Top Plastic Hose Fitting

Dixon Valve BPN252 Brass Push-On Hose Fitting, 1/4\ NPTF Male (Dryseal) x 5/16\ Hose ID Barbed

  • Push-on fitting are intended for use with Lok-On (push-on style) hose only.
  • Lok-On fitting will properly grip Lok-On hose only when pushed all the way in, with the cut end of the hose completely concealed by the plastic cap.
  • 1/4-inches NPTF male and 5/16-inches hose ID barbed.
Check Stock

Dixon Valve BPN42 Brass Push-On Hose Fitting, 1/4\ Male NPTF x 1/2\ Push-On Hose ID Barbed

  • Dixon push-on fitting are intended for use with Lok-On (push-on style) hose only.
  • Lok-On fitting will properly grip Lok-On hose only when pushed all the way in, with the cut end of the hose completely concealed by the plastic cap.
  • 1/4-inches male NPTF and 1/2-inches hose ID barbed.
Check Stock

Class A Customs | 25 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2500-BPK-PUMP

  • ... +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
  • classAcustoms 12 VOLT Fresh Water Pump MODEL # 12V3 - FRESH WATER USE ONLY - OPEN FLOW 11.6LPM / 3.0GPM AMPS 4.0A MAX AMPS 8.0A SHUT OFF PRESSURE 45PSI/3.1 Bar ON-DEMAND PUMP only turns on when senses pressure changes in line 12 VOLT POWER ....
Check Stock

Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP

  • ... +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
  • classAcustoms 12 VOLT Fresh Water Pump MODEL # 12V3 - FRESH WATER USE ONLY - OPEN FLOW 11.6LPM / 3.0GPM AMPS 4.0A MAX AMPS 8.0A SHUT OFF PRESSURE 45PSI/3.1 Bar ON-DEMAND PUMP only turns on when senses pressure changes in line 12 VOLT POWER O....
Check Stock

Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP

  • ... +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
  • classAcustoms 12 VOLT Fresh Water Pump MODEL # 12V3 - FRESH WATER USE ONLY - OPEN FLOW 11.6LPM / 3.0GPM AMPS 4.0A MAX AMPS 8.0A SHUT OFF PRESSURE 45PSI/3.1 Bar ON-DEMAND PUMP only turns on when senses pressure changes in line 12 VOLT POWER ....
Check Stock

Metalwork 2\ Tri Clamp to 1\ Hose ID Barbed Adapter SUS304 Sanitary Hose Pipe Fitting

  • Adapter for connecting pipes or fittings of different types.
  • Barbed fitting for a tight seal on hoses when used with a hose clamp (not included).
  • For use with rubber hoses: Barb: 1" Barb For Rubber, Plastic, TPU, or other hose.
  • Fits: 1.5" Tri Clamp / Clover / Sanitary Fitting.
Check Stock

Shoreline Marine Bilge Pump Plumbing Kit | Plastic Bilge Pump Hose | 2 Stainless Steel Hose Clamps | Easy Installation | Heavy-Duty Marine Accessory

  • BILGE PUMPS & PLUMBING: The kit is among the functional boat accessories that allow you to remove the accumulated water from the bilge. This kit consists of a plastic bilge pump hose, thru-hull fitting, and 2 stainless-steel hose clamps..
  • HIGH COMPATIBILITY: Irrespective of the size of the boat, this high utility water pump works in accordance with 3/4" x 5" of the plastic bilge hose. This kit contains everything you need for bilge pump installation..
  • EASY TO USE: With a pack of all the essential parts and equipment required to perform the pumping task, this kit makes it one of the best marine boat accessories. It is fast and easy to use..
  • DIMENSIONS: The kit consists of 3/4 inches and 5 inches of plastic bilge pump hose, along with a thru-hull fitting and 2 stainless-steel hose clamps that work efficiently to remove the excess water from the hull. It works wonders with a bilge pump float switch..
  • CALCUTTA OUTDOORS: A leading manufacturer of consumer products for the outdoor sports and recreation market providing performance-driven products, including fishing rods, ta....
Check Stock

Anderson Metals - 57002-0604 Brass Hose Fitting, Connector, 3/8\ Barb x 1/4\ Female Pipe

  • Adapter for connecting pipes or fittings of different types.
  • Fitting connects to hose on one end and has an NPT female connector on the other.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Barbed fitting creates a tight seal on flexible and semi-rigid hose when used with a hose clamp or crimp sleeve or ferrule (sold separately).
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
Check Stock

Joywayus 1/4'(6mm) ID Hose Barb 4 Way Union Fitting Pipe Cross Intersection/Split Brass Water/Fuel/Air

  • 1/4" barb tee to connect 1/4" I.D. hose,we can provide customized orders,including oem..
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
  • Barbed fitting creates a tight seal on flexible and semi-rigid hose when used with a hose clamp or crimp sleeve or ferrule (sold separately).For use with plastic or rubber hose.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
Check Stock

F-AL-3/8, 3/8″ Threaded Female Tank Filter for Mosquito Misting Systems

  • ... Specifications} 110 Volt Kit Includes: – 200PSI Booster Pump with Plug (110v) – 50ft Flexible Tubing – Calcium Inhibitor Filter – 12 Brass/Stainless Steel Mist Orifice Nozzles – 0.012” – 11 – Push Lock Mist Tees – 1 – Push Lock End Mist Elbow – 6ft Feed line with 3/4 Garden hose connector – Plastic Clamps.
  • {Installation} – Push Lock Fittings – Easy Connect -Whisper Quiet Operation Easy to hook with any garden hose Max Water pressure 200 PSI Supports up to 20 Nozzles Wall Mountable Plugs in to standard 115V outlet (wall plug included on 110v models only).
  • {Comes with Filter to protect your Nozzles} Booster Pump Features: Built-In Thermal Safety Switch Supports up to 20 Nozzles 110v AC 1.2 Amps 0.50GPM Wall Plug (on 110v pumps only) Inlet Fitting: 3/4” Garden Hose Connecter Outlet Fitting: 1/4” and/or 3/8” Push Lock.
  • {Easy to Expand} Booster Pump Features: Supports up to 20 Nozzles 110v AC 1.2 Amps 0.50GPM Wall Plug (on 110v pumps only) Inlet Fitting: 3/4” Garden Hose Connecter Outlet Fitting: 1/4” and/or 3/8” Push Lock. MC12020.
Check Stock

Brass Hose Barb Tee 1/4 x 1/4 x 1/4 Barbed T -Fitting 3 Ways Air Hose Fittings Pack of 5

  • 1/4" barb tee to connect 1/4" I.D. hose,we can provide customized orders,including oem..
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
  • Barbed fitting creates a tight seal on flexible and semi-rigid hose when used with a hose clamp or crimp sleeve or ferrule (sold separately).For use with plastic or rubber hose.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
Check Stock

10 Foot Long Dust Collection Power Tool Hose Kit for Multiple Types/Brands of Power Tools and Work Shop Vacuums with Threaded Fittings

  • ...s kit will also work with popular tools like the K4 and the K5 Pocket Hole Jig. Using this hose with your tools will keep your shop cleaner and can be quickly coiled up for easy storage.
  • The large thread-on rubber fitting has a 1-1/2 inch I.D. with a 1-13/16 inch O.D. which works on many other power tools. The rigid plastic vacuum Plug-in Adaptor has a 2-1/4 inch taper up to 2-5/16 inch O.D. The adaptor is designed to plug into most standard workshop vacuum ports. The Plug-in Adaptor conveniently threads onto the power tool hose so it will never slip off!.
  • Included inside the box: 1 each ten foot long 1-3/16 inch O.D. small diameter flexible hose, 1 each small flexible rubber thread-on fitting, 1 each large flexible rubber thread-on fitting and 1 each Plug-in Adaptor shop vacuum that will allow you to connect the hose to most commercial or residential workshop vacuum ports..
  • IMPORTANT! CHECK YOUR POWER TOOL PORT DIMENSIONS: Before placing an order, please check the inner and outer (I.D. and O.D.) diameter of your workshop vacuum ports and power tool ports to make sure the hose and fittings will properly fit and work for your needs. THE I.D. AND O.D. ON THE RUBBER END FITTINGS AND HOSE ARE APPROXIMATE SIZES AND MAY SLIGHTLY VARY..
Check Stock