Top H bridge Motor Driver

Teco Variable Frequency Drive, 1 HP, 115 Volts 1 Phase Input, 230 Volts 3 Phase Output, L510-101-H1, VFD Inverter for AC motor control

  • H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak).
  • Completely stackable design: 5 address-select pins means up to 32 stackable shields.
  • Characteristic: Arduino interface is fully compatible expansion.
  • Feature: Motors automatically disabled on power-up.
Check Stock

Usongshine Stepper Motor Driver TB6600 4A 9-42V Nema 17 Stepper Motor Driver CNC Controller Single Axes Phase Hybrid Stepper Motor for CNC/42 57 86 Stepper Motor（1 pcs

  • Package included: 1 x Stepper Motor Driver..
  • ✿Stepper Motor Driver✿: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • ✿The largest 32 subdivision of the 6 models are optional.
  • Suitable for 4Wires, 6 wires and 8 wires stepper motor. it can control 2 phase stepper....
  • ✿Protect form✿: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection, under voltage....
  • ✿Suitable for a wide range of stepping motors of Nema 17, 23 and 24 can used in various kinds of machines, such as X-Y-Z tables, labeling machines,....
Check Stock

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

  • DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
  • STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
  • FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
  • PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
  • UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..
Check Stock

Aideepen 5pcs Dual H-Bridge DC Stepper 1.5A 2 Way DC Motor Driver Module Replace Stepper L298N for Smart Car Power

  • Use of imported original chip, built-in low on-resistance MOS switch.
  • Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor.
  • Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped.
  • Minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered.
  • Small size, light weight, low standby current, is the ideal choice for your car model.
Check Stock

AOICRIE 5Pcs L298N Dual H Bridge Stepper Motor Driver Board For Arduino (5pcs)

  • 【Package Included】- 2pcs L298N Motor Driver Controller Board Modules..
  • 【Item Condition】- Drive voltage 5V-35V, high working power to 46V. Large current can reach 3A MAX and continue current is 2A. Power to 25w.(NOTE: To avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.).
  • 【High Quality】- Use L298N as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module..
  • 【High Efficiency】- Dual-channel H-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
  • 【Easy of Use】- No assembly required. This L298N board comes ready to go. Just wire up motors and power, this thing will work wonders..
Check Stock

6 Pack Mini L298N DC Motor Driver, MELIFE MX1508 Mini Dual Channel 1.5A 1.5A 2 Way PWM Speed Controller Dual H-Bridge Replace Stepper

  • Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
  • Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
  • Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
  • Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
  • Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..
Check Stock

ACEIRMC 8pcs L298N Motor Driver Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power MEGA R3 Mega2560

  • When you are driving voltage (above logo for the 12 v input, can actually accept input range is 7 to 12 v) for 7 v to 12 v, can make to onboard power supply 5 v logic, when using the onboard after 5 v power supply, interface of + 5 v The power supply does not input voltage, but can yield 5V voltage for external use..
  • The chip manual proposes to support 35V, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven.
  • Great for for Arduino DIY Smart Car Robot Power MEGA R3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
  • No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
Check Stock

SB New Motorshield for Raspberry Pi 3,2,1 and Zero This Expansion Board can Control up to 4 Motors or 2 Stepper Motor, 2 IR sensors and a Single ultrasonic Sensor.

  • Dual H-Bridge IC L293D. Motor Input Supply Range: 6V - 24V.
  • Single Motor Output Current: 600mA or 1A peak per channel.
  • On board Arrow Indicator for motor direction Indication,.
  • 2 IR sensor connectors with 3.3V level output protection. Control 2 stepper motor.
Check Stock

HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560

  • L298N as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific value.
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.
  • Dual-channel H-bridge driver working mode creates higher working efficiency.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
  • Large capacity filter capacitance, afterflow protection diode, more stable and reliable.
Check Stock

RATTMMOTOR 400W Blushless CNC Air Cooled Spindle Motor ER8 12000RPM + 600W Blushless Spindle Motor Driver LCD Panel without Hall + 55mm Clamp Mount for CNC Router Milling Machine

  • 【Brussless Spindle Motor】Power: 400W.
  • Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
  • 【Brussless Spindle Motor Driver】Maximum driver power: 600W.
  • Maximum driver motor running speed: 12000R/Min.
  • Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
  • The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....
Check Stock

Shredneck TREMPACK 2

  • Includes Shredneck TremBlock & TremTool 2.
  • On some Edge Bridges the TremBlock can be used to hold the bridge in an "UP" position to aid in string changing.
  • TremTool 2 includes 3.0mm Hex for String Locks screws, Locking Nuts, Bridge Height adjustment & 2.0mm Hex for intonations adjustment.
  • TremTool 2 inlcudes mm Hex Includes Standard & Phillips Head Reversible Driver bit for general adjustments.
Check Stock

JUKI MO-6714S Industrial 4-Thread Overlock Sewing Machine

  • ✅Thank you! see below full info. on this machine,--- Get your sewing job done real fast with the Juki DDL-8700H sewing machine that can do up to 5500 stitches per minute. This Juki sewing machine has a large 11-inch arm space that lets you work with even large quilts. The stitch length of this 5500 SPM sewing machine goes up to 5mm which gives you a lot of freedom in doing your job..
  • ✅The sewing machine complies with the "Juki Group Green Procurement Guidelines" on the use of hazardous substances, will be delivered in 3 boxes. 1) machine head, & some accessories* 2) servo motor & v belt 3) table top/legs/drawer/*2 spool-Thread Stand Bobbin Winder Oil Pan/Knee Lifter 1 Bobbins 1 Needles Instruction Manual Screw Driver Machine Oil 2-Euro Hinges & 2 Euro Rubber Mounts Table Rest Pin Safety Belt Guard.
  • ✅1) machine head, & some accessories* 2) servo motor & v belt 3) table top/legs/drawer/*2 spool-Thread Stand Bobbin Winder Oil Pan/Knee Lifter 1 Bobbins 1 Needles Instruction Manual Screw Driver Machine Oil 2-Euro Hinges & 2 Euro Rubber Mounts Table Rest Pin Safety Belt Guard.
Check Stock