Top Male Elbow Fitting
Roastove Propane Elbow Adapter with Extension Hose 12 FT RV 1/4 Quick Connect Propane Hose with Elbow Fitting to Blackstone 17 /22 Griddle…
- 【COMPATABILITY】Suit for connecting Blackstone 17"/22" Griddle directly to RV's propane supply, convert.Also can take off the elbow adapter and....
- 【STANDARD FITTING】1/4" male quick-disconnect plug x (Propane elbow adapter fitting for Blackstone 17"/22" Griddle + 3/8" female flare swivel....
- 【COST EFFECTIVE】You do not need a regulator any more ,allows your Blackstone Griddle to connect to the low pressure system on a travel trailer or....
- 【DURABLE】Solid brass construction ,12 feet durable rubber hose..
- 【EASY TO INSTALL】Connect directly by hands no need tools..
Check StockMaxLine Rapid Air 45 Degree 1/2' NPT Pipe Thread Brass Street Elbow Fitting 50131
- This is a solid brass street elbow that features 1/2" male NPT threads on one side as well as 1/2" female NPT on the opposite side..
- This part is produced by RapidAir for the 3/4" MaxLine air piping systems outlets to install an air coupler at a 45 degree angle, but can be used for other applications as well..
- 1/2" Threads Measure about 3/4" in diameter if measured with a tape measure..
Check StockHromee Extended Tank Drain Assembly Kit with 10 Inch Braided Steel Hose 1/4 Inch Drain Valve and Elbow Fitting for Air Compressor
- ...tank to prevent water buildup. Hromee Extended Tank Drain Valve Assembly is perfect for the compressor tank..
- The valve kit comes with a 10” flexible braided steel drain hose which prevents breaking and kinks. 1/4in. NPT threads at both ends matches 1/4in. NPT male brass fittings. Max working pressure: 175 PSI. Blasting Pressure: 475 PSI. Max Temperature: 200 degrees F..
- This 1/4 in. ball valve is made of chrome-plated brass for higher corrosion resistance than regular brass or steel, and has a lever handle for on/off to control the flow between pipes, tubes, or hoses. The rubber-wrapped handle is designed for easy-use and labor-saving. This ball valve is pressure rated to 300 PSI at a maximum operating temperature of 212 degrees F..
- The extended tank drain kit offers a 1/4 in. elbow with pre-applied thread sealant, allowing for attaching the additional drain hose or elbow. A thread seal tape is equipped with this drain kit for multiple use to prevent leaks..
- There is a Hex bushing brass adapter which is 3/8" Male x 1/4" Female for connecting two pipes or with different....
Check StockVent Systems 4\ inch Elbow 90 degree Duct Pipe Connector Flexible Round Tube Ventilation Hose ABS Plastic 100 mm
- Made of High Quality ABS Plastic and perfectly designed for home improvement, DIY and Trade.
- Flexible Coupling, Male Fitting for a 4 Inch pipe - Compatible with Round Pipe, Flexible Hose and other pipe, 90 degree elbow.
- Easy to install - fit perfectly with any other pipe, vent and connector. Push-fit duct and fittings together..
- Elastic 90 degree Elbow Ducting Pipe Connector is simple to adjust and connect with pipe..
- Vent Systems products are made to be used for home improvement, office improvement. They are portable, high quality and long durability..
Check StockBrennan N2501-04-02-SS Stainless Steel Compression Tube Fitting, 90 Degree Elbow, 1/4\ Tube OD x 1/8\ NPT Male
- 90-degree elbow for connecting two pipes or fittings at an angle.
- Push-to-connect fitting connects to pipes or tubing on one end and has an NPT male connector on the other.
- Made of stainless steel for resistance to scaling and corrosion.
- Double ferrule fitting reduces possibility of leakage.
- Meets ISO 9001:2008 quality assurance standards.
Check StockBUILDERS BEST 111718 Elbow Kit, 4-inch by 8-foot, Silver
Check StockEaton Aeroquip 2062-8-6S Steel Flared Tube Fitting, 90 Degree Elbow, 9/16\ Male JIC x 3/4\ O-Ring Boss Male
- 90-degree flared tube fitting elbow for connecting tubes at a 90-degree angle.
- Male 3/4-16 SAE O-ring threads on one end and male 9/16-18 JIC threads on the other for use with 3/8" OD tubes.
- Zinc-plated steel for strength, durability, and resistance to corrosion.
- Meets MIL-SPEC MIL-F-18866 and SAE J514 standards for hydraulic tube fittings.
Check StockKWODE Commercial Wall Mount Faucet Installation Kit, Wall Mount Kitchen Faucet Mount Kit Backsplash Mount Set for Stainless Steel Commercial Kitchen Prep & Utility Sink
- Commercial Faucet Installation Kit:This faucet installation kit connected size is G1/2 male(also called 1/2 IPS), not 1/2” NPT, fitting wall commerical faucets with G1/2 female end..
- LEAK-PROOF DESIGN: It is one-piece construction for no leaking, plastic washers and rubber washers are used together for better leak-proof effect..
- EASY TO INSTAL :Connect the longer end to the back of wall mount faucet,the shorter end to water line,aganist washes at the back of stainless steel sink by lock nuts to secure faucet.(tips please use the water tape to avoid leakage).
- INSTALLATION KIT FOR BACKSLASH MOUNT FAUCET:This elbow adapter with 1/2 IPS male ends is designed to install a wall mount commerical faucet on the backsplash of stainless steel commercial kitchen prep & utility sink, which can save you space and increase the service life of the water supply line..
- SOLD IN PAIR: Comes with 90 degree angled elbow joint x 2, lock nut x 2, stainless steel washer x 2 and rubber washer x 2..
Check Stock2 Pack - 316 Stainless Steel 1/4 NPT Female to 1/4 NPT Female Straight Hex Coupler/Coupling for Air, Liquid or Hydraulic Fitting - Industrial Air Tool Hose 1/4 Inch Coupling
- 90-degree elbow for connecting two pipes or fittings at an angle.
- Fitting has a JIC flared male connector on one end and an NPTF male connector on the other.
- Made of forged steel for weldability, rust resistance, and durability.
- Operating temperature ranges from -63 to 400 degrees F.
- Meets SAE standard J514 for quality assurance.
Check StockAnderson Metals - 00069-1212 Brass Tube Fitting Elbow 3/4 Compression x 3/4 Male Pipe
- 90-degree elbow for connecting two pipes or tubes at an angle.
- Fitting connects to pipes or tubing on one end and an NPT male connector on the other.
- Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
- Operating temperatures range from -65 to 250 degrees F.
- Suitable for copper, brass, aluminum, and steel tubing.
Check StockInstallation kit for Wall Mount Commercial Faucet,backsplash Mount Set for Stainless Steel Commercial Kitchen Prep & Utility Sink
- 【INSTALLATION KIT FOR BACKSLASH MOUNT】This elbow adapter with 1/2 IPS male ends is designed to install a wall mount commerical faucet on the backsplash of Stainless Steel Commercial Kitchen Prep & Utility Sink.
- 【1/2 IPS STRAIGHT THERAD】it is NOT 1/2 NPT,it's 1/2 IPS which is also called G1/2,fitting wall commerical faucets with G1/2 female end.
- 【LEAK FREE】its one-piece construction for no leaking.
- 【EASY TO INSTAL】Connect the longer end to the back of wall mount faucet,the shorter end to water line,aganist washes at the back of Stainless Steel sink by lock nuts to secure faucet.
- 【SOLD IN PAIR】comes with 90 degree angled elbow joint x 2,lock nut x 2,plastic washer x 2 and rubber washer x 2.
Check Stock12FT Quick-Connect RV Propane Hose with 1/4 Safety Shutoff Valve and 1/4 Male Full Flow Plug Low Pressure Quick Disconnect Propane Hose with Elbow Adapter for 17 and 22 Blackstone Griddles
- 【 Cost-Effective 】Product contains: 12FT Quick-Connect RV Propane Hose with 1/4" Safety Shutoff Valve and 1/4" Male Full Flow Plug, Low Pressure....
- 【 Perfect Length 】 The 12FT Male/Female Quick-Connect RV Propane Extension Hose Compatible with Blackstone 17"/22" Griddles can be put where you....
- 【 Applications 】The 12 Feet propane extension hose with 1/4 quick connect Shutoff valve and 1/4 quick connect full-flow male plug & Low Pressure....
- 【 Premium Material 】The 1/4 inch Shutoff Valve and 1/4" Male Full Flow Plug,Elbow Adapter Fitting are made of 100% Solid Brass Fittings,The 12feet....
- 【 Quality Commitment 】100% Full refund. If you don’t like our product or they are not what you want, please don’t rush to leave a comment,....
Check Stock