Top Screwed Pipe Fitting

boost/vacuum gauge silicone coupler adapter - Car Turbocharger Pipe Fitting Universal Turbocharger Silicone Boost Pipe Hose Nipple Turbo Vacuum VAC Gauge Fitting TDI

  • Wide Application---The turbocharger pipe fitting is suitable for a 4mm inner diameter pipe. 100% brand new aftermarket Boost Pipe Fitting that has never been used.
  • For Boost Gauge---This boost hose nipple fitting allows you to fit a boost gauge or any other type of instrument where vacuum or boost pressure is required.
  • Superior Quality Aluminum Alloy---The turbo boost pipe hose nipple is made of high quality aluminum alloy and durable to use. The manufacture of the fitting meets the strict quality requirements.
  • Easy Installation---The turbocharger mounting kit is easy to install, simply drill a 8mm hole in your silicone boost pipe and push the nipple through the hole (from the inside), put on the sealing o-ring, washer and tighten down with the nut.
  • Quality Assurance---As a professional seller, we provide high quality products and considerate services. Every product must go through strict inspection to ensure reliable quality. Please rest assured to buy our products, hope you have a pleasant shopping experience.
Check Stock

Oatey 30863 Heavy Duty Solvent Cement, 8 Oz, Can, Liquid, Clear

  • Heavy duty Clear cement for use on all schedules and classes PVC pipe and fitting up to 12” diameter with interference fit, up to 18” for non-pressure.
  • Low-VOC solvent cement meets California South coast air quality management district (SCAQMD) 1168/316a or baaqmd method 40 and various environmental requirements.
  • Heavy Duty Clear cement for use on all schedules and classes PVC pipe and fitting up to 12î diameter with interference fit, up to 18î for non-pressure.
  • Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD).
  • Thick formula fills gaps in large diameter pipe and loose fitting joints.
  • Recommended for potable water, pressure pipe, conduit and DWV.
  • Recommended application temperature 40°F to 110°F / 4°C to 43°C.
Check Stock

iCrimp CRQ01 Disconnect Tong Sized 1/2 inch, 3/4 inch, 1 inch, Removal Tool used for Demount Brass Push Fit, Push-to-Connect Fittings

  • CRQ01 Push-Fit fitting disconnect tool has 3 teeth available in 1/2 in., 3/4 in. and 1 in. sizes, allows for easy removal of brass push-to-connect fitting from pipe.
  • CRQ01 disconnect tong is the easiest way to disconnect brass Push to Connect fittings in hard to reach places where it can be tough to get leverage on the release collar.
  • Compact design with wide grip handles. One-handed operation. Quick and easy disassembly.
  • To use the disconnect tong, slide the tong over the fitting and the pipe. Squeeze the tong to press the fittings collar and pull the pipe from the fitting. Easier to use in tight situations.
  • The disconnect tool depresses the release collar using the force applied by your hand to allow the teeth of the fitting to release and the fitting to be removed, reducing the risk of installation errors.
Check Stock

Brooklyn Pipe Flange - 16 Pack 3/4' Black Floor Flange Cast Iron Pipe Fittings | Our 3/4 Inch Pipe Flange | Industrial Pipe Flanges | Decorative Pipe Fitting Fit for Steampunk Furniture

  • 3/4 INCH FLOOR FLANGE - Our Brooklyn Pipe floor flange is a great choice for all your DIY needs. This decorative flange is the perfect pipe fitting to take your project to the next level. These fittings are for DIY projects only, they are not rated to carry gas nor water..
  • INDUSTRIAL DECOR- Our 3 hole black floor flange is 2.75" inches in diameter and provides a unique look for all projects. Whether you're looking for an industrial, steampunk, vintage, retro, factory look, our flange will fit perfectly into your project..
  • SUPPORT AMERICAN BUSINESS – Brooklyn Pipe is a small business headquartered in New York. We would really appreciate the opportunity to show you what makes Brooklyn Pipe the #1 top rated pipe fitting brand. We always go the extra mile for our awesome customers!.
  • NO CHINA STAMP - Our forged malleable iron flange doesn't have the word "CHINA" stamped into the flange which is another reason why Brooklyn Pipe stands out in the pipe fitting products that are on the market. Our 3 hole flange is just as strong as the competition but simply looks better!.
  • QUALITY CONTROL - We’ve partnered with world class steel factories and hire licensed inspectors to review our Brooklyn Pipe products prior to being packaged. Rest assured you are getting to....
Check Stock

PVC- 4 way L/T 2' (Furniture Grade White)

  • DO NOT use these fittings for plumbing projects..
  • The 4 way LT PVC pipe fitting, also known as a side outlet tee or 4 way corner fitting is commonly used to build the sides of a box or cube out of PVC pipe. It is also useful to make the ridge on PVC greenhouses or small PVC buildings. Some dog agility customers use the 4 way LT at the base of jump pole stands..
  • All four outlets are non-threaded sockets.
  • 2" Fittings fit on 2" Schedule 40 PVC or Furniture Grade PVC. Please check out our PVC Sizing Guide (Specification Sheet) to make sure that you order the correct size PVC Fittings. PVC is NOT measured by the outside diameter, and doing so will result in receiving fittings that are too big for your pipe..
  • Furniture Grade means this fitting has a non-marked, glossy finish..
Check Stock

1-1/2" 4-way Tee PVC Fitting Connector

  • Furniture Grade means this fitting has a non-marked, glossy finish..
  • DO NOT use these fittings for plumbing projects..
  • The 4 way LT PVC pipe fitting, also known as a side outlet tee or 4 way corner fitting is commonly used to build the sides of a box or cube out of PVC pipe. It is also useful to make the ridge on PVC greenhouses or small PVC buildings. Some dog agility customers use the 4 way LT at the base of jump pole stands..
  • 1-1/2″ Fittings fit on 1-1/2″ Schedule 40 PVC or Furniture Grade PVC. Please check out our PVC Sizing Guide (Specification Sheet) to make sure that you order the correct size PVC Fittings. PVC is NOT measured by the outside diameter, and doing so will result in receiving fittings that are too big for your pipe..
  • All four outlets are non-threaded sockets.
Check Stock

Class A Customs 13 Gallon Water Tank & Plumbing Kit T-1300-BPK

  • ...Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • 13 GALLON TANK MEASUREMENTS 21” x 9” x 16”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adapter (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adapter (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adapter (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Spears 1429 Series PVC Tube Fitting Coupling Schedule 40 Gray 1-1/2 x 1 Barbed

  • Fitting connects to schedule 40 PE pipe on both ends.
  • PVC for strength and resistance to reactions with acids, gasoline, alcohol, and hydrocarbons.
  • Barbed fitting creates a tight seal on flexible pipe when used with a hose clamp (sold separately).
  • Meets ASTM D 2609 standards for plastic insert fittings and certified by NSF for use with potable water.
Check Stock

Spears 1429 Series PVC Tube Fitting Coupling Schedule 40 Gray 3/4 x 1/2 Barbed

  • Fitting connects to schedule 40 PE pipe on both ends.
  • PVC for strength and resistance to reactions with acids, gasoline, alcohol, and hydrocarbons.
  • Barbed fitting creates a tight seal on flexible pipe when used with a hose clamp (sold separately).
  • Meets ASTM D 2609 standards for plastic insert fittings and certified by NSF for use with potable water.
Check Stock

SINTLY 3/8\ NPT to 6AN Flare Male AN6 Straight Fitting Union Flare Adapter Aluminum Black 2Pcs

  • 【Tips】To obtain a proper seal in the NPT joint, you need to use a sealant compound or PTFE tape. The thread is sealed by wedging. The NPT connection cannot be reused. When accessories are reused, this can cause wear or increase the possibility of leakage..
  • 【37 Degree Flare Fitting Taper】：The 6an male flare to 3/8" NPT fitting has one male side AN is a 37-degree flare fitting taper and the other male side NPT is a 60 degree tapered threads. These adapter hose fittings are designed to quickly make professional 37° AN connections from NPT tapered pipe threads. Designed for smooth flow that gives better fluid flow, tight security, and leaks free.
  • 【Application】-6AN to 3/8" NPT straight flare to pipe adapter is widely used in kinds of liquids, oil, Water, Air, Fuel lines, E85, gas, etc. Bulkhead Fitting is perfect to apply in automotive, industrial, boat/marine, etc. The male flare fitting fit all oil cooler / fuel tank / fuel pump/fluid Line/turbo..
  • 【Material ＆ Features】Made of High-Performance Lightweight 6061-T6 Billet Aluminum Material. All threads are designed for the maximum percentage of engagement. One side is AN standard and the other is NPT National Pipe Taper Thread. Each straight fitting is completed with a black anodized fini....
Check Stock

Class A Customs | T-1000-BPK| 10 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 10 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-2100-BPK| 21 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 21 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34” Longest Length (not including fittings) x 9” x 16” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock