Top Rotary Potentiometers - BuyWiseBest.com

Fender Telecaster/Precision Bass Knobs - Knurled Chrome

Package includes two knurled flat-top knobs and mounting set screws.
Designed to fit most 1/4" solid shaft potentiometers.
Fits most Telecaster and Precision Bass instruments (US and Mexico) manufactured from '51-Present.

Set of 3 (Volume, Volume, Tone) black knobs with set screws and white indicator lines.
Designed to fit 1/4" solid shaft potentiometers.
Fits most Jazz Bass models (US and Mexico) made from 1964-Present.

17 action buttons with “braille”-style identification.
Inspired by the iconic Airbus sidestick: Ergonomic 1:1 scale replica.
4 swappable joystick head button modules, and 12 remappable buttons for a multitude of possibilities in flight, and on the ground.
Throttle with built-in thrust reverser mechanism, and rudder control by rotating the sidestick’s handle (lockable/unlockable).
Contactless magnetic sensor technology, with no potentiometers, for an unlimited lifespan and optimal precision.

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

[EL2 FU 10K for PS4/PS3 Controller] – 4x replacement analog joystick was found in some PS4 DualShock 4 came with PlayStation 4 Pro, and some PS3 controllers also use this version. The thumbstick module was made by Favor Union (FU). The stick controller comes with 10KΩ trimmer potentiometers in orange.
[Compatibility] – The 14 prongs were positioned as the same as ALPS edition. Technically, the whole unit is interchangeable with EL1 ALPS 10K used in PS4 controllers, and other brands like ‘Scuf’ and ‘Razer Raiju Ultimate’ with ALPS joysticks inside. However, the trim pot resistor alone is not interchangeable with ALPS edition.
[Additional Resistor] – Complicated moving mechanism and daily wear and tear finally caused drifting. Even new sensors cannot be 100% balanced. Calibrating in controller settings might not work. We packed 10x correction resistors to solve the potential problem in hardware level. Solder one or two paralleled tiny resistors onto the potentiometer at the opposite direction against drifting. It will help correct 3 to 5 degrees drifting.
[When to replace] – The analog joystick needs to be replaced when your controller has the problem of drifting, creeping, stuttering, a blind spot, a dead spot, a dead zone, no react....