Top I2c Support

Treedix JST Female Connector Breakout Board 4 Channel Mux MultiPort Pitch 1.0mm for JST Male Plug

  • Upgraded from the original basis, MultiPort has multiple connection ports.
  • You can use it as a hub to add I2C devices to the bus as you need, including mounting holes, so the board can be fixed to any system.
  • There are 4pcs 1.00mm 4-pin female connectors and Mounting Points.
  • All boards that support 1mm pitch 4-pin JST connector, which can reduce the required PCB space..
  • To make using this multiplexer easier, all communication is done via I2C using our convenient Qwiic system..
Check Stock

SparkFun Digital Temperature Sensor - TMP102 (Qwiic)-Compatible with Arduino and other Single-board computers Easy-to-Use I2C sensor Plug-and-Play breakout board Runs from 1.4-3.6V input Use with 3.3V

  • Uses the I2C interface. I2C Address: 0x48 by default (Three additional addresses available, as well). 12-bit, 0.0625°C resolution. Typical temperature accuracy of ±0.5°C.
  • 3.3V sensor. Supports up to four TMP102 sensors on the I2C bus at a time. 2x Qwiic Connectors.
  • The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V..
  • I2C communication uses an open drain signaling, so there is no need to use level shifting..
  • The alert pin is an over temperature alert, which has an open-drain and is pulled up through a 10kΩ resistor. The alert can also be read over I2C.
Check Stock

ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire

  • ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
  • FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
  • This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Check Stock

DORHEA 2Pcs BME280 5V Temperature Humidity Atmospheric Barometric Pressure Sensor Module GY-BME280-5V IIC I2C Breakout Board

  • The BME280 sensor is a precision sensor, is soldered onto PCB, not only the pressure and the temperature, this sensor can measure humidity..
  • BME280 5V uses both I2C and SPI (supports 3-, 4-wire SPI) interface. Interface: I2C (up to 3.4MHz).
  • Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI. for simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI..
  • The BME280 stmospheric pressure sensor is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings..
  • The BME280 sensor is precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy..
Check Stock

AITRIP D1 Mini WiFi Dev Board,Mini NodeMcu Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini (Pack of 6)

  • （pack of 6 ）This D1 mini module is a mini WIFI board based on ESP-8266EX..
  • Our D1 mini development board is 100% compatible with Arduino WeMos and can be programmed in Compatible with Arduino IDE..
  • Support OTA on line.Compatible withArduino compatibility. Using Compatible with Arduino IDE for programming..
  • This WLAN board contains 11 digital input / output pins, all pins have interrupt / pwm / I2C / 1-wire and a micro-USB connection..
  • 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
  • 1 analog input(3.2V max input). Micro USB connection.
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

2 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module Blue I2C OLED Screen Driver DC 3.3V - 5V

  • What you will get: you will get 2 OLED display modules with classic display colors, self illumination with no need of backlight.
  • Power-saving display: the I2C OLED display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications)....
  • More details: this I2C LCD display is compatible with Arduino, ESP8266, ESP32, STM32, etc., 3.35V power.
  • Operating temperature: -40 - 85 degree....
  • Good compatibility: this I2C OLED display module is compatible with Raspberry Pi 4B/ 3B+/ 3B/ 2B/ Zero, compatible with Arduino, also compatible with....
  • Product manual: as shown in the instructions.
Check Stock

DS3231 AT24C32 IIC RTC Module Clock Timer Memory Module Beats Replace DS1307 I2C RTC Board (Batteries not Included) + 20 PCS Male to Female Jumper Wire Cable

  • DS1307 I2C real-time clock chip (RTC) 24C32 32K I2C EEPROM memory..
  • The DS1307 is accessed via the I2C protocol..
  • Two wire I2C interface. Hour: minutes: seconds AM/PM. Day month, date - year，Accurate calendar up to year 2100..
  • 1Hz output pin.56 Bytes of non-volatile memory available to user..
  • Size: 2.8cm x 2.7cm. / 1.14inch x 1.02inch..
Check Stock

Aoicrie 16x2 2004 LCD Display Module with IIC/I2C/TWI Serial Interface Adapter, IIC I2C TWI 1602 Serial LCD Module Display, for Mega 2560

  • IIC I2C TWI 1602 Serial LCD Module Display for R3 Mega 2560 16x2..
  • Easy to use. Less I/O ports are occupied, only four - VCC, GND, SDA (serial data line), SCL (serial clock line)..
  • Support IIC protocol. The I2C LCD1602 library is provided, so you can call it directly..
  • With a potentiometer used to adjust backlight and contrast.Power supply: +5V, Address of the module: ox27..
  • Widely Applications: LCD display module based on the popular HD44780 controller, works great with for Mega2560 board and other micro-controllers..
Check Stock

5 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V(Blue Display Color)

  • What will you get: there are 5 pieces OLED display module with blue display color, self-illuminated and no need backlight.
  • Power-saving display: the I2c oled display performs better than the traditional LCD display and with lower consumption sicne the IIC (I2C communications) simplifies connections.
  • Please note that these I2C OLED display module comes without pin headers.
  • More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
  • Good compatibility: this i2c oled display module is compatitable with Raspberry Pi 4B/3B+/3B/2B/Zero, compatitable with Arduino, also compatitable for ESP8266, ESP32, STM32, etc..
  • Product manual: as shown in the instructions.
Check Stock

ACEIRMC 8pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino

  • The adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use..
  • TCA9548 TCA9548A 1-to-8 I2C 8 -way multi-channel Expansion Board IIC Module Development Board.
Check Stock

JM Set of 3 pcs Transparent 3D Floating Frame Display Holder/Box/Frames for Challenge Coins, AA Medallions, Antique, Jewelry,Gift, White, 2.75 x 2.75 x 0.75 Inches

  • What will you get: there are 5 pieces OLED display module with classic display color, self-illuminated and no need backlight.
  • Power-saving display: the I2C oled display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications) simplifies connections.
  • Please note that these I2C OLED display module comes without pin headers.
  • More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
  • Good compatibility: this i2c oled display module is compatible with Raspberry Pi 4B/3B+/3B/2B/Zero, compatible with Arduino, also compatible with ESP8266, ESP32, STM32, etc..
  • Product manual: as shown in the instructions.
Check Stock