Top Large Diameter Bead Reamer

7/8\ Expansion Reamer, Carbide Tipped, Tapered Shank, 56067, USA Made

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

Material: 5/8 bridge reamer is made of high-quality M2 HSS steel, with high toughness, high-temperature resistance, corrosion resistance and long service life. Compared to other commonly used low-grade high-speed steels, M2 has an increased content of tungsten and molybdenum, both key elements for improved durability.
Wide Application: HSS bridge reamers can enlarge or align existing holes and are suitable for various materials such as aluminum, brass, bronze, cast iron, copper, iron, metal, nickel, plastic, steel and other structural materials Note: It requires existing holes Or a pilot hole is required.
Size Infor: Length of chucking reamer is 6.5 inch.
Safe to Use: Designed with helical flutes and safety stops to keep chips away from the operator. The safety collar stops to prevent over-penetration and loss of operator stability.
Design: The tapered tip design allows the reamer to fit into unevenly overlapping holes, aligning the bolt holes. The 5/8" bridge reamer is not a drill, it just aligns the reamer with the pre-drilled hole.

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
Morse taper shank #3, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 3/8 " flute length, Partial Flute Length Carbide.
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
2" flute length, Partial Flute Length Carbide.
Morse taper shank #4, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 7/8 " flute length, Partial Flute Length Carbide.
Morse taper shank #4, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..