Top Height Gage

WeldingStop V-WAC Undercut Gauge Biting Edge Welding Guage for Welder Inspection Single Weld Gauge Measure Inspection Tools Porosity Size/amount Inspection Tools Inch Stainless Steel

  • Standard Reading—— The item of Undercut Gauge can be read in Standard. It can measure depth of undercut or pit and the height of misalignment and weld seam(Range: 0-1/4'', Increment: 1/64''). It can check the size in 1/16'',1/8'',1/4'' of porosity and per inch amount.
  • Materials of Stainless Steel—— This undercut gauge is all made by Stainless Steel. No anti-rust methods are required, it is easy to store. The undercut gage will not rust in dry environment.
  • Scales are Laser Engraving—— Every scale on this V-WAC Undercut Gage is takes Laser Engraving. This ensures that wear will not cause the scale to be unclear or hard to read.
  • Synthetic Leather Bag—— We use Synthetic Leather Bag to pack the undercut gauge. When it not use, the undercut gage could by put into the bag for preservation, which can prevent the V-WAC undercut gauge and other tools from friction.
  • Locking Device—— Each Undercut Gauge with a Locking Device, it design for more accurately of reading. When you are measuring the depth of undercut, the locking device can make the pointer fixed and it is convenience to read and write the number. It will not cause wrong reading due to the pointer moving. It can also avoid the difficulty of reading when you use it outdoors, you can fir....
Check Stock

Accusize Industrial Tools 81 Pcs Steel Gauge Block Set, Grade B, P900-S581

  • 81 pc Grade B Steel Gage Block Set with MFG'S certificate.
  • Manufactured under carefully controlled conditions allowing for the highest degrees of accuracy when used at a temperature of 68 degrees F. (20 C)..
  • All gage block sets are assigned serial numbers and accompanied with a certificate of inspection listing the deviation for each block.
  • Each gage block set meets or exceeds federal specification ASME B89.1.9-2002..
  • Hardened to HRC 64 / All gage block sets are made to special standard to resist corrosion and defacement.
Check Stock

Forster Products NATO Chamber Headspace Gage, Rimless, Hardened Steel, Precision Ground, 7.62 NATO Maximum

  • 7.62 NATO CHAMBER HEADSPACE GAGE: The proper use of Headspace Gages is the most reliable way to test rifle chamber length. These rimless chambers require a slightly longer maximum headspace than commercial 308 Win calibers. The 7.62 NATO Headspace Gages do not conform to SAAMI tolerances..
  • MAXIMUM LENGTH: The Forster NATO Maximum rifle chamber gage checks to see that the rifle does not have excessive headspace, which could lead to dangerous pressure problems. The NATO Maximum Headspace Gage measures 1.6455″.
  • PRECISION MACHINED: Manufactured from top-quality, hardened steel and precision ground to ANSI and SAAMI tolerances. Headspace tolerance ground to a very exacting ±.00015..
  • QUALITY ASSURED: Each Headspace Gage thoroughly inspected with NIST-certified measurement tools to ensure the highest quality product..
  • MEASURING MEANINGFUL HEADSPACE: Properly speaking, and for safety purposes, one measures “headspace” as the difference between the length of a standard cartridge, as represented by a gage, and the gun’s actual chamber length , when the head of the cartridge is flush against the bolt face..
Check Stock

Shorpioen 255-Pack 6-18 x 1 1/2 Phillips Bugle Head Fine Thread Drywall Screw Black Phosphate BC-0624YPG

  • Fine thread Drywall--Sharp point: For attaching drywall to metal studs from 25 gage through 20 gage thick.  Longer sizes are ideal for multiple layers or insulation. Fine thread Drywall--Drill point: Will drive easily through drywall, drill a hole in a steel stud up to 14 gage thick, and form its own mating thread.  Can also be used for attaching plywood or insulation board to 14 gage metal.
  • Screws shall be quenched in liquid and then tempered by reheating to 650°F minimum.
Check Stock

Fowler 54-646-401-0 Electronic Dial Bore Gage Set with 1.4–6\/35-150mm Range

  • Accurate Measurements: The bore gage features an electronic indicator with resolution of 0.00005"/.001mm and measuring depth of 9 inches.
  • Durable Construction: This electronic indicator provides both inch and metric readings.
  • two-point contact system is used to detect geometry problems such as ovality and taper.
  • carbide-tipped contact points provide extended wear and improved abrasion resistance.
  • The easily adjustable bore gage is self-centering and includes a 2-inch contact extension holder.
  • Minimum Hold Feature: This electric gage locks and holds the bore size as the gage is rocked within the part to be measured.
  • Set Includes: A storage case, 2 batteries, 15 measuring anvils, 4 spacers and an instruction manual.
Check Stock

Gun, Hand Gun - Colt 45 Acp: Eight Shots Handgun, Pistol & Revolver Firing, Sound FX

  • Dillon Case Gage 45 ACP, Case Gage, reloading equipment, reloading parts, reloading accessories, 45 ACP case gage.
Check Stock

.626-.750\ Minus Tolerance Pin Gage Set

  • Gage increments are in .001" steps Minus tolerance: +0/-.0002". Fully hardened to 60-62 RC. Each gage is inspected and has a 10 Micron finish or better. Complete with plastic, element-proof fitted case..
Check Stock

Fowler 53-646-000-1, Inch Bore Gage Setting Master Kit

  • Accurate Measurements: Used for accurately setting any bore gage up to 6" in diameter to an accuracy of 0.0001".
  • comes with a base anvil of 2.750" x 0.80" and 2 adjustable anvils of 2.375" x 0.375".
  • Bore Gage Capacity: This bore gage master has an internal capacity of 6.
Check Stock

MC-1-M .061-.250\ by .001\ Minus Tolerance Pin Gage Set - 190 Gages

  • Gage increments are in .001" steps Minus tolerance: +0/-.0002". Fully hardened to 60-62 RC. Each gage is inspected and has a 10 Micron finish or better. Complete with plastic, element-proof fitted case..
Check Stock

Forster Products Sammi Dimensioned Headspace Gage, Rimless, Hardened Steel, Precision Ground, 350 Legend, NO-GO

  • 350 LEGEND: Use to check headspace of 350 Legend..
  • RIMLESS CARTRIDGE HEADSPACE: The proper use of Headspace Gages is the most reliable way to test rifle chamber length. Headspace in a rimless cartridge is the distance between the bolt face and a datum line, determined by SAAMI, where the front of the cartridge rests on its shoulder when the bolt is closed..
  • NO-GO: Corresponds to the maximum headspace we recommend for gunsmiths’ chambering new bolt-action rifles. This is not a SAAMI-maximum measurement. If a rifle closes on a NO-GO gage, it may still be within SAAMI specifications, or it may have excessive headspace. To determine if there is excessive headspace, the chamber should then be checked with a FIELD gage. The NO-GO gage is a valuable tool for gunsmiths’ reaming new chambers, in order to ensure tight and accurate headspace.
  • PRECISION MACHINED: Manufactured from top-quality, hardened steel and precision ground to ANSI and SAAMI tolerances. Headspace tolerance ground to a very exacting ±.00015. Each Headspace Gage thoroughly inspected with NIST-certified measurement tools to ensure the highest quality product..
  • MEASURING MEANINGFUL HEADSPACE: Properly speaking, and for safety purposes, one measures “headspace” as the difference betwee....
Check Stock

Forster Products 223 Remington NOGO Headspace Gage

  • NO-GO: Corresponds to the maximum headspace we recommend for gunsmiths’ chambering new bolt-action rifles. This is not a SAAMI-maximum measurement. If a rifle closes on a NO-GO gage, it may still be within SAAMI specifications, or it may have excessive headspace. To determine if there is excessive headspace, the chamber should then be checked with a FIELD gage. The NO-GO gage is a valuable tool for gunsmiths’ reaming new chambers, in order to ensure tight and accurate headspace..
Check Stock

Telescoping Gauge Gage Set Tools 6 Pcs 5/16'' - 6'' Range Micrometer Precision T-Bore Hole Gauge

  • Multispecification measurement range, 6 piece Telescoping Gage Set, can detect hole (or slot) ID 5/16 "-6"（8mm-150mm）.
  • Telescoping Gage Set INCLUBE:A - 8 To 12.7 mm 5/16 "To 1/2".
  • The Telescoping Gage Set is a stainless steel material that prevents rust and extends the life of the Telescoping Gage Set, a satin chrome plated surface that includes the case, contact points of hardened tool steel, Telescoping spring, with a knurled locking knob and a knurled holding area..
  • Easy-to-adjust to allow the most pinhole gauge on the retractable gauge to enter, groove and groove up to 6 inches deep..
Check Stock