Top Non contact Thermocouple

K Type Thermocouple Temperature Thermocouple Sensor Temperature Detector Temperature Gauge with M4 Thread for 3D Printer Temperature Sensor

  • Type K (chromel–alumel) is the most common general-purpose thermocouple with a sensitivity of approximately 41 µV/°C.[10] It is inexpensive, and a wide variety of probes are available in its −200 °C to +1350 °C (−330 °F to +2460 °F) range. Type K was specified at a time when metallurgy was less advanced than it is today, and consequently characteristics may vary considerably between samples. One of the constituent metals, nickel, is magnetic.
  • a characteristic of thermocouples made with magnetic.
  • They operate very well in oxidizing atmospheres. If, however, a mostly reducing atmosphere (such as hydrogen with a small amount of oxygen) comes into contact with the wires, the chromium in the chromel alloy oxidizes. This reduces the emf output, and the thermocouple reads low. This phenomenon is known as green rot, due to the color of the affected alloy. Although not always distinctively green, the chromel wire will develop a mottled silvery skin and become magnetic. An easy way to check for t.
  • Hydrogen in the atmosphere is the usual cause of green rot. At high temperatures, it can diffuse through solid metals or an intact metal thermowell. Even a sheath of magnesium oxide insulating the thermocouple will not keep the hydrogen out..
Check Stock

DRELD Low Pressure LPG Propane Gas Fireplace Fire Pit Flame Failure Safety Control Valve Kit with 5/8” -18UNF Inlet Outlet Thermocouple Knob Switch, Fits for Gas Grill, Heater, Fire Pit

  • SIZE: 750 mm thermocouple with M8*1 threaded head. Bakelite knob OD 38mm, D shaft 6.1mm..
  • APPLICATION: The kit is suitable for low pressure repair control system for Gas Grill, Heater, Fire Pit, & Fireplace..
  • MATERIAL: The fire pit gas control valve kit is made of brass and plastic for durable use. Not OEM but fits OEM Standards..
  • HOW TO USE: Fix the valve on a plate or board of your grill or fire pit by the head screw and flange. Connect your inlet and outlet hose on inlet and outlet side. Fix the thermocouple nut M8 on the valve end tightly. Connect thermocouple and end thread well. Open gas by correct size knob and push your valve around 5-10s till the thermocouple head is heated enough. Release your hand and it works properly. If the gas valve shut off again when you release hand, then please check..
  • AFTER SALES SERVICE: The Propane Fire Pit Kit Replacement Part completed with a One-year Warranty. Should be there any question, please feel free to contact us..
Check Stock

Thermco ACC310DLSDIG Laboratory Long Stem Digital Thermometer, 12\ Stem Length, -50 to 300°C Range, +/-1.0°C Accuracy

  • High Temperature K-type Thermocouple Thermometer Set with Stainless Steel Probe.
  • K-type thermocouple wire with Standard Accuracy: +/- 2.2 °C or +/- .75%.
  • 5 ft (155 cm) long thermocouple cable with braided stainless steel cover, mini thermocouple plug made from chromel / alumel.
  • Temperature measurement range: -328 to 932 °F (-200 to 500 °C), short term 1472 °F (800 °C).
  • Grounded K-type Thermocouple junction for fast measurements, 1x 9V battery included.
Check Stock

Instrukart Dry Block High Temperature Calibrator AI-DBC 650 for Calibration Labs Pharmaceutical divisions Thermal Plants divisions Along with Calibration Certificate

  • Accuracy: ±0.6°C, Bath Stability: ±0.5°C.
  • Measuring Functions: J Type Thermocouple, K Type Thermocouple, T Type Thermocouple, R Type Thermocouple, S Type Thermocouple, N Type Thermocouple, MA, MV, Volts, Ohms, RTD (Pt 100).
  • Temperature Steps: 50°C, 150°C, 300°C, 450°C, 600°C.
  • Switch Test: Continuity check with OPEN / CLOSE indication.
  • Transmitter Supply: 24V DC ± 10% (Loop Powered).
  • Power Supply: 230V AC ± 5% / 50Hz, 500 W for 350UTC.
  • Supply Scope: Instrument, Power Cable, Carrying Case, Test Lead(2 & 3 Wire), Insertion Tube, Insertion Tool,Spare Fuses: 6A x 2nos User Manual, Calibration Certificate.
Check Stock

3\ Outside Air Kit for Pellet Stoves with 3\ Air Intake Pipe Including Harman Stoves 3\ X 10'

  • QuadraFire Thermocouple 800, 1000, 1100i, 1200, 1200i Pellet Stoves 812-0210.
  • Top Quality Aftermarket Replacement Part.
  • The Thermocouple is the device that monitors the fire after start-up. Once it reaches temp the thermocouple allows the stove to start feeding on it's own in normal operation mode. If your stove goes out after the initial start-up cycle, more than likely the thermocouple needs to be replaced..
  • Designed Specifically for the above mentioned models.
Check Stock

Emerson H06F 36 Universal Junction Block Thermocouple 36 inch

  • 36 inch junction block thermocouple with energy cut-off.
  • Stainless steel element construction for prolonged thermocouple life.
  • Standard coaxial thermocouple 11/32 inch double lead thread.
  • Universal adapter fittings included with each kit for replacing thermocouple in most types of pilot burners.
  • Works for both LP and natural gas applications.
Check Stock

Fluke 568 Dual Infrared Thermometer, -40 to +1472 Degree F Range, Contact/Non Contact

  • Dual infrared and thermocouple thermometer for noncontact or contact temperature measurement in electrical maintenance and monitoring industrial and manufacturing processes.
  • Measures temperature with the infrared sensor from -40 to +800 degrees C (-40 to +1472 degrees F) with an accuracy of + or - 1 degree C (+ or - 2 degrees F).
  • Measures temperature with the included Type K bead thermocouple from -40 to +260 degrees C (-40 to +500 degrees F).
  • 50:1 infrared distance-to-spot ratio with laser sighting for pinpointing the measurement area.
  • Stores up to 99 points of data for analysis and monitoring on a computer.
Check Stock

FLUKE FLUKE-62 MAX+ INFRARED THERMOMETER, -30C to +650C / -22F to +1202F

  • Dual infrared and thermocouple thermometer for noncontact or contact temperature measurement in electrical maintenance and monitoring industrial and manufacturing processes.
  • Measures temperature with the infrared sensor from -40 to +800 degrees C (-40 to +1472 degrees F) with an accuracy of + or - 1 degree C (+ or - 2 degrees F).
  • Measures temperature with the included Type K bead thermocouple from -40 to +260 degrees C (-40 to +500 degrees F).
  • 50:1 infrared distance-to-spot ratio with laser sighting for pinpointing the measurement area.
  • Stores up to 99 points of data for analysis and monitoring on a computer.
Check Stock

2M K-Type Temperature Sensor Mini-Connector Probe Sensor Temperature Sensors Measure Range -40 to 400 Degrees Celsius (-104 to 752 Degrees Fahrenheit) for Thermocouple Sensor and Meter (5)

  • Quality material: the 2 m k-type temperature sensor is made of reliable material, it is anti-corrosion, waterproof and oil-proof and can withstand 400 degrees Celsius.
  • The temperature probe can provide you with long-term service so you can use it with confidence.
  • Sensitive response: the thermal response time of this temperature control probe is 0.1 seconds, such a sensitive response will improve your work efficiency and bring you a nice using experience.
  • Liquid measurement: the difference between this thermocouple probe and other common thermocouples is that it is waterproof and can be applied in some projects that come into contact with water, the feature of this mini-connector probe sensor will make your work much smoother.
  • Space temperature: the appearance of the k-type probe is made of teflon material, and the quality is reliable, and it has the feature of non-combustibility, insulation, high and low temperature resistance.
  • Wide range of applications: this grounded thermocouple can be applied to measure the surface temperature of molds, casting molds, flat glassware, aluminum manufacturing, bearings and other solid surfaces, etc..
Check Stock

Vampires & Informers Liondub & Tester s BK Jungle Mix

  • True-RMS Multi -Function Clampmeter: easy to use and operate.
  • can accurately measure AC current, test AC and DC voltage, Low impedance, serve as....
  • NCV or Non Contact Voltage Detector: it can detect conductor with a voltage higher than 90V AC without touching any wires.
  • LCD display with backlight, data hold function, low battery detector, overload protection, auto power off after 15 minutes, etc.
  • Test probes (2 types), thermocouple, test clips, dupont wire probes, crocodile clips, mini crocodile cable, mini wire stripper tool, mini....
  • Satisfaction guarantee: 30-day manufacturer guarantee and lifetime customer support.
Check Stock

GBC Document Camera, Discovery 3000 (DCV10004)

  • pyrometer Temperature range: -50°C to 1300°C ( -58°F to 2372°F) and Overload display alert when input exceeds measurement range pyrometer. Thermocouple Temperature range: -50°C to 1000°C ( -58°F to 1832°F).
  • Designed for use with K-type thermocouples and Selection between Celsius and Fahrenheit.
  • Decimal or round number display selectable (decimal range is -58.0F to999.9F and round number range is -58F to 2372F).
  • Includes 2 Thermocouples ( One 3" K type temperature probe (-58 – 752 °F) and one Kiln Heavy duty K type Thermocouple ( -58°F to 1832°F) and Digital Pyrometer, 9V battery and Manual.
  • Thermocouple Measurement range: 32 - 1832 °F (0 - 1000 °C) Thermocouple Type: K Type Cable length : 3 ft Sensing tip length: 6" (150mm) Stainless Steel Sensing tip diameter: 0.19" (5mm) Thread width : 5/16" (M8) Internal Insulation: Fiber Glass External shielding: Metal Shield (Stainless steel braided).
Check Stock

Coolrunner Gas Patio Heater Repair Replacement Parts Outdoor Heaters Safety Kits Thermocouple (M8 x1) and FD4 Dump Switch for Propane Gas Patio Heater

  • Well Made & More Safe: The thermocouple is made of brass and red copper and the anti-tilt switch, made of ABS, which will automatically stop heating when the gas heater is tilted..
  • Wide Compatibility: The patio heater thermocouple replacement is suitable for most of propane heater, patio heater and other gas heaters with thermoelectric safety..
  • Dimension: The total length of thermocouple is 350mm, thermocouple probe is M6*0.75 and threaded end is M8*1, please measure your original parts before ordering. Weak current FD4 dump switch is for gas R≤10 mΩ..
  • Easy to install: It is easy to replace just follow the way you remove the defective part. Notice: Keep the thermocoupler probe about 5mm from the burner hole..
  • Great Value for Money: If the thermocouple or dump switch of your gas heater is broken, you just need to change the replacement that will save $200 for you..
Check Stock