Top Male Nipple Fittings For Plumbing

Class A Customs | Under Mount 20 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit UM-2000-BPK

  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 13” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Th....
Check Stock

Legines Brass Pipe Fitting Long Nipple, 1/8' NPT Male x 1/8' NPT Male Extender Straight Connector, 1-1/2'Length 1200psi (Pack of 5)

  • Long nipple for connecting two threaded pipes and extending pipe length.
  • 1/8" Male National Pipe Taper (NPT) threads for connecting to 1/8" female threaded pipes.
  • Legines pipe fittings are made of CA360 or CA377 brass, not ordinary copper alloy, and meet SAE standard, have dryseal threads, forgings & extruded..
  • Operating pressure of our fittings is up to 1200psi, more higher than other general fittings. Temperatures range from -53 to 121 degrees C (-65 to 250 degrees F).
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
Check Stock

Class A Customs 13 Gallon Water Tank & Plumbing Kit T-1300-BPK

  • ...Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • 13 GALLON TANK MEASUREMENTS 21” x 9” x 16”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adapter (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adapter (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adapter (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Eastman 48036 Flexible Faucet Connector Supply Line, Braided Stainless Steel, Delta Style, 3/8-inch Outside Diameter (OD) Male Compression Outlet X 3/8\ Compression Inlet, 16-Inch Length

  • EZ-Fluid Plumbing Stainless Steel Braided Faucet Extension Line, Fits 3/8" Male Comp. End Fittings For Faucet, Toilet, Dishwasher, Water Filter System And More.
  • cUPC, NSF Certified Lead Free faucet supply 3/8 to 3/8 Extension.
  • Faucet 3/8" Female Compression X 3/8" Female Compression Faucet Extension Line.
  • High Burst Strength, Extra-Long Stainless Steel, No-Burst Ferrules With Double Radial Crimps For Extra Security.
  • 3/8 female compression hose x 3/8 female Comp water connector, The 3/8 female Compression End Fits 3/8" Male Comp. End Fittings.
Check Stock

Air Hose Fittings 1/4" Air Coupler & Plug Kit,36 Pieces Quick Connect Air Compressor Accessories W/Storage Case

  • Industrial type, also known as M/D type, compatible with industrial/M/D type air fittings.
  • Used for a variety of air tools such as air compressors, air blow guns, air nailers etc..
  • 1/4 inch NPT thread × 1/4 inch body size, interchangeable with most manufacturers.
  • Kit includes 10pcs Male Plugs, 10pcs Female Plugs, 4pcs Female Couplers, 4pcs Male Couplers, 4pcs Male Hex Nipple, 4pcs Female Hex Coupling..
  • Customer Satisfaction Guarantee: 30-day return guarantee is provided..
Check Stock

Class A Customs | 25 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2500-BPK-PUMP

  • 25 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS 33.5” Longest Length (not including fittings) x 10” x 17”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID V....
Check Stock

Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP

  • 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check Stock

Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP

  • 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Check Stock

Class A Customs | 30 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-3000-BPK-PUMP

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - BPA FREE - NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Gray Water Storage ||WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” (rotate tank to change height or width) Average thickness 7/32” +/- (+/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Balloon Style Threaded Female NPT Standard - fitting will be closed, to use remove inner membrane with razor knife (TWO) .5" Threaded Female NPT Standard - open fitting, unsealed.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT hook garden hose directly to tank doing so will cause tank to explode resulting in damage..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

MICTUNING RV Winterize Blowout Adapter Kit - 1/4 Male Quick Connect Plug & 3/4

  • Prevent Freezing of Water Line – This winterize blowout adapter kit helps to winterize garden hose, sprinkler systems, faucets, by blowing out water from the water lines/plumbing. It is an environmental friendly winterization way, which greatly reduce the chance of using antifreeze.
  • Trusted Quality – The fittings made of lead-free brass which contain less than 0.25% lead, care for your health and safety. It is not easy to break or deform, ensure long-lasting service time.
  • Wide Range of Uses – A quick and easy way to blow out the water lines of your RV, motorhome, camper, boat, and travel trailer, sprinkler systems, outdoor plumbing, garden hoses and more.
  • Easy Operation – Comes with a 3/4 Inch Female Garden Hose Threading for you to connect the gardening pipe. Besides, two black washers included to prevent leakage between the water tube and water tap.
  • Standard Threaded Connection – With a 1/4 inch male air compressor quick plug to a male 3/4 inch garden hose inner thread, easy attach air line to water lines or hose system. You can rotate around the Air Flow Regulation Ball Vale to open or close and adjust the air flow rate.
Check Stock

SharkBite 1 Inch x 3/4 Inch MNPT Reducing Adapter, Pack of 6, Push to Connect Brass Plumbing Fitting, PEX Pipe, Copper, CPVC, PE-RT, HDPE, U142LF

  • SHARKBITE BRASS PUSH MALE REDUCING ADAPTER: This push-to-connect fitting allows you to make a transition between a pipe and an FNPT thread quickly and easily.
  • ideal for working in tight spaces **Remove using a disconnect clip or disconnect tongs**.
  • VERSATILE: Pushfit male reducing connectors work well with PEX, CPVC, PE-RT, SDR-9 HDPE, and copper pipes.
  • large diameter fittings (1-1/4 in. to 2 in.) require a Stiffener when connecting to PEX pipe.
  • EASY TO INSTALL: The innovative push-to-connect design of the SharkBite push male reducing adapters allows for quick and easy installation, with no tools, crimping, glue, or soldering required.
  • PREFERRED BY THE PRO: SharkBite tools and fittings meet the same high standards for commercial and residential plumbing applications, combining durability and ease of use suitable for commercial repairs or home improvement projects.
  • approved for underground and behind-the-wall applications with no access panels.
  • SPECS: Made with DZR forged brass, this reducing adapter can withstand 200 degrees F and 200 PSI.
Check Stock

Hex Bushing 1 Male x 1/2 Female Brass for Repair Threaded Pipe Fitting Pack of 1

  • ENHANCED QUALITY BRASS Makes Hex Bushing Resistant to Corrosion and Safe for High Temperatures.
  • CONVENIENTLY DESIGNED TO CONNECT Pipes or Fittings of Different Diameter, Material, and End Type. Our Metal Hose Vacuum Gauge Hex Bushing have 1" Male....
  • RELIABLE FITTING of the Bushing Reducer is Provided by the Well-Machined Threads and the Relative Softness of the Brass that Enables Tighter Sealing.....
  • UNIVERSAL – our Hex Bushing can be easily Used with Water or Oil for Plumbing Applications, for Various Measurable Devices, Collectors, etc.
  • DURABLE –Our Hex Bushing don’t Deform with Time, unlike Traditional Stainless Steel Thread Bushing or Plastic Pipe Fittings. N.
Check Stock