Top Microcontroller Board

Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino

  • ... the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”)..
Check Stock

1pcs 1-Bit AC 220V Optocoupler Isolation Module

  • Output TTL level can be detected with the microcontroller. The power supply can be 3-5V.
  • the PLC input terminal of the PLC COM power supply 24V input termination of the board signal output OUT, optocoupler board GND power negative.
  • When the power module in the power of the board after the white wire frame can not touch any device .. because it is high voltage. Note the safety of electricity.
Check Stock

STLINK-V3SET Microcontrollers ST STM8 and STM32 MCU USB Swim JTAG SWD Modular Stand-Alone in-Circuit Debugger Programmer SPI I2C CAN GPIOs @XYG

  • The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and....
  • The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board..
  • The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and....
  • The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board..
Check Stock

waveshare for Raspberry Pi Pico Evaluation Kit B Include Pi Pico Board with Pre-Soldered Header,1.14inch RGB Color LCD, 10DOF IMU Sensor Module,Dual GPIO Expander,Breadboard

  • Raspberry Pi Pico Evaluation Kit inlclude Raspberry Pi Pico with pre-soldered header ,1.14inch LCD Display Module,10-DOF IMU Sensor Module,Dual GPIO Expander ,830 Quality Breadboard etc.
  • Raspberry Pi Pico Board,a tiny, fast, and versatile microcontroller board,Built Using RP2040 Microcontroller Chip Designed By Raspberry Pi.
  • 1.14" LCD Display Module for Pico ,Embedded ST7789 Driver, Using SPI Bus.
  • 10-DOF IMU Sensor Module,an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I2C bus for communication..
  • Dual GPIO Expander for Pico,Two Sets Of Standard Raspberry Pi Pico GPIO Male Headers.
Check Stock

Arduino MKR Zero with Headers [ABX00012]

  • The Central Board for your Electronic Project.
  • Powerful 32-bit Microcontroller and Micro SD Memory Card Connector.
  • Ideal for: Music, Audio processing, robotics, art installations.
  • Part of the Arduino Maker Board Family for IoT Devices, easy to configure with Arduino Software..
Check Stock

12Pcs CD74HC4067 16-Channel Analog Digital Multiplexer MUX Breakout Board Module CD74HC4067 CMOS Precise Module Compatible with DIY

  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”)..
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins..
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can t....
Check Stock

Gowoops MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY

  • Embed version of Mega 2560 CH340G/ATmega2560 - compatible with Arduino Mega 2560 board..
  • Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
  • Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
  • The board used the chip CH340G as converter UART-USB..
Check Stock

ACEIRMC 2pcs for MEGA 2560 PRO Embed CH340G/ATMEGA2560-16AU Chip with Male Pinheaders Compatible for Arduino Mega2560 Module

  • MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY.
  • Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
  • Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
  • Board for functionality similar to the compatible for Arduino Mega 2560..
  • The board used the chip CH340G as converter UART-USB..
Check Stock

sb components Raspberry Pi Pico Board with Raspberry Pi Pico GPIO Expansion Board, Multi-Purpose Raspberry Pi Pico Kit

  • Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
  • It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
  • Raspberry Pi Pico GPIO Expansion Board is used to break outall the pins and power of the Raspberry Pi Pico development board via male or female headers.
  • Raspberry Pi Pico GPIO Expansion Board allows the user to connect it to other components with the help of a jumper wire.
  • Raspberry Pi GPIO Expansion Board is specially made to work with the Raspberry Pi Pico Board.
Check Stock

Arduino MKR WAN 1310 [ABX00029]

  • The perfect IoT node and building block for adding to Lo-Ra connectivity to low power wide area IoT devices.
  • Very long battery life - the latest low power architecture means the power consumption is able to go as low as 104uA for extended battery life. It is also possible to use the USB port to supply power (5V) to the board, so you can run the board with or without batteries.
  • Local storage - On board 2MByte Flash to facilitate data logging and Over-The-Air (OTA) functions.
  • Enhanced Security - credentials and certificates are stored in the boards crypto chip, an embedded secure element.
  • Powerful - The MKR WAN1310 is based on the Atmel SAMD21 microcontroller and a Murata CMWX1ZZABZ Lo-Ra module.
Check Stock

GY-AS3935 Lighting Sensor Module SPI I2C MA5532-AE Lighting Strike Thunder Storm Distance Detector Breakout Board

  • Reference link: https://tinyurl(dot)com/AS3935-light-detector.
  • Video link: https://youtu(dot)be/oXqSIyaHR_I.
  • The splitter uses an inductor (antenna) designed specifically for this application, and the board is fully calibrated.This ensures that you can support low-level IC calibration without having to write a large back-end – focus on your end application!.
  • This sensor cannot drive an LCD display on it own It will need a microcontroller, like ESP8266/ESP32 or Arduino Pro Mini / Pro Micro 3.3V The Microcontroller will control the sensor and control the display as well..
  • What you will get is : 1 X GY-AS3935 Lightning Sensor.
Check Stock

7Pcs ATTINY88 Microcontroller Development Board 16Mhz I2C and SPI 26-PWM Digispark ATTINY85 Nano V3.0 Extended Module

  • ATTINY88 micro development board based microcontroller development board similar to the board line, only cheaper, smaller, and a bit less powerful..
  • With the ability to use the familiar IDE the MH-ET LIVE Tiny88(16.0Mhz) is a great board to jump into electronics, or perfect for when an other board is too big or too much..
  • ATTINY88 micro development board has 26 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).
  • ATTINY88 micro development board support for the IDE 1.0+ (OSX/Win/Linux).
  • The MH-ET LIVE Tiny88(16.0Mhz) is fully assembled except for the headersincluded and easy to solder them by yourself..
Check Stock