Top Pcb Board Assemble

HPYNPES DIY Practical Soldering Practice Kit Practice Learning Electronics Training Board

  • Product introduction: Shake the lucky turntable by NE555 and CD4017 chips combined with LED random output function. The control terminals are button control and vibration switch control. You only need to press the button or shake it, the LED will start to rotate, and the After a while it stops randomly, leaving only one LED light..
  • Designed for Beginners：Special design for electronics starter to learn to solder electronics components. Soldering project kit will improve your electronic knowledge and soldering skills in practice.
  • Easy to Assemble： Electronic DIY kits uses safety materials, effectively avoid corrosion and wear out. Components’ names have been marked on the PCB board and the circuit design is simple. Even beginners can easily solder successfully.
  • Warm Reminder ：DIY electronic components kit requires buyer to assemble and welding, If you don't have any soldering experience, please read the soldering instructions and use soldering tools carefully to avoid safety problem.
Check Stock

4X Prototype PCB for Arduino Mega 2560 R3 Shield Board DIY

  • Prototype PCB for Arduino Mega 2560 R3 Shield Board DIY..
  • PCB Dimension: 101.6mm x 53.34mm / 4" x 2.1".
  • PCB Thickness: 1.6mm / 0.063", Material: high quality FR-4 glass fiber PCB..
  • All holes are plated through. Top and bottom side are identical copper layers. Pads grid (pitch) 2.54mm / 0.1", hole diameter 0.9mm..
Check Stock

Strobe Receiver

  • Directly printing inductor traces on the PCB board greatly simplifies the difficulty of assembly..
  • The kit uses a band-pass filter, 3355 high-amplifier, NE602 mixing, MC1350 mid-amplifier solution, which can receive AM signals of 118-136MHz..
  • 12V power supply, 9.2 x 7.5cm PCB board size, which can be directly used in 97 x 40 x 75mm aluminum chassis.
  • The AGC circuit on the board ensures comfortable listening, while the squelch function avoids long-term noise..
  • It is specially used to receive the call between the aircraft and the tower. With the antenna with good performance (VHF band Yagi antenna), the open area can receive various types of aircraft and tower calls within about 190Km. Please pay attention to your favorite friends..
Check Stock

USB Female Type-B Port 4-Pin Right Angle PCB DIP Jack Socket-White 10 Pack by MUZHI

  • As the carrier of the IC chip, the IC connector can replace the chip and PCB board for repeated welding and disassembly without damaging the chip, achieving the effect of saving IC cost and time.
  • When installing,first solder the chip to the IC connector, and then solder the IC connector to the PCB board.
  • when you need to install or replace the chip, directly remove the connection between the IC connector and the PCB board, without changing the chip and connector Connection..
  • Advantages-IC connector has strong vibration and heat resistance, can withstand repeated welding and disassembly, convenient installation, and easy to use.
  • Noted - The spacing and line spacing of the connector holes must be the same as the spacing and line spacing of the chip pins.
Check Stock

WiFi Wireless Card Module PCB Board for Nintendo DSi NDSI Replacement DWM-W024

  • Wifi Wireless Card Module PCB Board for Nintendo Wii U..
  • Please check description , the images and package carefully ..
Check Stock

Bluetooth Amplifier Board 25W+25W HF63 Dual Channel Audio Amplifier DC 10-25V Digital Amplifier Module with TDA7492P Chip

  • High Quality : The amplifier board adopts TDA7492P power amplifier chip, high quality electronic components and military grade PCB board, durable in use..
  • 2 Channel : This board is designed with dual channel output, 25W left channel and 25W right channel, high transmission rate and good sound quality..
  • Bluetooth Connection : The amplifier board is designed with Bluetooth V2.1 module and power supply reverse connection protection, convenient and safe to use..
  • Application : This digital amplifier board is suitable for upgrading and refitting the idle sound box and DIY production. It is suitable for speaker of 4Ω, 6Ω, 8Ω, 16Ω (8Ω is the best)..
Check Stock

Keyboard Switch Sound Dampeners Sheet Silencer Foam Silencer Pad for Mechanical Keyboard（96 Layout）

  • 【Product Function】 Using this product can eliminate the cavity sound of the keyboard, increase the thickness of the tone, and reduce the resonance....
  • 【Easy Installation 】Install directly between PCB and steel plate without adhesive. And will not affect the light position of the keyboard..
  • 【Material】Made of soft sponge material, with high-efficiency noise reduction effect, and will not damage your PCB board..
  • 【3mm Thickness】Because the distance between the PCB and the positioning board is between 3mm and 3.5mm, this 3mm silencer pad is the best choice....
  • 【Warm Tips】This silencer pad is drawn based on the actual measurement of the keyboard. It is not manufactured by the original factory and cannot....
Check Stock

uxcell 17pcs DIP IC Chip Socket Adaptor Round 28 Pin 2.54mm Pitch Dual Row 15.24mm Row Pitch

  • Row to Row Distance(Approx):15.24mm/ 0.6".
  • As the carrier of the IC chip, the IC connector can replace the chip and PCB board for repeated welding and disassembly without damaging the chip, achieving the effect of saving IC cost and time.
  • When installing,first solder the chip to the IC connector, and then solder the IC connector to the PCB board.
  • when you need to install or replace the chip, directly remove the connection between the IC connector and the PCB board, without changing the chip and connector Connection..
  • Advantages-IC connector has strong vibration and heat resistance, can withstand repeated welding and disassembly, convenient installation, and easy to use.
  • Noted - The spacing and line spacing of the connector holes must be the same as the spacing and line spacing of the chip pins.
Check Stock

uxcell 20pcs DIP IC Chip Socket Adaptor Solder Type 2.54mm Pitch Dual Row 8 Flat Pin 7.6mm Row Pitch

  • As the carrier of the IC chip, the IC connector can replace the chip and PCB board for repeated welding and disassembly without damaging the chip, achieving the effect of saving IC cost and time.
  • When installing,first solder the chip to the IC connector, and then solder the IC connector to the PCB board.
  • when you need to install or replace the chip, directly remove the connection between the IC connector and the PCB board, without changing the chip and connector Connection..
  • Advantages-IC connector has strong vibration and heat resistance, can withstand repeated welding and disassembly, convenient installation, and easy to use.
  • Noted - The spacing and line spacing of the connector holes must be the same as the spacing and line spacing of the chip pins.
Check Stock

Latitool F50 Laser Engraver, 50W Laser Engraving Cutting Machine, 5.5-7.5W Laser Power, DIY Engraver Tool for Metal/Glass Etching Kit/Wood Carving, Engraving Accuracy 0.01mm, Area(15.74\x16.14\)

  • ...ng area, can be enjoy to watching your artworks producing..
  • Solid & Easy Installation Structure Design: Industrial grade steel structure design makes the laser cutter and engraver machine more reliable and improves engraving accuracy. The entire engraver tool adopts a modular design, which is convenient for users to assemble, repair, replace and update laser engraving machine parts. And the assembly can generally be completed within 10-20 minutes..
  • Large carving Area: 400*410mm (15*16 inch) Large engraving range to meet various DIY needs. Unleash your creativity on over one hundred materials including black metal and wood, acrylic, paper, glass, bamboo, leather PCB board, aluminum oxide, etc..
Check Stock

PCB Drill Bits Set, Micro Drill Bits Set, 50pcs PCB Drill Bit Set Spiral Flute Carbide 0.3mm-1.2mm Drill Bits for Dremel Print Circuit Board Jewelry CNC Engraving (5PCS Each) by BOOTOP

  • This PCB Drill Bit Set contains 10 different size drill bits diameter: 0.3mm, 0.4mm, 0.5mm, 0.6 mm, 0.7 mm, 0.8 mm, 0.9 mm, 1.0 mm, 1.1mm, 1.2mm. And each size have 5 pcs. Varies sizes to meet different needs..
  • This micro drill bits are designed to drill and engrave on print circuit board and other precise work. The PCB Drill Bits are made of high quality tungsten steel, highly wear resistance, high hardness, bending strength, anti-impairment, highly working efficiency. Seismic design on the blade edge enables it to stay stable during engraving..
  • PCB Drill Bits Set are great for punching at printed circuit boards, 3D Printer Nozzle Cleaning, CNC engraving plexiglass, Amber beeswax, bakelite, jewelery, metal plastic and other precision drilling.
  • cutting and engraving and worked on Acrylic, PVC, Nylon, Resin, Fiberglass,etc..
  • PCB Drill Bit With sharp cutting edge, milling groove and clean surface, these sets of tool work quickly and cleanly, no glitches or scrap left. Package with high quality plastic box, easy carry and better protection keeps the blade tip goods in the delivery from being damaged..
  • 180 Days warranty. If you are not satisfied with our products,feel free to contact us for a replacement or refund. The PCB Drill Bits may also know as micro d....
Check Stock

ODOMY 57pcs Pin Vise Hand Drill Bits Mini Hand Drill Rotary Tool,46pcs 0.3-3.0mm Micro Twist Drill Bits and 10pcs PCB Mini Drill Bits for Resin Plastic Wood Jewelry Making

  • Practical and Portable: The hand-held drill is easy to carry or store in a toolbox or pocket, making your daily work more convenient, suitable for electronic assembly, tools, model making, winding, home decoration, etc..
  • Pin Vise Hand Drill: Aluminum alloy, sturdy and durable, its tail can be rotated, sturdy and easy to operate, Ideal for making pilot holes when fixing small item that you can’t hold eg plastic sleepers on the track..
  • You Will Receive:A total of 57 pieces of electric hand drill set for you to do hand-carving DIY work, Twist drill bit: 0.3-3mm, PCB micro drill: 0.1mm-1mm, Vise: 3.5*0.6inch..
  • PCB micro drill: PCB micro drill is made of tungsten carbide, suitable for processing PCB, ordinary FR-4, CEM-3 board, SMT, CNC, mold, plastic, circuit board, carbon fiber, composite board, etc..
  • Micro twist drill: The micro drill is light in weight and compact in size. It does not take up extra space. It is used to process wood, plastic, rubber, PVC, walnut, model, bone, angle steel, amber, olive, fiberglass, and other materials..
Check Stock