Top Lippert Trailer Jacks - BuyWiseBest.com

Lippert 285324 Manual Stabilizer Jack Power Tongue Jack Crank Handle

This durable manual scissor jack crank handle is easy to use and is also used for power tongue jacks in case of power failure..
Durable crank handle that will retract most Lippert landing gear and slide out assemblies..

Fits 1,250 to 8,000 lbs. capacity trailer axles.
Compatible with: Lippert, Dexter or Al-Ko trailer axle hubs with corresponding grease seal measurements.
Provides protective barrier between the axle hub grease and the outside elements.

Fits 1,250 to 8,000 lbs. capacity trailer axles.
Compatible with: Lippert, Dexter or Al-Ko trailer axle hubs with corresponding grease seal measurements.
Provides protective barrier between the axle hub grease and the outside elements.

Stabilize your Trailer in less than 60 Seconds. Made in USA System Stabilizes Parked Travel, Camper, or Fifth Wheel Trailer.
Trailer Must Have 4 Jacks, 2 front and 2 Rear for the system to be installed. Includes the two required Foot Plates plus two additional so all jack footplates will match..
Installs Permanently so there is nothing to setup or store. Approximately 2-3 hour install...
Works on both 5th Wheels and Travel Trailers with existing stabilizer jacks. If you have an Auto Leveling system Please check out our Item C..
Eliminates Need for Tripod. Between Wheel Chocks, and Slide Out Jacks.

3,500 lbs Idler Trailer Axle (Capacity 3.5K).
Internal Wiring System To ensure seamless design Protect brake wires from wear and tear.
Replaces TK Trailer Parts, AL-KO, Hayes, and Lippert Axles.
Underslung - Axle is welded with spring seats on the bottom Allows for lower ride height For optimal usage, use with double eye springs.
High Strength Straight Steel Axle Tube Construction to ensureA better highway experience.

M-PARTS ELECTRIC TRAILER BRAKES – Two Trailer Brake Drums 8 on 6.5” and two 12x2 Electric Brakes for 7000 lbs Axle with Hardware, Replaces Dexter and Lippert.
DIMENSIONS - 12” x 2” Trailer Brakes and 8 on 6.5” Brake Drums.
TRAILER BRAKE BOLT PATTERN - Mounting flange bolt pattern: 5-bolt (each brake).
HARDWARE - inner bearing, outer bearing, Grease seal, EZ Lube Dust cap, Lug nuts, Cotter Pin, Washers.
M-PARTS AUTO- M-Parts Auto specializes in trailer parts & accessories using the highest quality materials.

2-Pack (2LH & 2 RH) TruRyde 10" x 2 1/4" self-adjusting electric brake assemblies.
4 Hole Mounting for 3,500 lbs. trailer axle. Comes with mounting nuts, and lock washers.
Contains 2 left and 2 right brake assembly..
Works with Al-Ko, Dexter, Lippert,and Quality Trailer Axles.
Geniune TruRyde Brakes. TruRyde parts are manufactured to automotive standard in ISO/TS-16949 registered factory..

... Air Ride Technology: Protects your truck, camper trailer and the contents with a smoother, safer tow. Heavy loads, just add air. The cure for choppy, bouncy, buckled, rough & busted up roads. No more booms, bangs and jerks when towing with your gooseneck. 2 Gooseneck Pin Box Option to Choose From: Choose Lippert 1621, 0719 or Rhino Box, as well as the Lippert 1716, 1116, 0115, FabEx 500, 503, 520, 530, 560..
Includes complete Replacement Gooseneck pin box along with Shocker Gooseneck Surge air hitch with built in airbag, replacement inner tube stem & 24,000 lb Shift Lock gooseneck coupler for 2-5/16" ball. Fits 2-5/16" gooseneck hitch balls: & has 3 height adjustment holes. Does not include chains..

Best Performing Stabilizer System, ONLY 60 SECONDS to SETUP, No need to crawl under trailer, No Storage Space Needed, Made in USA,.
Only Available in Dark Grey. Permanently installed in 2-3 hours..
Works on 5th Wheels and Travel Trailers with existing stabilizer jacks. If your trailer has an auto leveling system Please order our Item C...
Eliminates Need for Tripod. Between Wheel Chocks, and Slide Out Jacks or any other parked trailer stabilizers.

2-Pack of TruRyde 12" x 2" self-adjusting electric brake assemblies. Contains 2 left and 2 right brake assembly..
5 Hole mounting for 5,200 lbs., 6,000 lbs., and 7,000 lbs. trailer axles..
Comes with mounting bolts, nuts, and lock washers.
Works with Al-Ko, Dexter, Lippert,and Quality Trailer Axles.
Geniune TruRyde Brakes. TruRyde parts are manufactured to automotive standard in ISO/TS-16949 registered factory..

General duty 12-1/4” X 3-3/8” Trailer Electric Brake Assembly that works with 8,000 lbs Dexter and Lippert (aka LCI) Trailer Axles.
4” bolt circle, 3-7/8” center hole diameter.

General duty 12-1/4” X 3-3/8” Trailer Electric Brake Assembly that works with 10,000 lbs Dexter and Lippert (aka LCI) Trailer Axles.
7 Bolt Holes, 5.5" Bolt Circle, 4.5” Center Hole diameter.