Top Ntc Temperature Sensor

XINGYHENG STC-1000 DC 12V 10A Microcomputer Digital Display Temperature Controller Thermostat Control Switch 2 Relay Output and NTC 10K Thermistor Sensors Digital Temperature Probe (12V)

  • Super material: STC-1000 intelligent thermostat is an independent product, ABS flame retardant shell, a variety of fields perfect use, convenient operation and practical Settings, is your side temperature control housekeeper..
  • Package including: 1 Pack of STC-1000 intelligent thermosta module, which is equipped with 1pcs NTC 10K temperature probe. The NTC probe is waterproof and allows to control the temperature even of fluids, allowing the controlled heated or cooling..
  • STC-1000 Digital Thermostat specification: Temperature control range: -50-99°C. Control accuracy of 0.1 degrees Celsius. Control temperature by setting the temperature setting value and the difference value.
  • Temperature calibration. Easy operation, to set start temperature, stop temperature, corrected temperature correction, delay start..
  • High Power High Efficiency: Two Work Mode: Heating ( start temperature is less than stop temperature), Cooling ( start temperature is above than stop temperature) It is precise and reliable with good long-term stability. Refrigerating contro,l output delay protection.Alarm when temperature exceeds temperature limit or when sensor error..
  • A wide range of applications: temperature controller is equipped with over 40’’ inch waterproof probe can be us....
Check Stock

Resideo WT8840B1000 Water Heater Gas Control Valve NAT 160 Degree F 1 Cavity

  • Temperature ratings: ambient-- 0 c to 60 c. Inlet/Outlet Size (in.) - 1/2 inch. NPT x 1/2 inch. Inverted Flare. Capacity - Min. 30 ft3/hr, Max. 75ft3/hr.
  • Pressure regulator setting (psi): 5.0 in. Wc.
  • An included integrated NTC temperature sensor reads water temperature within the appliance up to 221 F (105 C).
Check Stock

uxcell NTC Thermistors Resistor MF52-103/3435 10K Ohm Inrush Current Limiter Temperature Sensor Pack of 40

  • 【Quality】 - Directly Inserted Negative Temperature NTC Thermistors have large material constant, large B value, with small residual resistance.Thermal shock resistance, with wide range of operating temperature..
  • 【Feature】 - The NTC thermistors are reliable and stable, with wide range of over-current control..
  • 【Advantage】 - With small size and large power, NTC thermistors have strong capacity to inhibit surge current..
  • 【Application】 - NTC Thermistor is widely used for controlling the inrush current of motor, heaters, bulb voltage stabilizer, electronic energy-saving lamp, etc..
Check Stock

KETOTEK KT8230 Digital Temperature Controller Thermostat Regulator 120VAC 30A Fahrenheit -22~572℉ Heating Cooling for Incubator Brooder Refrigerator Fermenter Greenhouse Reptile

  • 【Wide temperature range.】The range for KT8230 is -22~572℉, This is a relay temperature controller, There is no voltage output directly, you need to connect additional power supply for the load, then it can be set by differential (1~80℉) to turn on/off the load, it is like a switch..
  • 【Output is 30A relay, more accurate.】The temperature controller 120V can be used for big power equipment, like incubator, brooder, refrigerator,Fermenter,Greenhouse,etc. 1°F accuracy to keep the temperature in desired range..
  • 【Support delay start function and temperature correction.】The cooler and heater will delay to work if you set the delay time(PL: 0~7min) not 0, You can set depend on what you need. -30.0°F～30.0°F calibrate the temperature when there is error..
  • 【Safe protection.】Temperature Regulator will alarm when it exceed temperature limit or sensor error, alert you when something wrong happened. You can also set the low(LS) and high temperature limit(HS) to change the temperature range, LS < Setting Temperature < HS..
  • 【Simple operation.】 All parameters setting can be saved after restart, you don’t need to set the thermostat regulator when power off, or restart it from vacation. 2m NTC sensor allows more possibility for home.
Check Stock

uxcell 20PCS NTC Thermistors Resistors MF58 3950B 10K Ohm Glass Sealed Temperature Sensors

  • Made of high-quality materials and has a long service life..
  • Small size, fast reflection speed, stable operation for a long time, good consistency..
  • NTC (negative temperature coefficient) thermistor, its resistance decreases with increasing temperature. High resistance and B value accuracy.
  • Widely used in air conditioning equipment, heating equipment, electronic thermometers, liquid level sensors, etc..
  • Material: Oxide film. Temperature coefficient: NTC. Rated power: 0.25w. Package includes: 20 x NTC thermistor..
Check Stock

UNI-T Bluetooth Wind Speed Meter UT363BT Handheld Mini Digital Anemometer with Thermometer and Max/Min for Weather Data Collection and Outdoors Sports Windsurfing Sailing with Backlight LCD Display

  • Bluetooth function is added for data transfer and analysis on mobile App, iENV, which can be downloaded from App Store..
  • It is widely used in mining, electric, iron and steel, petrochemical, energy saving,navigation, fan manufacturing, exhaust ventilation, sporting and....
  • Magnetic induction type wind speed sensor and NTC negative temperature coefficient sensor..
  • 12 Winds Article dynamically indicating eliminates the trouble of complicated conversion..
  • Dual display of wind speed and temperature..
Check Stock

GOQOTOMO Smart Temperature Controller Thermostat Heating and Cooling Mode for Homebrew Fermenter Greenhouse Terrarium 100-240VAC NTC Sensor Improved Version

  • [Smart Display] Everything clearly displayed in one color screen, including measured temperature, heating/cooling temperature, high/low temperature alarm and compressor delay..
  • [User Friendly] It is the easiest temperature controller on the market that you are able to operate without user manual. Setup and display is intuitive..
  • [Detachable Probe] The probe is easy detachable from Type-C port. Probe replaceable once it breakdown..
  • [Dual Output] Two independently controlled relays allow to control refrigeration and heating equipment at the same time..
  • [Reliable Accuracy Reading] Enhanced NTC sensor offer accuracy measuring and reading..
Check Stock

FR Limoss Compatible MC-140 Replacement Electric Recliner Lift Chair Power Supply with Battery Back up

  • Safety: NTC-temperature-sensor, primary fuse, overload protection.
  • Intermittent mode with 10% duty cycle with max. continuous use of 2 min..
Check Stock

KETOTEK Digital Thermostat Plug Outlet Timer Day Night Temperatue Controller Outlet Thermostat 120V for Reptile Terrarium Greenhouse Heating/Cooling Control 110v

  • 【Relay output, easy to use】 Plug-and-play design, 3 modes available to be chosen from: M1 temperature control mode, M2 temperature control with timer mode and M3 timer mode. Power supply: 100~250V AC 50/60Hz.
  • Output: Max 15A/120V. Temperature control range:-40℃~120℃/-40℉~248℉..
  • 【M2 mode-Day/night temperature control function】 This temperature controller outlet plug can be set different temperatures with its function of dual time cycle setting during 24 hours according to the day and night. For example, during 8:00~18:00, control the temperature between 23℃~25℃.
  • during 18:00~8:00 the next morning, control temperature between 17℃~19℃, then cycle every day..
  • 【M1 mode-Temperature control function without timer】 If you only need to control temperature simply regardless of time period, you can choose M1 mode: temperature control mode. Set start temperature and stop temperature, it will control the heater or cooler to work as programmed. (start temperature 003e stop temperature, cooling.
  • start temperature 003c stop temperature, heating)..
  • 【M3 mode-Timer function with 2 time period during 24 hours】 This day/night temperature controller plug has timer function with dual time cycle setting during 24 hours. For example, set Time 1 O....
Check Stock

24V 40W 620 Ceramic Cartridge Heater with 3950 100K NTC Thermistor with 1 Meter Wiring for RepRap 3D Printer Heatbed Hot End

  • 1 Meter long wire with high temperature PTFE insulated wiring and female pin head, 1.25mmx2.0mm glass bead.
  • Temperature sensor 100KΩ accuracy of ± 1%.
  • 24V 40W 620 Ceramic Cartridge Heater and NTC Thermistor 100K 3950 for 3D Printer Creality CR-10S Pro, CR-X,Ender 3,Ender 3 Pro, Ender 3 V2,Prusa....
Check Stock

3PCS HT-NTC100K Thermistor Sensor for Creality Ender 3 v2 Upgrade 3x15mm 3950 Compatible with E 3D V6 Volcano PT100 Ender-3-5 Pro CR10 3D Printer

  • 【Ender 3 Thermistor, Upgrade HT-NTC100K Thermistor】Cartridge temperature sensor. Metal head diameter: 3mm, head length: 15mm,cable wire length: 1 meter,connector: XH2.54 2PIN, （Suitable for heating blocks with holes of 3mm*15mm-3mm*20mm）.
  • 【Widly Compatibility】Product recommended operating temperature -50 °C ~ +280 °C, can replace the cartridge K-type thermocouple temperature sensor. Suitable to print multi kinds of filament.Compatible with the heatblocks with 3mm hole,such as: V6 Volcano PT100 type heated block,CR10 plated copper high temperature heating block,etc.
  • 【High Stability and Accuracy 】Encapsulated in copper case,copper material has better thermal conductivity than stainless steel and improves accuracy.Secured with high temperature adhesive,high stability, no falling off.The internal temperature package to ensure the maximum service life with precision temperature measurement..
  • 【Long Service Life】Compared with other products of the same type that are insulated with ordinary heat shrinkable tubes, this product uses glass fiber with a temperature resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temperature work. Thereby increasing the service life..
Check Stock

Testo 104 - Waterproof Folding Food Thermometer (Part Number 0563 0104)

  • Features: Ideal for applications in the food sector | Two purposes: Infrared and penetration thermometer | High-quality including robust folding joint for tough working use | 2-point laser with 10:1 optics shows the exact measurement area..
  • Temperature - NTC Range: -50°C to +250°C, Accuracy: ±1.0°C for (-50°C to -30.1°C), ±0.5°C for (-30°C to +99.9°C), ±1 % of mv for (+100°C to +250°C), Resolution: 0.1°C, Reaction time: t99 = 10 s | Operating Temperature: -20°C to +60°C.
  • Display lighting: illuminated | Housing: ABS / TPE / PC, diecast zinc, stainless steel.
  • Protection class: IP65 | Diameter probe shaft tip: 2.3 mm.
  • Futher features: Auto hold, hold, min./max. |.
  • Diameter probe shaft: 3 mm | HACCP-compliant | Battery type: 2 AAA micro batteries.
  • Accessories: Testo 104 food thermometer with folding temperature sensor, user guide, calibration protocol, adhesive color strips, batteries. | Applications: Food transport trucks, refrigerators, Food Industries, hotels & restaurants, etc..
Check Stock