Top Hand Tap And Die Set

Astany Snap-on Tools Black Flag Banner 3X5ft

  • Ratcheting T handles wind Dies with a 5° swing arc and have a reversing lever to eliminate hand over hand turning.
  • Twist lock guide system reduces the “walk back” of the die guide and keeps the dies centered while cutting.
  • Ratcheting t wrench works with GEARWRENCH pass thru socket system.
  • Die adapters work with the 3/8inch Drive pass thru ratchet and socket system as well as socket accessories.
  • Auto locking feature allow the tap adapters to be removed safely Blow mold carrying case with tilted tap holders for easy access and storage Set....
Check Stock

ATOPLEE Spiral Point Plug Threading Tap ,5pcs HSS 6542 Titanium Coated Metric Right Hand Thread Taps,M3-M8

  • Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more materials and they will stay sharper for longer..
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of cour....
Check Stock

45 Pc Tap & Die Set Metric Mm Titanium Tungsten Steel Jumbo Thread Renew Tool

  • 86 Piece Tap and Die Set Bearing Steel Sae and Metric Tools, Titanium Coated with Metal Carrying Case.
  • Size:14.8 x 10.7 x 2.2"inch / 37.6 x 27 x 5.6cm. Weight:12lb / 5.4kg. Material upgrading:Alloy Steel 55¡ã- 60¡ã, Sizes Stamped Engraved-etched On the Metal.
  • SAE TAP SIZES and SAE DIE SIZES: 1/8"-27NPT, 4-40, 6-32, 8-32, 10-32, 10-24, 12-24, 1/4"-20, 1/4"-28, 5/16"-18, 5/16-24, 3/8"-16,3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18.
  • METRIC TAP SIZES and METRIC DIE SIZES: M3-0.5, M4-0.7, M5-0.8, M6-1.0, M7-1.0, M8-1.0, M8-1.25, M9-1.25, M10-1.5, M10-1.25, M11-1.5, M11-1.25, M12-1.75, M12-1.5, M14-2, M14-1.5, M16-2, M16-1.5.
  • Ideal for rethreading fasteners and fastener holes for auto and machinery repair. Perfect set for the professional craftsman Tap and die set is designed to thread cutting: tap is used to process internal thread, while the die is for external thread.
  • Easy Storage: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
Check Stock

Eco-Baeerss Tap and Die Set Metri_c and Standard M12 X 1.25mm Tap Die Set Right Hand

  • 【Model】M12 X 1.25mm tap and die set, pitch:1.25mm.
  • 【Material】This threa_d tap is made of H_S_S 6542, which is stronger and more durable than ordinary taps.
  • 【Scope of Application】 This product is suitable for stainless steel, iron, aluminum, copper, ordinary steel, wood and other materials. It can be used for hand-pulled or electric applications..
  • 【Package Included】 1 x tap and 1 x die.
  • 【After Sales Service】 Tap and dies support free returns and exchanges, our friendly customer service always supports our products and responds to all emails within 24 hours.
Check Stock

Hanson 12008 1\ Rd Hex Plain Die Stock for Tap Die Extraction

  • CUT AND RENEW THREADS: The ABN Metric and SAE Standard Tap and Die 60-Piece Rethread Set Rethreading Kit for Cutting External and Internal Threads is a comprehensive set for cutting and renewing external and internal threads to exact standards.
  • SIZES: Metric taps 3x0.5, 4x0.7, 5x0.8, 6x1.0, 7x1.0, 8x1.25, 9x1.25, 10x1.0, 10x1.5, 12x1.75.
  • UNC taps 4-40, 6-32, 8-32, 10-24, 12-24, 1/4, 5/16, 3/8, 7/16, 1/2.
  • UNF taps 10-32, 1/4, 5/16, 3/8, 7/16, 1/2.
  • Metric dies 3x0.5, 4x0.7, 5x0.8, 6x1.0, 7x1.0, 8x1.25, 9x1.25, 10x1.0, 10x1.5, 12x1.75.
  • UNC dies 4-40, 6-32, 8-32, 10-24, 12-24, 1/4, 5/16, 3/8, 7/16, 1/2.
  • UNF dies 10-32, 1/4, 5/16, 3/8, 7/16, 1/2.
  • BUILT TO LAST: Constructed from hardened alloy steel for maximum strength and longevity.
  • Can cut materials such as cast iron, steel, aluminum, copper.
  • EASY STORAGE: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
  • CONTENTS: Package includes coarse and fine threads numbered taps and dies from #4-40 to #12-24 and fractional taps and dies from 1/4"-28 to 1/2"-20, 1/8"-27 NPT tap and die, metric tap and dies from M3x0.5 to M12x1.75, thread gauge, tap handle, die h....
Check Stock

Machine Tap 1/2\-13 UNC Thread Pitch 4 Flutes, High Speed Steel Thread Forming Tap, Uncoated (Bright) Finish, Round Shank with Square End, Plug Chamfer, HSS Machine Screw Plug Tap

  • CUT & RENEW THREADS: The ABN | Metric Tap and Dies Set 110-Piece Metal Threading Kit cuts and renews external and internal threads to exact standards.
  • Ideal for professional machinists and DIY weekend warriors alike to rethread existing auto and machinery fasteners, remove screws/bolts, cut raw material.
  • Tap wrench fits the different sizes of taps, thread taps are used to process internal thread, thread die set is for external thread, plug taps suitable for cleaning and rethreading.
  • FITS YOUR APPLICATION: Metric – Taper taps (2x0.4, 3x0.5, 4x0.7, 5x0.8, 6x7.5, 6x1, 7x0.75, 7x1, 8x0.75, 8x1, 8x1.25, 9x0.75, 9x1, 9x1.25, 10x0.75, 10x1, 10x1.25, 10x1.5, 11x0.75, 11x1, 11x1.25, 11x1.5, 12x0.75, 12x1, 12x1.25, 12x1.5, 12x1.75, 14x1, 14x1.25, 14x1.5, 14x2, 16x1, 16x1.5, 16x2, 18x1.5,).
  • Tap wrenches (M3-M12 x 1/16”-1/2”, M6-M20 x 1/4”-3/4”).
  • Die wrenches (25mm x 1”, 38mm x 1-1/2” OD).
  • BUILT TO LAST: Constructed from chromium-coated high carbon steel for maximum strength and corrosion resistance.
  • Metric tap set has 3-4 flute abrasive cutting edges each so you can easily clean/repair and cut materials such as aluminum, iron, cast iron, alloy steel, carb....
Check Stock

uxcell Tap and Die and Drill Bit Set M14 x 2 Left Hand Thread Milling Tap and Round Die 12mm Cobalt High Speed Steel Twist Drill Bit

  • Compatibility: M14 x 2 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
  • Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
  • Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
  • 12mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
  • Tips: Recommended feed rate: general steel: 6-15m/min.
  • cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Check Stock

uxcell Tap and Die and Drill Bit Set M12 x 1.75 Left Hand Thread Milling Tap and Round Die 10.2mm Cobalt High Speed Steel Twist Drill Bit

  • Compatibility: M12 x 1.75 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
  • Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
  • Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
  • 10.2mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
  • Tips: Recommended feed rate: general steel: 6-15m/min.
  • cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Check Stock

PTSTEL 39 PCS Tap and Die Set Metric & SAE Essential Threading Tool Kit for Cutting External and Internal Threads with Adjustable Handles Accessories and Case

  • High-quality & Durability: PTSTEL metric & SAE tap and die set is made of industrial grade GCR15 bearing steel, which is non-corrosive and durable,....
  • Efficient Cutting: All cutting teeth of the tap and die set are precisely CNC machined and accurately heat treated to a rockwell hardness 60 HRC to....
  • Wide Range of Applications: The cutting thread tool set is processed with internal thread and external thread, and strong torsional force is ideal for....
  • Easy to Storage: Each taps and dies set is equipped with plastic tool box with corresponding scales engraved. You will never get the wrong size when....
  • Most Complete Size: 17pcs metric & SAE tap and die set: SAE: 5/16-18, 3/8-16, 7/16-14, 1/2-13, NPT tap (1/8-27), #4-40, #6-32, #8-32, 1/4-20 METRIC:....
Check Stock

60 PCS Tap and Die Set Metric and Standard Sizes Included Tap Die Kit Metric and SAE for Threading and Rethreading Internal and External Threads

  • SAE & METRIC TAP & DIE SET: These 54 Orion Motor Tech taps and dies cut and clean internal and external threads in common conventional and metric sizes.
  • the set also includes adjustable tap and die wrenches, a T-handle tap wrench, a 1/8" flathead screwdriver, and a thread pitch gauge to cover all your needs.
  • USER-FRIENDLY DESIGN: Our standard and metric tap die set is engineered to tight tolerances to meet professional needs.
  • the tap ends are 5-10mm long to allow easier use with the provided wrenches.
  • WIDE APPLICATION: These threading tools work perfectly to correct or create internal and external threading through wood, copper, aluminum, iron, carbon steel, and more!.
  • CHROMIUM STEEL: The thread repair set is constructed with GCr15 bearing steel heat treated for durable and corrosion-free performance with satisfying longevity.
  • BLOW-MOLDED CASE: The blow-molded case stores and organizes the tools, providing easy portability wherever you need them to thread and rethread internal and external threads.
Check Stock

SAE Tap and Die Set Standard | #4, 6, 8, 10, 12, 1/4, 5/16, 3/8, 7/16, 1/2\ Tap Set and Die Set | Thread Repair Kits for Threading and Rethreading Internal and External Threads

  • SAE TAP & DIE SET: These 34 Orion Motor Tech taps and dies cut and clean internal and external threads in common conventional sizes.
  • the set also includes a long-handled tap wrench, 2 T-handle tap wrenches, an adjustable die wrench, a 1/8" flathead screwdriver, and a thread pitch gauge to cover all your needs.
  • USER-FRIENDLY DESIGN: Our SAE tap and die set is engineered to tight tolerances to meet professional needs.
  • the tap ends are 1/5 to 2/5 in. long to allow easier use with the provided wrenches.
  • WIDE APPLICATION: These tools work perfectly to correct or create internal and external threading through wood, copper, aluminum, iron, carbon steel, and more!.
  • CHROMIUM STEEL: The whole tool set is constructed with GCr15 bearing steel heat treated for durable and corrosion-free performance with satisfying longevity.
  • BLOW-MOLDED CASE: The blow-molded case stores and organizes the tools, providing easy portability wherever you need them.
Check Stock

RIDGID 44923 Model 690-I Hand-Held Power Drive Kit, Pipe Threading Machine and 1/2-Inch to 2-Inch 11-R NPT Pipe Threading Die Heads with Carrying Case for Threading Pipe

  • CUT AND RENEW THREADS: The ABN Metric and SAE Standard Tap and Die 60-Piece Rethread Set Rethreading Kit for Cutting External and Internal Threads is a comprehensive set for cutting and renewing external and internal threads to exact standards.
  • SIZES: Metric taps 3x0.5, 4x0.7, 5x0.8, 6x1.0, 7x1.0, 8x1.25, 9x1.25, 10x1.0, 10x1.5, 12x1.75.
  • UNC taps 4-40, 6-32, 8-32, 10-24, 12-24, 1/4, 5/16, 3/8, 7/16, 1/2.
  • UNF taps 10-32, 1/4, 5/16, 3/8, 7/16, 1/2.
  • Metric dies 3x0.5, 4x0.7, 5x0.8, 6x1.0, 7x1.0, 8x1.25, 9x1.25, 10x1.0, 10x1.5, 12x1.75.
  • UNC dies 4-40, 6-32, 8-32, 10-24, 12-24, 1/4, 5/16, 3/8, 7/16, 1/2.
  • UNF dies 10-32, 1/4, 5/16, 3/8, 7/16, 1/2.
  • BUILT TO LAST: Constructed from hardened alloy steel for maximum strength and longevity.
  • Can cut materials such as cast iron, steel, aluminum, copper.
  • EASY STORAGE: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
  • CONTENTS: Package includes coarse and fine threads numbered taps and dies from #4-40 to #12-24 and fractional taps and dies from 1/4"-28 to 1/2"-20, 1/8"-27 NPT tap and die, metric tap and dies from M3x0.5 to M12x1.75, thread gauge, tap handle, die h....
Check Stock