Top Pipe Thread

Carvedexquisitely Bulkhead Water Tank Fitting,1/2" NPT Female Thread,304 Stainless Steel Thru-bulk Fitting

  • Size:1/2" NPT female threaded,the actual diameter of 1/2" thread is 0.84 inch,NPT thread size is not the actual diameter, it is only nominal pipe size..
  • Bulkhead fitting are made of stainless steel, which is corrosion-resistant, rust-proof and has a long service life..
  • Note:The lock nut is Left-hand thread,and the external thread is used for the lock nut and cannot be connected to the pipe..
  • Wide range of uses: commonly used in water tanks, water towers, water inlets and outlets, self-made water storage buckets, rain buckets, and can also be used in various pipes, hoses, pipe fittings or faucets..
  • Bulkhead OD 25mm, suitable for about 25mm ID hole..
Check Stock

Atima Generator Accessories – Extended Run Dual Fuel System Extender Kit for Honda Generator

  • ...ge]:1: Run honda generator fuel extender System Each fuel pipe interface is a quick interface, so it is very convenient to connect .2: When using our products, the generator ,fuel tank and leather pipe are directly connected, not twisted, reducing the distortion of the leather tube and increasing the service life..
  • [Thread fit] :The fuel tank cap thread is tightly coupled with the generator thread, and the rubber gasket is squeezed with the generator port to form a seal to prevent air from entering..
  • [Tips]：The users should buy another tank with Thread outlet to connect this system , like attwood 8806LPG2S Epa Certified Portable Fuel Tank.The model number of the generator must match the model of the fuel cap.In use, as for the users except Honda generator users, the tank should be placed at a higher position than the generator, using gravity to transport oil.Carefully rotate the fuel tank cap on the generator to prevent damage to the plastic thread on the fuel tank..
Check Stock

Blue 2\ x 100' Pool Pump Water PVC Hose - Backwash Filter Discharge Drain Hose - Blue Lay Flat Trash Pump Rubber Hose

  • Male coupling - Aluminum 2 inch Pipe Thread (NPT).
  • Female Coupling - Brass 2 inch Straight Pipe Thread (NPSH) With Gasket.
  • The Female Coupling Will Only Connect To A Male 2 inch NPT PVC Pipe, Pool Pump or Metal Pipe.
Check Stock

GY6 ATV 50cc 80cc 90cc 125cc 150cc 200cc Scooter Exhaust Pipe Bolt, nut Gasket + Exhaust Pipe Gasket + Gloves

  • Applicable to GY6 ATV 50cc 70cc 80cc 90cc 125cc 150cc 200cc scooters, go karts, four-wheel pit cars and mopeds..
  • Product size: exhaust pipe nut 32mm / 1.26in long, thread M6 is 5.8mm/0.22in. Nut / cover: 32 mm long / 1.26 inch, 5.1 mm / 0.2 inch thread M6..
  • Thickened gasket, bolt spacing 49mm, inner hole 27mm, double-sided, double-layer thickness! The exhaust pipe will no longer make noise!.
  • The kit includes: 4 exhaust pipe nuts, 4 exhaust pipe bolts, 2 exhaust pipe long bolts, 6 exhaust pipe washers, 2 thickened exhaust pipe washers, 4 flat washers, 4 spring washers and gloves..
  • Please compare your parts with the pictures before purchasing..
Check Stock

(2 pcs) Drettyer Brass Pipe Adapter Plumbing, G Thread 1/2" Male to NPT Thread 1/2" Male Pipe Fitting Adapter 2 inch long, Seamless and Leakproof

  • ✅Size - G1/2" Male ,NPT 1/2 " Male,2 inch length..
  • ✅Material - High grade solid brass, strong and wear resistant, more durable than iron and iron galvanized pipe fittings.Brass is corrosion resistant and can be used in wet environments..
  • ✅Purpose - G1/2" Pipe fittings Male Thread Water Pipe to 1/2" NPT Adapter.It can be applied to most of the pipes or fittings adapters, or a variety of scene needs..
  • ✅Seamless Connection - Metric BSP 1/2" (G) male to NPT 1/2" male pipe fitting converter (Brass).The seamless close nipple brass fittings and the overall threaded design will make the installation seamless.This will be more beautiful..
  • ✅Tips - Drettyerr is committed to providing quality products. The deeper and smoother thread design will make the installation process easier and more efficient.(Please note, NPT Thread Size is a nominal pipe size and it does not represent the actual diameter.).
Check Stock

uxcell 20pcs Rubber End Caps 1/4\(6mm) ID Vinyl Round Tube Bolt Cap Cover Thread Protectors Black

  • 【Widely Application】1. All kinds of pipe ends protection: plastic pipe, metal pipe, oil pipe, water pipe, vacuum pipe.
  • 2 Thread protection: bolt, screw, nut thread protection.
  • 【Widely Application】3. For shelf, fence, rail protection.
  • 4. For furniture, chair, dining table, stool, hammock decoration protection.
  • 5.For hole cover, protect, decorate, seal (drain hole).
  • 【Size Selection】Because rubber material is soft and elastic, we recommend choosing rubber end cap that is slightly smaller than the outer diameter of the product to be protected. For example: the outer diameter of your product is 9.8mm dia, choose the rubber cover of 9.5mm!.
  • 【Rubber Material】Soft, Elastic, Accurate Size, Oil Resistance, Heat Resistance, Dust Resistance, Long Service Life.
Check Stock

National Hardware N222-463 2193BC U Bolt in Stainless Steel

  • Inside Width/Compatible Pipe Diameter: 1 inch.
  • Used to secure pipe, conduit, cable or other cylindrical objects.
  • Requires pre-drilled holes (hole should be the same diameter as the threaded post).
  • Thread Type: Coarse, Thread Class: UNC-2A, Point Style: Blunt.
Check Stock

Anderson Metals 56120-0806 Brass Pipe Fitting, Adapter, 3/8' Male Pipe x 1/2' Female Pipe

  • Adapter for connecting pipes or fittings of different types.
  • Male National Pipe Taper (NPT) threads on one end and female NPT threads on the other for connecting pipes with different ends. Please see NPT Thread - chart to determine the correct size required. Pipe Size and actual Thread OD are different. The Thread OD is larger than the Pipe Size..
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Operating temperatures range from -53 to 121 degrees C (-65 to 250 degrees F).
  • Meets specifications ASTM B584 and ASME/ANSI B16 for quality assurance.
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
Check Stock

Hooshing Brass Pipe Fitting, 1/2' Female to 1/2' Male Pipe Nipple Extension Connector Fitting, Hex Bushing Adapter, Reducer Adapter, Solid Brass Length 1.97 Inch/50mm

  • 【Material】High quality soild brass for corrosion resistance, high temperature ductility and low magnetic permeability. Strong and durable..
  • 【Size】1/2 Inch Female x 1/2 Inch Male Thread, the thread is NPS, have no tapered. It's straight thread..
  • 【Extension Design】Length: 1.97 Inch/50 mm, can be used to extend the length of the pipe or fitting.Deeper and smoother threads makes work easier and more efficient..
  • 【Widely Applications】Use to extend shower fixtures/arms through walls, extend tub spouts.Also be used with grease, fuels and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
  • 【Note】Brass pipe fittings for connecting pipes or fittings of different thread types, can be used in wet environments.Not recommended for potable water..
Check Stock

Joywayus Hex Nipple 1/2' Male x 1/2' Male Threaded Stainless Steel 304 Threaded Nipple Pipe Fittings for Brew Kit Home Piping (Pack of 5)

  • 【Size】1/2" Male x 1/2" Male Thread. Tapered thread. Pipe fittings are components used for connecting, terminating, controlling flow, and changing the direction of pipe..
  • 【High Quality Material &Threads】Made of quality stainless steel 304, durable and sturdy corrosion resistance, ductility at high temperatures, and low magnetic permeability. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip..
  • 【Hex Nipple】The hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench..
  • 【Operating temperature range】Temperature rating: -65 to 250 degrees F.
  • 【Widely Applications】Male threads for connecting to female threaded pipes, this premium pipe fitting can be used to connect various pipes, such as air pipe, fuel pipe, water pipe as well as air tools.
  • it can also be used with grease, fuels, LP and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
Check Stock

uxcell Spiral Point Plug Threading Tap M8 x 1.25 Thread, Ground Threads H2 3 Flutes, High Speed Steel HSS 6542, Titanium Coated, Round Shank with Square End

  • Different from the traditional carbon steel material. Our pipe taps is made of composite steel (GCR15) material, which is more durable and Higher hardness, (The traditional hardness of 45# carbon steel is 44.
  • the hardness of combined steel is 61), uses forclean and or re-thread damaged or jam pipe threads..
  • 5 pcs NPT Pipe taps used for clean and or re-thread damaged or jam pipe threads, Cuts internal threads in pipes. Ideal for pipe fittings.Available in National Pipe Taper (NPT) and British Standard Pipe Taper (BSP). Includes teach size of: 1/8" - 27 npt, 1/4" - 18 npt, 3/8" - 18 npt, 1/2" - 14 npt, 3/4" - 14 npt..
  • Nominal size of the tap is that of the pipe fitting being tapped..
  • Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications..
  • Round shank with square end, Straight flute tools allow chips to collect in the flutes as they cut and are well suited for most applications in shallow cuts..
Check Stock

6505-08-08 Hydraulic Fitting 1/2\ Female JIC Swivel X 1/2\ Male Pipe Carbon Steel

  • 6505-08-08 HYDRAULIC FITTING 1/2" FEMALE JIC SWIVEL X 1/2" MALE PIPE (Tube O.D. / Hose I.D. Size).
  • THREAD SIZES FOR 6505-08-08 HYDRAULIC FITTING 3/4"-16 FEMALE JIC SWIVEL X 1/2" MALE PIPE.
  • THIS PART NUMBER IS OFTEN REVERSED IN THE INDUSTY. PLEASE VERIFY THE THREAD SIZES BEFORE PURCHASING.
  • TO MEASURE THREAD SIZE, CALIPERS WORK BEST.
Check Stock