider Set: This linear rail set is of 2Pcs SBR20 1500mm/59.1 inch linear rail and 4Pcs SBR20UU Block.
  • Sports performance under high load or long stroke, high precision, smooth moving, low friction, high performance and easy to mount & dismount.
  • Cooperate with open linear bearing to ensure excellent sports performance, and metal linear bearing, its more durable than Plastic linear bearing.
  • Perfect combination of main axle and aluminum alloy support, which nicely stabilizes the original rail. Premier quality bearing blocks moves smoothly while using.
  • Linear motion ball bearing set is widely used for digital 3D coordinate measuring equipment such as precision equipment or special machinery industry. Suitable for kinds of electronic equipment/guide bar, drive shaft, and pillar.
Check Stock

Linear Rail Kits 2Pcs SBR20-2000mm(78.7 inch) Linear Rail with 4Pcs SBR20UU Bearing Linear Guide Slide Blocks for Fully Supported Linear Rail

  • 2000mm Linear Rail Slider Set: This linear rail set is of 2Pcs SBR20 2000mm/78.7 inch linear rail and 4Pcs SBR20UU Block.
  • Sports performance under high load or long stroke, high precision, smooth moving, low friction, high performance and easy to mount & dismount.
  • Cooperate with open linear bearing to ensure excellent sports performance, and metal linear bearing, its more durable than Plastic linear bearing.
  • Perfect combination of main axle and aluminum alloy support, which nicely stabilizes the original rail. Premier quality bearing blocks moves smoothly while using.
  • Linear motion ball bearing set is widely used for digital 3D coordinate measuring equipment such as precision equipment or special machinery industry. Suitable for kinds of electronic equipment/guide bar, drive shaft, and pillar.
Check Stock

Clarostat 100K OHM MODPOT Linear Taper Potentiometer 1W 1 Watt 10%

  • .25″ “Flat D” shaft diameter, .35″ (9.5mm) length to allow for a knob if desired.
  • Shaft Length: 22mm (7/8″), Bushing Length:12.5mm (0.50″), Total Shaft Length 1.50″.
  • Body is .63″ square, Mounts in a .375″ hole.
Check Stock

2.62 x 2.62 Lg., Cross Roller Slide Assembly, Linear Motion, Del-Tron (1 Each)

  • 1. Chrome plating linear shaft, high hardness, lasting to use..
  • 2. Standardized processing aluminum alloy sliding block, with strong interchangeability..
  • 3. Built-in high precision linear bearings allows the slide block to move smoothly with little resistance..
  • 4. Oxidation surface treatment makes the sliding block beautiful, rustproof and more durable..
  • 5. The linear slide rail has pre-drilled holes for easy mounting..
Check Stock

Linear Rail SBR12 1000mm 12mm CNC 2PCS Linear Rail Slide Guide Shaft 4PCS SBR12UU Bearing Blocks for Automated Machines and Equipments

  • LINEAR RAIL KITS: 2 pieces of linear rail 1000 mm/39.37" long rail shafts and 4 Pieces SBR12UU blocks. Sliding blocks to be used cooperatively with rails..
  • EASY TO INSTALL: Aluminum support rail with pre-drilled holes for ease of mounting.Suits X, Y, Z axis..
  • ADVANTAGE: Premier Linear Guiding System.The support rail unit provides maximum rigidity and stiffness to the shaft throughout the whole stroke, and ensure the performance of the unit..
  • HIGH-QUALITY STEEL MATERIAL: CNC parts linear rails are made of carbon steel, linear bearings are made of quality bearing steel with aluminum alloy housing. Surface chrome plating treatment makes it anti-rust, durable, and extremely hard..
  • WIDELY USED: It is widely used in linear motion system. Such as, punch, tool grinding machine, automatic cutting machine, printer, card sorting machine, food packing machine, other sliding parts on industrial machinery..
Check Stock

10pcs LM12UU 12mm Linear Motion Ball Bearing Bushing for 12mm Rod 3D Printer CNC Parts

  • [SIZE] - Model: SCV13UU, 44 x 20.9 x 30mm Metric Double Seal Linear Bearing, 13mm Nominal Shaft Diameter.
  • [USAGE] - Linear bearings are part of linear motion systems, often used in conjunction with cylindrical shafts or guideways..
  • [FEATURES] - These ball bearing with two rubber dust sealed to prevent ingress of dirt, water and foreign matter.
  • Aluminium alloy housing to provide high strength and stiffness..
  • [CAPABILITY] - Static Load Capacity (Cor): 784N, Dynamic Load Capacity (Cr): 510N (Recommended load is 80% of rated load, not to exceed rated load.).
  • [APPLICATIONS] - Mechanical slides, 2-axis and 3-axis tables, linear tables, 3D printers, ect..
Check Stock

Twotrees Linear Motion Guide 10mm x 350mm (0.393 x 13.78 inches) Case Hardened Chrome Plated Linear Motion Rod Shaft Guide - Metric h8 Tolerance (2 pcs)

  • The material is carbon steel, which is very suitable for linear motion rod..
  • The surface has been chrome plated to enhance the hardness..
  • Chamfer on both ends, easier to install linear bearings and won't hurt fingers when installing it..
  • Round steel shaft for use with linear support blocks and closed type slide units in linear motion applications.
  • Diameter 10mm, tolerance -0.005mm to -0.03mm ( 9.995mm - 9.97mm), length 350mm, tolerance ± 0.5mm ( 349.5mm - 350.5mm )..
Check Stock

WMYCONGCONG 20 PCS B10K 10K Ohm Knurled Shaft Linear Rotary Taper Potentiometer with Black Knob(WH148) Kit

  • 10k Potentiometer: Single linear rotary taper potentiometer, B10K, 3 terminals, single linear, with standard knob, meet your adjustment needs..
  • Value Marked: B10K Ohm knurled shaft linear rotary taper potentiometer, marked clearly for easy recognition, with nuts, washers and caps for Arduino..
  • Type: single linear(with nuts and washers).
  • Application: Ideal to be used for volume control in audio applications, such as guitar, amplifier, audio, lamp and other audio equipment. Handy and practical pot kits for your DIY projects..
  • Package Content: 20 PCS B10K Potentiometer + 20 PCS Nuts + 20 PCS Washers + 20 PCS Caps. Assorted in a clear box for quick access and storage, very convenient and easy choice to make your rotary taper potentiometer solid and precise when turning..
Check Stock