Top I2c Cable

5 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V(Blue Display Color)

  • What will you get: there are 5 pieces OLED display module with blue display color, self-illuminated and no need backlight.
  • Power-saving display: the I2c oled display performs better than the traditional LCD display and with lower consumption sicne the IIC (I2C communications) simplifies connections.
  • Please note that these I2C OLED display module comes without pin headers.
  • More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
  • Good compatibility: this i2c oled display module is compatitable with Raspberry Pi 4B/3B+/3B/2B/Zero, compatitable with Arduino, also compatitable for ESP8266, ESP32, STM32, etc..
  • Product manual: as shown in the instructions.
Check Stock

ACEIRMC 8pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino

  • The adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use..
  • TCA9548 TCA9548A 1-to-8 I2C 8 -way multi-channel Expansion Board IIC Module Development Board.
Check Stock

Clock Splitter, Good Performance High Practical Electronic Component for Industry for Home

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

JM Set of 3 pcs Transparent 3D Floating Frame Display Holder/Box/Frames for Challenge Coins, AA Medallions, Antique, Jewelry,Gift, White, 2.75 x 2.75 x 0.75 Inches

  • What will you get: there are 5 pieces OLED display module with classic display color, self-illuminated and no need backlight.
  • Power-saving display: the I2C oled display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications) simplifies connections.
  • Please note that these I2C OLED display module comes without pin headers.
  • More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
  • Good compatibility: this i2c oled display module is compatible with Raspberry Pi 4B/3B+/3B/2B/Zero, compatible with Arduino, also compatible with ESP8266, ESP32, STM32, etc..
  • Product manual: as shown in the instructions.
Check Stock

SunFounder 2004 20x4 LCD Module IIC I2C Interface Adapter Blue Backlight Compatible with MEGA2560 Arduino R3 Raspberry (2 Pack)

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each. (2 Pack).
  • Compatible with Arduino R3/Mega2560 board..
Check Stock

SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield Compatible with Arduino R3 Mega2560

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each..
  • I2C Address: 0x27 or 0x3F.Compatible with Arduino R3/2560 board. http://wiki.sunfounder.cc/index.php?title=I2C_LCD2004.
  • Professonal Support: SunFounder customer service team are always willing to solve any question from our customers .Any problem, please contact us on Amazon..
Check Stock

Pisugar 3 Plus Portable 5000 mAh UPS Lithium Battery Power Module Platform for Every Raspberry Pi 3B/3B+/4B Model Accessories handhold(Not Include Raspberry Pi)

  • PiSugar 3 plus adds a software watchdog function. When the function is turned on, the dog needs to be kicked regularly, which can effectively prevent the Raspberry Pi from crashing and improve the reliability of the system..
  • PiSugar 3 plus provides hardware battery protection like never before, limiting battery voltage to nearly 80%. When charging protection is turned on, the battery cycles life can be improved.Set up quadruple overvoltage protection function, overcurrent protection function and undervoltage protection function to ensure the safety of the Raspberry Pi, PiSugar as well as the lithium battery..
  • PiSugar 3 plus continues to use the pogo pin design to connect with Raspberry Pi from the back. In this way, it does not occupy the GPIO, and is compatible with other GPIO devices..
  • PiSugar 3 plus has full UPS functions and can set up multiple awakening methods to meet various unique project needs..
  • PiSugar 3 plus communicates with the Raspberry Pi through the I2C interface and is compatible with most I2C devices. In addition, the I2C communication address can be customized to avoid I2C address conflicts..
Check Stock

AITRIP 10PCS PCF8574 PCF8574T IO Expansion Board I/O Expander I2C Evaluation Develop Module

  • The PCF8574 IO Expansion Board provides general-purpose remote I O expansion via the two-wire bidirectional I2C-bus (serial clock (SCL), serial data (SDA)..
  • The main resources: PCF8574, I2C interface, the 8-bit parallel.
  • Typical applications: for I / O resource constraints the MCU I / O expansion.
  • PCF8574T expansion board applicable to a variety of platforms including AVR / ARM.
  • PCF8574T PCF8574 IO expansion board support I2C bus cascade (by pin header row seat docking methods can be used simultaneously multiple I2C modules).
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

Treedix TCA9548A I2C Multiplexer Breakout Board 8 Channel Expansion Board with pi Header for Arduino

  • The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
  • TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
  • The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
  • In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
  • The chip is compatible with 3V and 5V and can be used with any logic level.
Check Stock

Digital Microphone Amplifier, Reverberation Board Low Noise for Audio Equipments

  • For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples..
  • Cond over I2C,The chip can be configured as 4 single-ended input channels, or two differential channels..
  • As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range..
  • We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 12 bit converter..
  • The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed , you can have up to 4 ADS1015's connected on a single 2-wire I2C bus for 16 single ended inputs..
Check Stock

HiLetgo MCP4725 12 Bit I2C IIC DAC Development Board Breakout Board Internal EEPROM Store Settings for Arduino

  • The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC)..
  • A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller..
  • On board are SCL, SDA, VCC, and another GND for your basic I2C pinout..
  • If you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.store settings.
  • Digital to analog converters are greInternal EEPROM to store settingsat for sound generation, musical instruments, and many other creative projects!.
Check Stock