Top Low Pass Filter

Sound Storm Laboratories LOPRO10 10 Inch Powered Under Seat Car Audio Subwoofer - 1200 Watts Max Built-in Amplifier Low Profile Remote Subwoofer Control for Truck Boxes and Enclosures

  • Built-in Amplifier - With a MOSFET power supply you get improved switching speeds, better performance with less power from the driver, lower gate-to-drain feedback capacitance, lower thermal impedance for higher switching frequencies.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes above the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the LOPRO10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low-Level Inputs - Line level inputs (RCA inputs / low-level inputs) use RCA interconnect cables to link the LOPRO10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Check Stock

BOSS Audio Systems AR1500M Car Amplifier - 1500 Watts Max Power, 2 4 Ohm Stable, Class AB, Monoblock, Mosfet Power Supply, Remote Subwoofer Control

  • POWER: Maximum Power Output of 1500 Watts at 2 Ohms into one channel. MAX Power Output of 750 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to.
  • HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the AR1500M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the AR1500M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • LOW-PASS CROSSOVER: A low-pass filter is an electronic circuit that removes all the notes below the filter’s frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • SWITCHABLE BASS BOOST: Switchable Bass Boost allows you to boost the low bass +18db..
Check Stock

Planet Audio AC2500.1M Monoblock Car Amplifier - 2500 Watts Max Power, 2/4 Ohm Stable, Class A/B, Mosfet Power Supply, Remote Subwoofer Control

  • POWER: Maximum Power Output of 2500 Watts at 2 Ohms into one channel. Maximum Power output of 1250 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to.
  • HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. This input will be used to connect the AC2500.1M to your factory radio or aftermarket radio that does not have low-level (RCA) inputs..
  • LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the AC2500.1M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • LOW-PASS CROSSOVER: A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. A low-pass filter will primarily keep high notes out of your subwoofer(s).
  • VARIABLE BASS BOOST: Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Check Stock

Anti-Interference High Reliability 433MHz New Denoise Bandpass Filter BPF SMA Interface for Block Frequencies

  • Power supply EMI filter is a kind of reactance-type low-pass filter, installed at the power supply input of electronic equipment..
  • It can inhibit noise transmitted through grid power cable, and can inhibit high-frequency interference signals generated by the electronic device itself..
  • High quality imported components provide obvious filtering effect..
  • EMI has become a must have device installed in electronic equipment..
Check Stock

BOSS Audio Systems CUBE10 Car Subwoofer and Amp Package – Built-in Amplifier, 10 Inch Subwoofer with Passive Radiator, Remote Subwoofer Control

  • ...600 Max watt amplifier powers the 10” subwoofer.
  • Passive Radiator – A driver unit that has its motor structure (magnet) removed, becomes a passive diaphragm. As a result, there is no Chuffing that you would generally get with a ported box, thus enriching the BASS & making the system more linear.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the CUBE10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Phase Control - Phase control lets you adjust the speaker phase with the amplifier if your speakers or subwoofer are hooked up “out of phase”.
  • Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the CUBE10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Check Stock

BOSS Audio Systems Elite SLIM10 Amplified Car Subwoofer - Low Profile, 10 Inch Subwoofer, Remote Subwoofer Control, for Vehicles Needing Bass with Limited Space

  • ...im design, there are a few installation options.
  • Pulse Width Modulated - PWM simplifies power supplies. It controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. Efficiency. Increased reliability.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the SLIM10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the SLIM10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
  • Specs - Dimensions: 13.58” x 10.43” x 3.15”, Weight: 10.45 lbs. Phase control. LED status indicator. Thermal, Short and Overload Protection Circuits. ....
Check Stock

Rockville RockGhost Active Powered 8 Hidden Car Subwoofer Sub For 15 /16 /17 Full Size Spare Tire

  • Features: Rockville RockGhost Powered Car Subwoofer (Amplifier built in). Sub Fits Inside Spare Tire Seamlessly (Goes on top of spare tire so you can....
  • For Full Size Spare Tire Wheel Sizes of 15"/16"/17". Extremely loud (loud enough to vibrate your mirrors). Super clean sound that is musical and will....
  • PWM MOSFET power supply amplifier built in. Low level RCA inputs. 8” high excursion Subwoofer. Reverse mounting design. Plug and play installation....
  • Wired 20 foot dash remote with adjustable gain, bass boost, low pass crossover filter, and phase control. Deep and clear bass frequency. Auto turn on....
  • Phase Switch: 0° or 180°. Low Pass Filter: 50Hz - 150Hz. Frequency response: 20 Hz – 250 Hz. Bass Boost: 0 - 12dB @ 45Hz. 20 Hz Subsonic Filter.....
Check Stock

BOSS Audio Systems BASS10 Amplified Car Subwoofer - Low Profile, 10 Inch Subwoofer, Remote Subwoofer Control, for Vehicles Needing Bass with Limited Space, Remote Subwoofer Control

  • ...im design, there are a few installation options.
  • Pulse Width Modulated - PWM simplifies power supplies. It controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. Efficiency. Increased reliability.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BASS10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BASS10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
  • Specs - Dimensions: 14” x 12.3” x 3.3”, Weight: 11.35 lbs. Phase control. LED status indicator. Thermal, Short and Overload Protection Circuits. High ....
Check Stock

Rockville KRYPTON F2 2400w Peak/600w RMS 4 Channel Amplifier Car Stereo Amp

  • Rockville KRYPTON F2 2400w Peak/600w Dyno-Certified RMS 4 Channel Amplifier Car Stereo Amp..
  • Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). 2 Ohm: 150 Watts x 4 Channels.
  • 4 Ohm Bridged: 300 Watts x 2 Channel. Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). 2 Ohm: 600 Watts x 4 Channels. 4 Ohm: 400 Watts x 4 Channels. 4 Ohm Bridged: 1200 Watts x 2 Channels..
  • All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers. All channels on the amplifier are bridgeable. Digital Voltage Display on Amp..
  • Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Adjustable Subsonic Filter: 15Hz -40Hz (This filter is on the HPF knob). Adjustable Low Pass Filter: 40Hz – 4KHz. Adjustable Band Pass Filter: 15 Hz - 4 kHz (use both the HPF and LPF filter). Adjustable High Pass (Subsonic) Filter: 15 Hz - 4 kHz.
Check Stock

BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space

  • ...lt-in 800 Max watt amplifier powers the subwoofer.
  • Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
  • Specs - 12 inches in Depth, 9. 3 inches in Width and 2. 9 inches in Height.
  • - BOSS Audio Systems provides a Powerful 3 Year Platinum Online Dealer so long as the p....
Check Stock

Rockville Krypton F1 1600w Peak / 400w RMS 4 Channel Amplifier Car Audio Amp

  • Rockville KRYPTON F1 1600w Peak / 400w Dyno-Certified RMS 4 Channel Amplifier Car Audio Amp..
  • Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). 2 Ohm: 100 Watts x 4 Channels 003c1% THD+N. 4 Ohm: 70 Watts x 4 Channels 003c1% THD+N..
  • 4 Ohm Bridged: 200 Watts x 2 Channel. Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). 2 Ohm: 400 Watts x 4 Channels. 4 Ohm: 280 Watts x 4 Channels. 4 Ohm Bridged: 800 Watts x 2 Channels..
  • All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers. All channels on the amplifier are bridgeable. Digital Voltage Display on Amp. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry..
  • Adjustable Subsonic Filter: 15Hz -40Hz (This filter is on the HPF knob). Adjustable Low Pass Filter: 40Hz – 4KHz. Adjustable Band Pass Filter: 15 Hz - 4 kHz (use both the HPF and LPF filter). Adjustable High Pass (Subsonic) Filter: 15 Hz - 4 kHz. 2CH/4CH Input Mode Switch. 8 Volt Preamp Circuitry.
Check Stock

BOSS Audio Systems BASS8 8 Inch Under Seat Powered Car Subwoofer – 800 High Output, Low Profile, Built in Amplifier, for Truck, Boxes and Enclosures, Remote Subwoofer Control

  • ...im design, there are a few installation options.
  • Pulse Width Modulated - PWM simplifies power supplies. It controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. Efficiency. Increased reliability.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BASS8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BASS8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
  • Phase Control - Phase control lets you adjust the speaker phase with the amplifier if your speakers or subwoofer are hooked up “out of phase”.
Check Stock