Top Picatinny Rings On Weaver Base

Monstrum Precision Picatinny Scope Rings | 1 inch Diameter | 1.20 inch Height

  • 1.20 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
  • 1 inch diameter rings for mounting standard 1 inch rifle scope tubes.
  • Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
  • Available in four heights to match your needs: 0.80 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Athlon Optics Precision 34mm MSR Ring, Black (701007)

  • Double 1'' scope ring mount for Picatinny/ Weaver Rail (21mm)..
  • Design in hollowed-out configuration between the ring and the bottom of the base, to release heavy duty when clamping your scope..
  • Built-in tape inside per rings to prevent from marring the scope, also prevent sliding and holding postion accurately..
  • The ring is for most scopes which are in 1''/ 25.4mm scope tube. High profile, 0.98'' gap from base of mount to bottom of rings. ( Item height: 2.1'').
  • With only 1 rail clamp screw and 1 scope clamp screw per side, just twist off the nut and mount the base on the 20mm rail easily..
Check Stock

Monstrum Precision Picatinny Scope Rings | 30 mm Diameter | 0.85 inch Height - Low

  • 0.85 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
  • 30 mm diameter rings for mounting standard 30 mm rifle scope tubes.
  • Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
  • Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Higoo 2PCS 11mm Dovetail to 20mm Picatinny/Weaver Low Pro Snap-in Rail Adaptor

  • Top slot with spring tension retraction/expansion design to snap into Picatinny/Weaver base.
  • Extremely low profile and lightweight,Removable Stop Pin for Extra Secure Installation.
  • Top Slot with Spring Tension Retraction/Expansion Design to Snap into Picatinny/Weaver Base.
  • Type: Picatinny/Weaver Contains Right Angle Wrench*1.
Check Stock

Weaver Thumbnut Spr 1\ Mount

  • [Picatinny Riser Mount] This riser mount base fits on standard Picatinny/Weaver rail..
  • [Unique Adapter] The unique design makes the riser mount look symmetrical and beautiful,and can be firmly fixed on the track without shaking or falling off..
  • [5 Picatinny Slots] With 5 Picatinny slots, 2 inches long / 0.75 inches high, suitable for equipment with Picatinny or Weaver adapter. Such as: reflex sight, red dot sight..
  • [Material] Made of high-quality aircraft aluminum, resistant to high and low temperature, anti-corrosion, anti-rust, light weight, strong and durable..
  • [Size & Weight] Height: 0.75 inches, upper width: 0.82 inches, lower width: 1.2 inches, length 2 inches, weight: 1.5 oz, lightweight and mini..
Check Stock

Monstrum Precision V2 Picatinny Scope Rings with Integrated Level Bubble | 30 mm Diameter | Low Profile

  • Monstrum Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
  • 30 mm diameter rings for mounting standard 30 mm rifle scope tubes.
  • Picatinny mount base mechanism comes equipped with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil | Not compatible with Weaver mounts.
  • Scope rings come with an integrated level bubble mechanism for quickly checking if your rifle is lined up square with your target.
  • Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Monstrum Precision V2 Picatinny Scope Rings with Integrated Level Bubble | 30 mm Diameter | High Profile

  • Monstrum Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
  • 30 mm diameter rings for mounting standard 30 mm rifle scope tubes.
  • Picatinny mount base mechanism comes equipped with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil | Not compatible with Weaver mounts.
  • Scope rings come with an integrated level bubble mechanism for quickly checking if your rifle is lined up square with your target.
  • Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Offset Rail Mounts LONSEL 4 Slots Aluminum 45 Degree Offset Angle Picatinny Weaver Rail Mount for Flashlight Laser Optic Sight - 3 Pack 4 Slot - 3 PCS

  • ❖【45 Degree Offset Picatinny Rail Mount】Super Lightweight Rails, Low Profile Design. Allows the Attachment of Lasers, Flashlights, Red Dot....
  • ❖【Fits 21mm Picatinny Weaver Rail System】The Rail Mount Base Fits On Standard 21mm Picatinny or Weaver Style Rail, Ensure Mounting Tactical....
  • ❖【Offset 4 Slots Picatinny Rails】With 4 Slots Picatinny Rail, Allowing You Quickly Add On Any Standard Picatinny or Weaver Accessories, Such As....
  • ❖【Solid & Durable】Precision Machining of High Grade 6061 Aluminum Alloy + High Tensile Steel In Black Matte Anodizing Finish, Durable &....
  • ❖【Quick Release & Easy To Install】Simple Side Screw Structure, It Secures and Detaches Quickly with Single Thumb Tightening, Easy and Quick To....
Check Stock

Vortex Optics Hunter 30mm Riflescope Rings - Medium Height (0.94 inches)

  • These Vortex Hunter Rings position the center of the riflescope tube at a height of 0.94 inches (24.0 mm) from the base.
  • Mounting to a Picatinny or Weaver type rail, the standard, 2-screw Hunter rings are a nice match for general hunting setups.
  • Made from aircraft-grade 6061-T6 aluminum for optimum strength.
Check Stock

Vortex Optics Hunter 1-inch Riflescope Rings - Low Height (0.63 in)

  • These Vortex Hunter Rings position the center of the riflescope tube at a height of 0.63 inches (16.0 mm) from the base..
  • Mounting to a Picatinny or Weaver type rail, the standard, 2-screw Hunter rings are a nice match for general hunting setups..
  • Made from aircraft-grade 6061-T6 aluminum for optimum strength..
Check Stock

Vortex Optics Hunter 30mm Riflescope Rings - High Height (1.22 in)

  • These Vortex Hunter Rings position the center of the riflescope tube at a height of 1.22 inches (31.0 mm) from the base..
  • Mounting to a Picatinny or Weaver type rail, the standard, 2-screw Hunter rings are a nice match for general hunting setups..
  • Made from aircraft-grade 6061-T6 aluminum for optimum strength.
Check Stock

Monstrum Precision V2 Picatinny Scope Rings | 34 mm Diameter | 1.40 inch Height

  • 1.35 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • 34 mm diameter rings for mounting standard 34 mm rifle scope tubes.
  • Picatinny mount base mechanism comes equipped with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil | Not compatible with Weaver mounts.
  • Uses hardened steel Torx mounting hardware to prevent stripping of the bolts.
  • Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock