Top Juniper Poe Switches

YIDUOYUNCAI 6 Port PoE Switch (4*100Mbps PoE Port+2*100Mbps Uplink Port),78W,802.3af/at,VLAN,Metal Fanless,Unmanaged Plug and Play

  • ...+ Switch】4*10/100Mbps PoE+ Ports(802.3at/af)&2*10/100Mbps uplink, power budget up to 30W per PoE port and 78W for the whole..
  • 【Extend Mode】When Extend Mode is enabled, the transmission distance of POE ports can be extended to 250m at transaction rate of 10M..
  • 【Active poe switch with 802.3af/at compliant】Poe switches support poe devices and non-poe devices, But when connecting passive poe device or non-poe device,the switch can only transmit data and cannot power your device,so the connected device needs to be separately powered. Or you can use it with active poe splitter..
  • 【AI PD Detection】The poe port will intelligently judge whether the device connected to the port needs power supply. If it is a non-poe device that does not need power supply, the switch will not supply power to these devices and will not damage the device..
  • 【Plug and Play】6 Port Unmanaged Network Switch Support automatically detect devices,easy to setup with no software installation or configuration required..
  • 【Fanless design】The fanless design makes poe switch work without any noise..
  • 【Network cable short-circuit protection mechanism】POE switch is stable and has strong anti-interference ability, protect the fault caused by the short circuit of the network port.....
Check Stock

LINOVISION Mini 2 Port POE Extender IEEE 802.3af/at POE Repeater Up to 1000ft Power Over Ethernet Over Cat5/6 Cable, POE Splitter to 2 POE Devices Like IP Cameras, IP Phone, Wireless AP

  • ...t supports two levels cascade deployment, therefore total 1,000ft POE + Data transmission is provided. (The 2nd POE Extender’s POE Input should be connected to the 1st POE Extender’s Out port, not Camera port).
  • 【COMPLIANT TO IEEE802.3AF/AT STANDARD】This POE Extender works with all standard IEEE802.3af/at POE Switches/POE injectors/POE NVRs. And the POE Outputs supply power to standard POE devices (don't support 24V POE Devices) , like POE IP camera/IP phone/IP speaker. Noted: The CAMERA Port supports max 8W power consumption and the OUT Port supports max 15W. The max bandwidth is 100Mbps. As the distance increases, the power and the bandwidth will decrease..
  • 【EASY TO CONFIGURE IP CAMERA ON SITE】By interting this PoE-Extender02 to an existing PoE cable, installers can use laptop or CCTV Tester to easily adjust camera angle and configure IP.
  • 【PLUG-N-PLAY INSTALLATION】Plug-n-Play, no configuration or setup is required. With compact dimension ( 3.1”* 2” * 1”), enough to fit many junction boxes or outdoor waterproof enclosures..
Check Stock

TP-Link EAP245 V3 | Omada AC1750 Gigabit Wireless Access Point | Business WiFi Solution w/ Mesh Support, Seamless Roaming & MU-MIMO | PoE Powered | SDN Integrated | Cloud Access & Omada App | White

  • Superior Speeds with MU-MIMO — Designed with the latest 802.11ac Wave 2 MU-MIMO technology, the EAP245 reliably delivers dual-band Wi-Fi speeds up to 1750 Mbps to multiple devices simultaneously..
  • Integrated into SDN — Omada Software Defined Networking integrates APs, switches & gateways w/ several control options offered - Hardware Controller, Software Controller & Cloud-Based Controller (Contact TP-Link for CBC Details). Standalone mode applies..
  • Cloud Access — Remote Cloud access and Omada app brings centralized cloud management of the whole network from different sites—all controlled from a single interface anywhere, anytime..
  • SDN Compatibility — Make sure your devices/controllers are equipped with SDN firmware. (Or upgradable). SDN controllers work only with SDN Access Points, Switches & Gateways. Non-SDN controllers work only with non-SDN APs. Details found on TP-Link website..
  • Advanced Wireless Tech — Supports Mesh WiFi, Seamless Roaming, Band Steering, Airtime Fairness and Beamforming technologies..
  • Multiple PoE Options for Easy Installation — EAP245 supports both 802.3af/at PoE and Passive PoE power supply, can be either powered by a PoE switch or the provided PoE adapter, making deployment effortless and flexible..
Check Stock

YIDUOYUNCAI 11Port PoE Switch,8 Port 100Mbps PoE+2*1000Mbps Uplink Port and1Gigabit SFP Slot,150W,802.3af/at,Metal Fanless,Unmanaged Plug and Play

  • ...ith 8 100M port PoE + 2 1000M Uplink port+ 1 SFP port, 8×PoE ports providing up to 30W per port, total PoE budget 150W, 2 gigabit ethernet Uplink Port for connecting NVR and Internet , etc..the SFP slot can choose the optcial model with 2km,10km,20km,40km...etc..
  • 【Active poe switch with 802.3af/at compliant】poe switches support poe devices and non-poe devices, but when connecting passive poe device or non-poe device, the switch can only transmit data and cannot power your device, so the connected device needs to be separately powered. Or you can use it with active poe splitter..
  • 【AI PD Detection】The poe port will intelligently judge whether the device connected to the port needs power supply. If it is a non-poe device that does not need power supply, the switch will not supply power to these devices and will not damage the device..
  • 【Built-in power supply】The power supply is located in the poe switch body and integrated with the switch. It is simple and light. After connecting to our AC Power Cable, the switch can transmit power to the equipment connected to the switch..
  • 【Plug and Play】Easy setup with no software installation or configuration needed.
  • 【Network cable short-circuit protection mechanism】POE switch is stable and has strong ....
Check Stock

LoveRPi Compact PoE HAT with PWM Fan Controller for Raspberry Pi 4

  • ...ized footprint. Must be used with a standards compliant IEEE 802.3af PoE or 802.3at PoE+ switch that complies with Section 33.4.1 for power sourcing equipment (PSE) electrical isolation. "Passive PoE" (DC 24V or 48V) is not standards compliant and may cause damage to equipment if connected improperly. Some Ubiquiti switches are not properly isolated and require isolated PoE HATs..
  • GROUND LOOPS WARNING: Do not use this device with grounded USB peripherals, HDMI displays, and attachments. Please use the professional PoE model with isolation transformer to prevent electrical loops. In non-controlled PoE applications, ALWAYS use the professional PoE model..
  • INTEGRATED PWM FAN CONTROLLER: Based on the EMC2301 SMBus compliant fan controller, this PoE HAT is fully programmable over I2C to control standard 4-pin PWM fans. Set user-space or device-tree based temperature or event triggers for complete fan control from off to maximum RPM. Fan speed tach also provides stall detection, spin-up control, and ramp rate control with 1% accuracy from 500-16K RPM..
  • VENTILATED CASE WITH FAN HIGHLY RECOMMENDED: Do not use this product in an enclosed case without active air circulation. Airflow around the HAT and Raspberry Pi 4 Model B ensures performance and stable operatio....
Check Stock

TP-Link EAP265 HD | Omada Enterprise AC1750 Gigabit Wireless Access Point for High-Density Deployment | Support Mesh, Seamless Roaming & MU-MIMO | PoE Powered | SDN Integrated, Cloud Access &Omada App

  • High-Density Connectivity — MU-MIMO, Load Balance & professional antennas improve capacity in dense environments to connect more devices simultaneously..
  • Integrated into Omada SDN — Omada's Software Defined Networking (SDN) platform integrates network devices including access points, switches & gateways with multiple control options offered - Omada Hardware controller or Omada Software Controller. Standalone mode also applies..
  • Cloud Access — Remote Cloud access and Omada app brings centralized cloud management of the whole network from different sites—all controlled from a single interface anywhere, anytime..
  • SDN Compatibility — For SDN usage, make sure your devices/controllers are either equipped with or can be upgraded to SDN version. SDN controllers work only with SDN Access Points, Switches & Gateways. Non-SDN controllers work only with non-SDN APs. For devices that are compatible with SDN firmware, please visit 'From the manufacturer - Q&A' section or TP-Link website..
  • Advanced Wireless Tech — Support Mesh WiFi, Seamless Roaming, Band Steering, Airtime Fairness and Beamforming technologies..
  • Multiple PoE Options for Easy Installation — Support both 802.3af/at PoE and Passive PoE power supply, can be ei....
Check Stock

TRENDnet 8-Port Hardened Industrial Unmanaged Gigabit PoE+ DIN-Rail Switch, TI-PG80, 200W Full PoE+ Power Budget, 16 Gbps Switching Capacity, IP30 Rated Network Switch, Lifetime Protection, Black

  • ETHERNET PORT INTERFACE: 8 x Gigabit PoE+ Ethernet ports.
  • FULL POE+ POWER BUDGET & SWITCHING CAPACITY: The Gigabit PoE+ switch supplies up to 30 Watts of PoE / PoE+ power per port with a 200 Watt PoE power budget and allows for a 16 Gbps switching capacity..
  • DIN-RAIL & WALL MOUNT KIT: This 8-Port Gigabit PoE+ network switch comes with an integrated DIN-Rail mount and mounting hardware..
  • EXTREME TEMPERATURE SWITCH: The metal hardened IP30 rated Gigabit PoE+ Ethernet switch is equipped with a rugged IP30 rated enclosure and designed to withstand a high degree of vibration, shock, protection against ESD/EMI/surge, and operate with a wide temperature range (- 40 – 75 °C (- 40 - 167 °F)) for harsh environments..
  • REDUNDANT POWER: The 8 port switch has dual redundant power inputs with overload current protection (power supply sold separately: model: (TI-S24048).
  • TRENDnet LIFETIME PROTECTION: All metal TRENDnet switches come with lifetime manufacturer protection..
Check Stock

MokerLink PoE Switch, 6 Port and 10 Port PoE Switch, Support IEEE802.3af/at, Fanless Metal Plug & Play

  • 6 Port PoE Switch: 4 Port PoE+, 2 Port uplink, 100Mbps, 78W.
  • 10 Port PoE Switch: 8 Port PoE+ 100Mbps, 2 Port Gigabit Uplink, 120W.
  • Plug and Play, just plug in the power cord, connect the ethernet cable directly to the device, can be used without configuration..
  • Extend function: Both switches support extended functions, port isolation, etc..
  • Widely Used: Built-in Industrial Power Supply. Durable Metal housing. LED indicator lights. Widely used in IP cameras, Wireless Access Point, Computer Networks devices, etc. 100% Satisfaction Guarantee - 30-day Money-Back Guarantee with 1 Year Warranty..
Check Stock

MokerLink PoE Switch, 4 Port PoE+, and 8 Port PoE+, Support IEEE802.3af/at, Fanless Metal Plug & Play

  • Include POE-F042F (4 PoE+ Port, 2 Uplink, 100Mbps), and POE-F082GD ( 8 PoE+ Port 100Mbps, 2 Gigabit Uplink).
  • Built-in power supply makes installation easier. Support IEEE 802.3af/at, each port max power supply reached 30W..
  • Plug & Play: Support Power Detection function, automatically detect devices, can be compatible with non-POE devices to provide data connectivity. Plug and Play, just plug in the power cord, connect the ethernet cable directly to the device, can be used without configuration..
  • Extend function: Both switches support extended functions, port isolation, etc..
  • Widely Used: Built-in Industrial Power Supply. Durable Metal housing. LED indicator lights. Widely used in IP cameras, Wireless Access Point, Computer Networks devices, etc. 100% Satisfaction Guarantee - 30-day Money-Back Guarantee with 1 Year Warranty..
Check Stock

TRENDnet 6-Port Fast Ethernet PoE+ Switch, 4 x Fast Ethernet PoE Ports, 2 x Fast Ethernet Ports, 60W PoE Budget, 1.2 Gbps Switch Capacity, Metal, Lifetime Protection, Black, TPE-S50

  • ETHERNET PORT INTERFACE 4 x Fast Ethernet PoE+ ports and 2 x Fast Ethernet ports.
  • POE POWER BUDGET & SWITCH CAPACITY: This PoE+ switch supports both PoE (802.3af) and PoE+ (802.3at) devices with a 60 W PoE power budget that delivers data and power over existing Ethernet cables to Power over Ethernet (PoE) devices such as access points, VoIP phones, and IP Cameras. The 6-port fast Ethernet PoE+ network switch provides 1.2 Gbps switching capacity to support edge network installations..
  • COMPACT FANLESS DESIGN With a compact and lightweight rugged metal housing design this desktop switch is well-suited for desktop installations Its fanless design is ideal for quiet environments that require silent operation.
  • DATA TRANSFER RATE Ethernet 10 Mbps (half duplex) 20 Mbps (full duplex) Fast Ethernet 100 Mbps (half duplex) 200 Mbps (full duplex).
  • OPERATING TEMPERATURE This 6-port fast Ethernet PoE+ network switch is rated with an operating temperature range of 0 – 40 °C (32 - 104 °F).
  • TRENDnet LIFETIME PROTECTION: All metal TRENDnet switches are backed by our lifetime TRENDnet Manufacturer Protection. Renewed or refurbished products come with a 90 day Amazon Renewed Guarantee..
Check Stock

TP-Link EAP225 V3 | Omada AC1350 Gigabit Wireless Access Point | Business WiFi Solution w/ Mesh Support, Seamless Roaming & MU-MIMO | PoE Powered | SDN Integrated | Cloud Access & Omada App | White

  • ...s with MU-MIMO — Designed with the latest 802.11ac Wave 2 MU-MIMO technology, the EAP225 reliably delivers dual-band Wi-Fi speeds up to 1350 Mbps to multiple devices simultaneously..
  • Integrated into Omada SDN — Omada's Software Defined Networking (SDN) platform integrates network devices including access points, switches & gateways with multiple control options offered - Omada Hardware controller, Omada Software Controller or Omada cloud-based controller (Contact TP-Link for Cloud-Based Controller Plan Details). Standalone mode also applies..
  • Cloud Access — Remote Cloud access and Omada app brings centralized cloud management of the whole network from different sites—all controlled from a single interface anywhere, anytime..
  • SDN Compatibility — For SDN usage, make sure your devices/controllers are either equipped with or can be upgraded to SDN version. SDN controllers work only with SDN Access Points, Switches & Gateways. Non-SDN controllers work only with non-SDN APs. For devices that are compatible with SDN firmware, please visit 'From the manufacturer - Q&A' section or TP-Link website..
  • Advanced Wireless Tech — Supports Mesh WiFi, Seamless Roaming*(Omada Mesh & Seamless Roaming require the use of Omada SDN controllers), Band Steering,....
Check Stock

MokerLink PoE Switch, 6 Port PoE Switch, and 5 Port Gigabit PoE Switch, 78W High Power, Support IEEE802.3af/at, Fanless Metal Plug & Play

  • 6 Port PoE Switch: 4 PoE+ Port, 2 uplink port, 100Mbps, 78w.
  • 5 Gigabit Port PoE Switch: 4 Gigabit PoE+ Port, 1 Gigabit uplink, 1000Mbps, 78w.
  • Plug & Play: Support Power Detection function, automatically detect devices, can be compatible with non-POE devices to provide data connectivity. Plug and Play, just plug in the power cord, connect the ethernet cable directly to the device, can be used without configuration..
  • Extend function: Both switches support extended functions, port isolation, etc..
  • Widely Used: Built-in Industrial Power Supply. Durable Metal housing. LED indicator lights. Widely used in IP cameras, Wireless Access Point, Computer Networks devices, etc. 100% Satisfaction Guarantee - 30-day Money-Back Guarantee with 1 Year Warranty..
Check Stock