Top Isolated Current Transducer

ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino

  • It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
  • Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
  • RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
  • With optical coupling isolation, triggering more reliable, more stable..
  • EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..
Check Stock

Hantek 6254BE Digital oscilloscope 250MHz Bandwidth Automotive Oscilloscopes Car-Detector 4 Channels 1Gsa/s USB PC Osciloscopio

  • ⚡【AC/DC amp clamp meter】 Hantek AC/DC Current amp Clamp probe with bnc for oscilloscope, 20kHz Bandwidth, 1mV/10mA, 65A.
  • ⚡【Multifunction】It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms..
  • ⚡【BNC Probe】if connect to an oscilloscope by BNC type connector, you're able to observe the current waveforms.
  • ⚡【Application】1.Power circuit measurement and malfunction analysis.
  • 2.Motor drive of frequency converter (or other electronics) measurement.
  • 3.Power electronics equipments measurement..
  • ⚡【What you will get】1*AC/DC Current clamp CC-65,1*English Manual..
Check Stock

Donner DP-1 Guitar Power Supply with DP-Z 9V Guitar Pedal Power Supply 11 Isolated DC Output with USB Port for 9V/12V/18V Effect Pedal DC 18v 2000m Input

  • 10 ISOLATED OUTPUTS:Donner DP-1 9V Guitar Pedal Power Supply has 10 outputs ,which includes 7 ways 9V 100mA, 1 way 9V 500mA, 1 way 12V 100mA, 1 way 18V 100mA..
  • NOISE REDUCTION CIRCUIT DESIGN：Donner Guitar Pedal Power Supply Quality is made of aluminum alloy material, which makes it light, and portable. It has a noise reduction function, low noise gives you a better experience, and direct current increases the stability of the power supply during use..
  • 【Super Power Adapter】Donner DP-Z 9V Guitar Pedal Power Supply equips with superpower adapter: DC 18v 2000mA ，this powerful input ensures that every output is in the best possible state..
  • 【10 Isolated Outputs + 1 USB charge port 】 Donner DP-Z 9V Guitar Pedal Power Supply has 10 outputs ,which includes 4 x 9V 100mA, 3 x 9V 300mA, 1 x 9V 500mA, 1 x 9V/12V 500mA, 1 x 18V 300mA with 1 x DC 18V input, 1 x USB charge port. 10 Isolated Output ,5v 1000 mA USB charge port Meet the power demand of Mobile devices ..
  • 【Noise Reduction Circuit Design】Donner Guitar Pedal Power Supply Quality is made of aluminum alloy material, which makes it light, and portable. It has a noise reduction function, low noise gives you a better experience, and direct current increases the stability of the power supply during u....
Check Stock

bayite DC 5-120V 400A Mini Digital Current Voltage Amp Meter Gauge with Hall Effect Sensor Transformer

  • Electrically isolated from high voltage power source which eliminates risk to delicate monitoring equipment and also minimizes safety concerns.
  • Diameter of the hole through sensor is 3/4 inch(19 mm).
  • Loop through sensor multiple times to strengthen signal. For example, if your current signal is only 0.2 Amps, you could loop the wire through the....
Check Stock

CR Magnetics CR9380-PNP-M PNP Transistor Output Split Core Current Switch with Mounting Case, Normally Open, 30 VDC

  • Current switch for monitoring current flow.
  • Current carrying wire is routed through an aperture.
  • Electrically isolated normally open (NO) switch.
Check Stock

bayite DC 5-120V 100A Mini Digital Current Voltage Amp Meter Ammeter Gauge with Hall Effect Sensor Transformer

  • Electrically isolated from high voltage power source which eliminates risk to delicate monitoring equipment and also minimizes safety concerns.
  • Diameter of the hole through sensor is 3/4 inch(19 mm).
  • Loop through sensor multiple times to strengthen signal. For example, if your current signal is only 0.2 Amps, you could loop the wire through the....
Check Stock

B&K Precision 9129B Triple Output Power Supply

  • Three independent and electrically isolated outputs.
  • Displays voltage and current settings for all three channels simultaneously.
  • Series and parallel modes combine channels to increase the output voltage or current.
  • Tracking mode allows users to set up channels to maintain a programmed ratio.
  • Fully programmable channels with output On/Off control.
Check Stock

Sovvid Guitar Pedal Power Supply - Pedal Board Power Supply 10 Isolated DC Output for 9V/12V/18V Effect Pedal Guitar Power Supply Pedal Power Adapter with Short Circuit and Ovrcurrent Protection

  • 【10 Isolated Output, Stable Current】: Sovvid pedal power supply is very safe and secure. 10 isolated output has separate short circuit protection. Short circuit in one channel won't affect other channels' function. This pedal board power supply can produce perfect tone and supply stable current. It includes 9V 100mA port x 6, 9V 500mA port x 2, 12V 100mA port x 1, 18V 100mA port x 1..
  • 【Noise Free, Heat Dissipation】: Sovvid pedalboard power supply has built-in powerful noise filter and good shielding effect. Which makes the radiation and current noise in a very limited range. And the premium quality chips has perfect heat-dissipating performance than other pedal adapter. There is enough space inside the equipment for rapid cooling. You will get a clear and firm sound when playing..
  • 【Short Circuit and Over Current Protection】: Each port has separate short circuit and over current protection. When one port is short-circuited or get current overload due to misuse or accident, this guitar power supply will protect your pedal board main body and protect it from damage..
  • 【LED Indicator, Robust Steel Casing】: The Blue LED lights will indicate the short short-circuit or overload problem. When Turn on LED indicator switch, short-circuited channel ....
Check Stock

Signal Isolator, Signal Conditioner Current 4-20mA for Transmitter for Isolated Power Distribution Power Supply

  • High quality signal isolator, stable performance, durable and reliable..
  • Strong input signal processing ability, able to accept and process thermocouple, thermal resistance, frequency and other signals.
  • Have the advantage of high precision,high linearity and strong anti-interference..
  • The input, output and power are isolated from each other by adopting highly efficient magnetoelectric isolation technology interiorly..
  • This signal isolator provides isolated power distribution power supply for transmitter,meanwhile it isolates and converts the current signal to control room..
Check Stock

Heitune Voltage Meter, D85-3050 Digital DC Voltmeter Ammeter Volt Amp Meter DC0-199.9V DC0-10.00A

  • The DC voltage and ammeter can display the measured DC voltage and DC current simultaneously on the same meter screen..
  • Wide measurement voltage and current range, DC Voltage: DC0-199.9V.
  • The measured DC voltage and DC current are completely isolated within the meter..
  • Suitable for chargers, inverters, solar energy, wind driven generator, LED light measurement, etc..
Check Stock

Genuine Yamaha AC Adapter Power Supply DC12V 700mA 12.5W Model: PA-3C 12V

  • 10 Isolated Outputs: This guitar pedal power supply has 10 independent outputs: 9v 100mA x6, 9v 500mA x2, 12v 100mA x1, 18v 100mA x1. Each circuit has its own short circuit and overcurrent protection, i.e. a short circuit on one output will not affect the function of the other outputs..
  • Short circuit and overcurrent protection: In this power supply we use the best high-current output buck switching type integrated regulator circuit, this integrated chip has a complete protection circuit, capable of current limiting and thermal shutdown circuit. The other components can form an efficient regulator circuit structure with over-current protection and over-temperature protection..
  • LED Light: Each output of the pedal power supply has a blue LED indicator, and if one is faulty, the light will not turn on. This helps the musician to quickly locate the fault. The lights also help to find the power connector at night and play a good lighting effect on the stage of the performance..
  • Versatility: the pedalbord power supply has a compact body and 5 feet disconnectable AC power cord, no power adapter, plug and play, easy to carry.Wide input voltage range of 100v to 240v is ideal for international travel, equipped with 4 AC Outlet, total output power of 600w, can be u....
Check Stock

MXR Mini Iso-Brick Power Supply Guitar Effects Pedal M239

  • Four (4) 9 volt outputs with 300mA of current.
  • One (1) toggleable 9 or 18 volt output with 800mA of current.
  • Comes with a splitter cable that can be used to connect two pedals with the same voltage to a single output.
Check Stock