Top Keyed Shaft

Martin SDS 1 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1\ Bore, 2.187\ OD, 1.37\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin E 1 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1\ Bore, 3.834\ OD, 2.62\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin E 2 3/8 Quick Disconnect Bushing, Ductile Iron, Inch, 2.38\ Bore, 3.834\ OD, 2.62\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin JA 1 1/4 Quick Disconnect Bushing, Ductile Iron, Inch, 1.25\ Bore, 1.375\ OD, 1.06\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

3pcs/Pack Brass Mini Ball Valve Shut Off Switch 1/4" NPT Male x 1/4 INCH NPT Female Rated to 600WOG for Water Air Compressor Etc

BRAND NEW TRUE 5HP COMPRESSOR DUTY MOTOR, 56HZ FRAME, 3450RPM, 7/8" SHAFT DIAMETER.
22 FULL LOAD AMP AT 230V, THIS MOTOR NOT SUITED FOR INCOMING VOLTAGE LESS THAN 208V.
CCW (COUNTER CLOCKWISE) SHAFT ROTATION WHEN VIEWED FROM THE SHAFT END. SHAFT ROTATION IN NOT REVERSIBLE.
2.25" SHAFT LENGTH, KEYED SHAFT, 60HZ, 1.0 SERVICE FACTOR.
WIRING INFO SHOWN ON NAMEPLATE, PROFESSIONAL INSTALLATION REQUIRED.

Martin SH 32MM Quick Disconnect Bushing, Sintered Steel, Metric, 32 mm Bore, 47.52 mm OD, 33.33 mm Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin SDS 35MM Quick Disconnect Bushing, Sintered Steel, Metric, 35 mm Bore, 55.54 mm OD, 46.03 mm Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin SF 11/16 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 0.68\ Bore, 3.125\ OD, 2.06\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin SD 15/16 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 0.93\ Bore, 2.187\ OD, 1.81\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin J 100MM Quick Disconnect Bushing, Ductile Iron, Metric, 100 mm Bore, 130.75 mm OD, 114.3 mm Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin SK 1 15/16 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1.94\ Bore, 2.812\ OD, 1.93\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Martin SDS 1 5/16 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1.31\ Bore, 2.187\ OD, 1.37\ Length

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.