Top Hose Fitting With Male Pipe Threads
Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP
- 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check StockClass A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP
- 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Check StockRV Winterize Blowout Adapter, Blowout Adapter for Winterizing with 1/4 Inch Quick Connecting Plug and 3/4 Inch Garden Water Hose Threading, RV Winterizing Kit with Ball Valve for RV Boat Camper
- 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check StockSUNGATOR 3 Pack Barbed Brass Hose Fittings 1/2 Barb to 1/2 NPT Male Threaded End Fittings Hose Connector Adapter with Sealing Tape and Hose Clamps
- 【SIZE AND PACKAGING】: 1/2"barb X 1/2"NPT male pipe, package includes 3 hose barb fittings, 1 sealing tape, 3 hose clamps.
- 【DURABLE】: Made of High quality solid brass, not a cast product and has a thick wall, this hose barb fitting is firm and durable, and provides high resistance to abrasion and corrosion, longer service life than iron and iron galvanized pipe fittings.
- 【SUPERIOR THREADS】: Deeper and smoother threads with barbed edges provide effective and tight connection, not easy to slip.
- 【OPERATING TEMPERATURES】: Solid brass can withstand up to 100 °C (212 °F).
- 【FUNCTION】: Barb head for connecting hoses, NPT male end used to connect NPT pipes, the hose barb fittings can apply to gas, oil and fuel as well as air tools.
Check StockSUNGATOR Brass Barbed Hose Fittings 1 Barb to 1 NPT Male Threaded End Hose Barb Pipe Fittings Hose Adapter Connector with Sealing Tape and Hose Clamps 2 Pack
- 【SIZE AND PACKAGING】: 1"barb X 1"NPT male pipe, package includes 2 hose barb fittings, 1 sealing tape, 2 hose clamps.
- 【DURABLE】: Made of High quality solid brass, not a cast product and has a thick wall, this hose barb fitting is firm and durable, and provides high resistance to abrasion and corrosion, longer service life than iron and iron galvanized pipe fittings.
- 【SUPERIOR THREADS】: Deeper and smoother threads with barbed edges provide effective and tight connection, not easy to slip.
- 【OPERATING TEMPERATURES】: Solid brass can withstand up to 100 °C (212 °F).
- 【FUNCTION】: Barb head for connecting hoses, NPT male end used to connect NPT pipes, the hose barb fittings can apply to gas, oil and fuel.
Check StockJoywayus Hex Nipple 1/2' Male x 1/2' Male Threaded Stainless Steel 304 Threaded Nipple Pipe Fittings for Brew Kit Home Piping (Pack of 5)
- 【Size】1/2" Male x 1/2" Male Thread. Tapered thread. Pipe fittings are components used for connecting, terminating, controlling flow, and changing the direction of pipe..
- 【High Quality Material &Threads】Made of quality stainless steel 304, durable and sturdy corrosion resistance, ductility at high temperatures, and low magnetic permeability. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip..
- 【Hex Nipple】The hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench..
- 【Operating temperature range】Temperature rating: -65 to 250 degrees F.
- 【Widely Applications】Male threads for connecting to female threaded pipes, this premium pipe fitting can be used to connect various pipes, such as air pipe, fuel pipe, water pipe as well as air tools.
- it can also be used with grease, fuels, LP and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
Check StockSpringSpray 1-1/2\ NPT Male x 1-1/2\ NST (NH) Male Brass Hexagonal Nipple Fitting Fire Equipment Hex Nipple Doule Male Fire Hose Adapter
- ⚒【PREMIUM MATERIAL】- Made of brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability. The Fire Equipment Hexagonal Nipple Fitting offer long-term service.
- ⚒【CONNECTION SIZE】- Hex nipple fitting 1-1/2" NH/NST to 1-1/2" NPT double male fire hose adapter. Male 1-1/2 inch NH / NST will only connect to a female 1 1/2 inch NH / NST.
- Male 1-1/2 inch NPT will only connect to a female 1-1/2 inch NPT/NPSH.
- ⚒【UNIQUE DESIGN】- With hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench. Hex tube fitting as a short length of pipe with threaded ends for connecting threaded pipes.
- ⚒【WIDE APPLICATION】- Male to male adapters are used to bridge two female hose, pipe or valve fittings. Suitable for use in general firefighting applications. Brass fire hydrant adapter fittings are used for connecting fire hose, PVC pipe, and other low-pressure pipes in the fire brigade, industry, refinery, building industry, agriculture, shipping, military, and civil protection.
- ⚒【100% SATISFACTION SERVICE】-We have a professional product development team. If you have any questions about compatibility or any dissatisfaction, please feel free to contact us and we will help you ....
Check StockMaster Airbrush Brand 100 Pipette Eyedroppers for Liquid Transfer and Airbrush Paint
- Master Airbrush Brand Airbrush Fitting Conversion Adapter for Badger Airbrushes.
- Converts a Badger airbrushes male M5 0.5 mm thread size to standard 1/8" BSP male thread size for easy connection to 1/8" BSP air hoses.
- Adapter has 1/8" BSP male threads on the outside and Badger size female threads on the inside.
- The adapters 1/8" BSP hose thread size is the most common hose fitting size used for many popular airbrush brands like Master and Iwata.
Check StockClass A Customs | 30 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-3000-BPK-PUMP
- 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - BPA FREE - NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Gray Water Storage ||WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” (rotate tank to change height or width) Average thickness 7/32” +/- (+/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Balloon Style Threaded Female NPT Standard - fitting will be closed, to use remove inner membrane with razor knife (TWO) .5" Threaded Female NPT Standard - open fitting, unsealed.
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT hook garden hose directly to tank doing so will cause tank to explode resulting in damage..
- BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check StockThread Reducer Bushing 2" Male x 1-1/2" Female Adapter Pipe Fitting with Stainless Steel 304 NPT
- Maximum working pressure of 150 psi at 70 degrees F.
- NPT thread for creating tighter seals than straight threads.
- Shape:Reducer Bushing(Male x Female),Connection:NPT-NPT,Measurement:2"x1-1/2".
- This adapter fitting connects pipes or fittings with different end types, diameters, or materials.
- It has male NPT threads on one end and female NPT threads on the other for connecting to a female and a male threaded pipe or fitting..
Check StockHose Fitting SUNGATOR Brass Hose Barb Fitting Adapter 1/4 Barb x 1/4 NPT Male Pipe 4-Pack
- 【PREMIUM MATERIAL】: SUNGATOR selects high quality solid brass, firm and durable, brass is corrosion resistant and can be used in wet environments, 1/4”barb X 1/4”NPT male pipe, 4 pack.
- 【DURABLE】: The barb fitting is not a cast product and has a longer service life.
- 【SUPERIOR THREADS】: Barbed edges provide excellent connection, deeper and smoother threads design makes work easier and more effective.
- 【FUNCTION】: A barb (or hose barb), which connects flexible hose or tubing to pipes, one side is used to connect hoses while the other side is used to connect to NPT pipes, especially for small rubber hoses and plastic hoses as well as air tools.
- 【OPERATING TEMPERATURES】: Solid brass can withstand up to 100 °C (212 °F).
Check StockAC PERFORMANCE Stainless Steel -3 AN 3/8x24 Male Flare Union Splits Tee Block With Lug/Mount Tab/Locator, -3 AN to 2x AN3 Male Flare Coupling Union All Sides Hose Fitting
- Male -3 AN to 2 x -3AN Flare (JIC -3, 3/8×24 thread) with Tab T Pipe Tee Block Hose Fitting Adapter.
- Works with -3AN TEFLON PTFE Brake and Clutch Hose / Line, Design For Drift / Hydraulic Hand Brake application.
- AN Male Flare Tee Tube Fitting with Locating Lug Mount Hole.
- Male -3AN flare all sides Tee cross 3 ways pipe with lug tab locator SL fitting connector.
Check Stock