Top Pinch Weld Jacks

Reinforced Double Wheel Trailer Jack Caster with Pin (2000 Pound Rated)

  • 2000 Pound Rated Double Caster Wheel with Under Carriage Weld Supports.
  • Adjustable Side Bolt for Tightening Eliminates Rattle and Play.
  • Swivel Caster Wheel Fits All Standard Jacks.
Check Stock

Poweka 13FT Butyl Rubber Sealant Tape for Car Auto Headlamps Window Door Windshield,4M Black Butyl Rope

  • Butyl Sealant Main Application: Butyl rubber tape is suitable for the shock-absorbing paste of windshield, door waterproof film,decorative parts,car....
  • Excellent Sealing：Our Butyl rubber sealant features excellent sealing adhesion,butyl tape can be sticky to any type of metal,....
  • Easy To Use: Simply release the butyl sealant from paper and press it sufficiently around the pinch weld.And after removing headlamp cover, the weld....
  • Black Butyl Tape: Rubber Sealant is a non-drying,non-hardening synthetic rubber based butyl rubber sealant. It will remain permanently sealing and....
  • Butyl Windshield Sealant Size: Butyl sealant Diameter: 7-10 mm, Length: about 4 meters. It is long enough for re-sealing about 2 or 4 headlight....
Check Stock

DIY Car Universal X-Slot Jack Pad Rubber Frame Rail Adapter Protector Pinch Weld Side Car Lifting Anti Slip Design Floor Support 10x4.7cm Trolley

  • Made of Durable rubber construction and cross slotted design, provides more cushion and crush resistance..
  • Jack pad is strong enough to support your lifting point and soft enough to prevent bending or fracture of clamping weld and frame longitudinal beam when jacking up your car..
  • Fits most Jacks and vehicles, please verify dimensions and ensure fitment to your vehicle..
  • There is a slotted crossline on the top of the car jack pad, which can align with the side clip weld and protect the side, so as to prevent the frame longitudinal beam from bending when lifting the vehicle with the jack..
  • Maximum load: 3 tons, Diameter:10cm/3.93in.Thickness:4.7cm/1.85in..
Check Stock

3M 08612 Window-Weld 3/8" x 15' Round Ribbon Sealer Kit

  • Controlled compressibility allows easy installation yet will not squeeze out or allow light to contact pinch weld. Sufficient material to replace one windshield or backlight..
Check Stock

Omega 47020 2000 lb HD 3 in 1 Car Dolly Set 1 Pack

  • Holds vehicles in 3 ways: 1) by the wheels, 2) by the pinch weld, 3) by the frame.
  • No tools required.Adapter secured with pins + Locking casters.
Check Stock

RetroRubber OEM Grade Butyl Headlight Sealant, Gray

  • ★Butyl Sealant Main Application: Butyl rubber tape is suitable for the shock-absorbing paste of windshield, door waterproof film,decorative parts,car lamp,bus body and frame,as well as the sealing of body seam and flange plate.
  • ★Excellent Sealing: Our Butyl rubber sealant features excellent sealing adhesion,butyl tape can be sticky to any type of metal, concrete,glass,plastics and porous surfaces,no worries for falling off. Easy installation and removal.
  • ★Easy To Use: Simply release the butyl sealant from paper and press it sufficiently around the pinch weld.And after removing headlamp cover, the weld areas should be dry,clean,free from dust,oil and grease.Butyl rope prevent leakage,corrosion,deformation,vibration, weather and aging. Non-toxic, tasteless, pollution-free, easy to use.
  • ★Black Butyl Tape: Rubber Sealant is a non-drying,non-hardening synthetic rubber based butyl rubber sealant. It will remain permanently sealing and waterproofing,high viscosity,elasticity and tightness.
  • ★Butyl Windshield Sealant Size: Butyl sealant Diameter: 9mm, Length: about 4 meters. It is long enough for re-sealing about 2 or 4 headlight assemblies, easy to cut to fit for your need.
Check Stock

2-Pack of Rubber Jack Pads (Slotted Pucks) - Universal, Standard-Size Adapter - Frame Rail Protector Puck / Pad Keeps Pinch Weld, Paint and Metal Safe - by Mission Automotive

  • Protects Your Vehicle And Your Jack -- Our jack pads sit on top of your jacks to provide protection and cushion when lifting your car, both to the sensitive areas of the vehicle itself as well as the jack that's doing the heavy lifting. No more damage to pinch welds, paint scratches or metal damage.
  • Made From High Quality Material, Built To Last -- Made from a blend of purpose-specific, highly durable rubber, our jack pads are built to hold up to the rigorous needs of mechanics and DIY enthusiasts, alike.
  • Fits An Array Of Jacks, Stands And Vehicles -- Our pucks are made to fit a wide array of jacks / jack stands and vehicles. Their universal size allows them to meet a wide-array of needs, though exact fit will vary.
  • Value Pack -- Our set includes two jack pads, providing the value you need to get the job done right - without sacrificing quality..
  • Dimensions -- Pad dimensions: 7.2 cm / 2.8 inches in diameter, 3.3cm / 1.3 inches tall. 2 per pack.
Check Stock

Toolly 16 Pack Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Butt Welding Clamps includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
  • Use the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
Check Stock

Fulton 500320 XP to F2 Adapter Kit for F2 Swivel Mount with 4' Frame

  • Fulton F2 Jack Adapter Plate allows you to upgrade from a Fulton Center-Bolt Swivel Mount Jack to an F2 Series Marine and Recreational Jack.
  • Fits Fulton's patented center-bolt design - used on XP10 and XP15 weld-on jacks.
  • Heavy-duty, cast aluminum mount is tapered, moving wheel closer to center line of trailer frame to optimize castering performance.
  • installs easily - no drilling or welding required.
  • All necessary mounting hardware and complete installation instructions included.
Check Stock

ABN Butt Welding Clamps - 8 Piece Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • [Perfectly Align Panels] Use the ABN Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • [Fits your Project] Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • [Easy to Use] Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 8 clamps for larger projects, then joint weld between them.
  • [Built to Last] Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
  • [Contents] Welding accessories set includes 8 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Check Stock

Pair of Trailer Stabilizer Jacks Telescoping RV Camper Accessories for Travel 450kg 1000 Lbs Capacity Each

  • Each trailer stabilizer jack: Extended height: 18".
  • Retracted (collapsed) height: 11-1/2", static load capacity: 1000 lbs, lift capacity: 650 lbs, which helps to keep your trailer level and stable..
  • Design：design of telescoping structure, strong and easy to bolt or weld, suitable for RV trailer camper stabilizing leveling.
  • Product surface: black environmentally friendly electrophoretic paint, not easy to rust.
  • Reminder: you will need to supply your own mounting hardware: four 3/8" bolts, but the mounting holes are pre drilled..
Check Stock

GripperX Headphone Plug Extraction Tool with Key Ring and Cleaning Brush - Remove Broken Headphone Plug from Headphone Jack of Mobile Devices

  • NO GUARANTEES: This tool comes with no guarantees implied or expressed and should be considered a single-use tool..
  • PURPOSE: GripperX is designed for the purpose of extracting a headphone plug that has broken apart, leaving the tip of the plug lodged inside the headphone jack of a mobile device..
  • HEADPHONE JACKS: Designed to be used on 3.5mm jacks found on phones, laptops and smaller devices..
  • HOW TO USE: Insert GripperX between headphone jack housing and broken plug. You may need to lightly tap it in. It should go in about the same length of the headphone plug. Pinch with fingers or pliers for better grip. With broken plug enclosed, pull to remove. Restore functionality to your device's headphone jack..
  • USE WITH CAUTION: Rotating or inserting too far may damage the device. The opening is sharp and may cause harm to your fingers. We recommend using gloves and pliers when handling this tool..
Check Stock