Top Hose Barbs With Push lock

Keg Disconnect Ball Lock MFL Ball Lock Fittings Keg Connectors – Keg Coupler Stainless Ball Lock Keg Fittings 12-Piece

DISPENSE YOUR FAVORITE BEVERAGES: Use the G. Francis Ball Lock Keg Fitting Ball Locks 12-Piece Ball Lock Quick Disconnect Set with Liquid & Gas Disconnects, Swivel Nuts, & Hose Clamps to ferment and dispense craft cocktails, soda, and other beverages from your existing keg.
USE YOUR KEG: Each of the ball lock keg connectors (fittings) have an approximate 2.2-inch height and 1.3-inch outside diameter (5.6cm x 3.3cm) and is compatible with ball lock Cornelius (Corny) kegs and keg couple adapters for homebrewing.
Hose clamps have 0.2-inch to 0.5-inch (6-12mm) diameter while the barbed swivel nuts have 5/16-inch outside diameter (OD) fitted for 1/4-inch or 3/16-inch inside diameter (ID) hoses on your 3, 5, or 10 gallon keg.
BUILT TO LAST: Keg ball lock quick disconnects and hose clamp wings constructed from ABS plastic that resists rust and corrosion.
Swivel nuts and clamps constructed from food-grade stainless steel for maximum strength and longevity.
INSTALL EASILY: Tighten the swivel nut connecting the flare fitting before use.
Ensure correct fittings are installed on input and output posts – Light gray disconnect for gas inlet and black disconnect for fluid outlet.

【Package Quantity】: Package includes 60 pieces of elbow hose connectors, which let you connect your irrigation systems as you wish.
【Barbed Design】: The barbed ends grab tubing, which makes the tube connection more firm, and not easy to fall off, ensure a secure leak-proof connection..
【Material】: The drip line elbows are made of high quality engineering plastics, solid and durable, ensure years of using..
【Easy to Install】: It is easy to install without any glue, tools or clamps. Simply push the tubing firmly over the barbs for a very tight fit that won't leak..
【Wide Application】: These elbow fittings are suitable for garden, lawn, greenhouse, patio and other watering drip irrigation system..

⌘【Heavy Duty】: These 5/8 garden hose repair fittings can fix and secure the ends of damaged hoses for continued use in garden hose assemblies..
⌘【Leak Resistant Duty】: This garden hose mender has raised ridges (or barbs) on one end of the fitting that hold it firmly in place when it is inserted into the damaged hose, creating a leak-resistant seal..
⌘【Material】: Water hose repair kit connectors are made of brass, and the clamps are made of stainless steel..
⌘【Easy to Use】: Easy to connect and disconnect, male hose end repair can be uses to repair and connect the garden hose ends. Fit for ⅝" or ¾" hose fittings..
⌘【Package Include】: 4 sets male and female hose end repair connector with clamp, extra 8 pack garden hose washers..

Equipped with a pulsating gun assembly with a pre-set regulator for accuracy.
Hinders water line backflow to lessen water pump damage.
Large rubber tip for radiator necks and direct flushing of the engine block.
Small rubber tip on the whip hose for direct access to the heater core tube stubs.
5?8 in and 3?4 in heater hose barbs for flushing heater cores or engine blocks.

【Solid Brass】The hose barb fittings are made of solid brass, which is strong and not easily corroded, suitable for long time use..
【Package Include】3PCS 5/8"x5/8"x5/8" Brass 90°Included Angle Y Hose Barb Fittings..
【Heavy & Thick】Heavy Y shaped brass barbs and thickened wall, higher strength and very rugged..
【Solid Connection】The Y shaped hose barb fittings can be solid connected to the hose (Fit hose which ID of 16mm)..
【Note】Keep the water pipe incision flat. It is better to use with clamps (Not include). Tighten clamps as tightly as possible to prevent leakage..

Removes sediment.Perfect for large batches and dry hopped beers..
No Taste-spoiling aeration or chemicals. Save time and beer..
Include 6 hose barbs 1/2"(12mm) hose barb, 3/8"(9mm)hose barb, 1/4"(6mm)hose barb available..
Screen: 180 micron / 80 mesh Max Operating Temperature: 65C/150F Max Operating Pressure: up to 150 psi.

800 GPH, 12V, Fuse size: 4A, Outlet type: 3/4" & 1" barbs, Check valve: yes, Wire length: 29 1/2".
The easiest, most reliable automatic bilge pump ever designed.
The only automatic bilge pump that eliminates air-locks, Patented X-Air Impeller ejects trapped air in the pump and pipework.
Flexible Outlets: 90° rotatable elbow outlet allows users to install the pump anywhere in a full 360° orientation.
Single-Hand Pump Cartridge Release: Convenient when trying to access a pump located in a hard-to-reach area of the boat’s hull.
Universal Backwards Compatible Design: 7-pump mounting hole pattern for replacing any top bilge pump in its category.
SteadySwitch: Buoyancy control reduces cycling, draining the bilge not the battery.
No Pipe Or Hose Removal Required: Reduces the time that it takes to replace the cartridge.
Improved Motor Cooling/Heat Dissipation: Prevents overheating that may cause failures, such as blown fuse, leaking, etc..
Includes straight outlet and check valve.