Top Separate Logic Voltage Support

Comidox 1Set USB Logic Analyzer Device Set USB Cable 24MHz 8CH 24MHz 8 Channel UART IIC SPI Debug for Arduino ARM FPGA M100 Hot

  • This item is an inexpensive logic analyzer designed to be compatible with Saleae Logic Analyzer software, but this item is not an official Saleae product. This item is also supported by the free software by Sigrok called PulseView..
  • Sampling rate up to: 24 MHz , can be 24MHz. 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500KHz, 250KHz, 200KHz, 100KHz, 50KHz, 25KHz..
  • The logic for each channel sampling rate of 24M/s. General applications around 10M, enough to cope with a variety ofoccasions..
  • A total of 8 digital channels, the voltage range is 0V and 5.5V, of which 1.5V is the voltage threshold, below 1.5V is considered low, above 1.5V is considered high..
  • UART, SPI, IIC and other communication debugging, let you get twice the result with half the effort. 24M sampling rate, can automatically analyze UART, IIC, SPI and many other standard protocols..
Check Stock

Graphtec America GL240 Data Logger

  • 10 Channels for Voltage, Temp, Humidity, Pulse and Logic Measurements.
  • Isolated Input System Ensures Signals are Not Corrupted by Other Channels.
  • Supports 20mV to 100 Volts, Thermocouple Type: R, S, B, K, E, T, J, N and W and 4 Pulse or Logic Channels with Optional Cable (#B-513).
  • WLAN Compatible Using GL100-WL and Optional Wireless LAN Unit (B-568).
Check Stock

DKARDU USB Logic Analyzer Device 24MHz 8CH 8 Channel UART IIC SPI Debug with Mini USB Cable Dupont Cable 6 Colors Test Hook Clip Set for Arduino FPGA M100 SCM

  • 【Product introduction】: This item is an inexpensive logic analyzer designed to be compatible with Saleae Logic Analyzer software..
  • 【Applicable to various occasions】: The logic sampling rate of each of the 8 channels is 24M/s, generally about 10M, which is sufficient for various occasions.
  • 【Channel value】: A total of 8 digital channels, the voltage range is 0V and 5.5V, of which 1.5V is the voltage threshold, below 1.5V is considered low, above 1.5V is considered high..
  • 【Sampling rate up to】: 24 MHz , can be 24MHz. 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500KHz, 250KHz, 200KHz, 100KHz, 50KHz, 25KHz..
  • 【Automatic analysis】: UART, SPI, IIC and other communication debugging, let you get twice the result with half the effort. 24M sampling rate, can automatically analyze UART, IIC, SPI and many other standard protocols..
Check Stock

4Pack L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 (4 PACK)

  • Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability..
  • This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage..
  • Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability..
  • Dual-channel H-bridge driver working mode creates higher working efficiency.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
Check Stock

USB Logic Analyzer Device with EMI Ferrite Ring USB Cable 24MHz 8CH 24MHz 8 Channel UART IIC SPI Debug for Arduino ARM FPGA M100 SCM

  • The logic for each channel sampling rate of 24M/s. General applications around 10M, enough to cope with a variety ofoccasions.
  • Sampling rate up to: 24 MHz , can be 24MHz. 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500KHz, 250KHz, 200KHz, 100KHz, 50KHz, 25KHz.
  • Input Impedance: 1Mohm || 10pF (typical, approximate).
Check Stock

ACEIRMC 8pcs L298N Motor Driver Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power MEGA R3 Mega2560

  • When you are driving voltage (above logo for the 12 v input, can actually accept input range is 7 to 12 v) for 7 v to 12 v, can make to onboard power supply 5 v logic, when using the onboard after 5 v power supply, interface of + 5 v The power supply does not input voltage, but can yield 5V voltage for external use..
  • The chip manual proposes to support 35V, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven.
  • Great for for Arduino DIY Smart Car Robot Power MEGA R3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
  • No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
Check Stock

NXP 74HC4052N 74HC4052 - Dual 4-channel analog multiplexer/demultiplexer DIP16 1 Pack

  • Wide analog input voltage range from -5 V to +5 V.
  • Logic level translation: to enable 5 V logic to communicate with ±5 V analog signals.
  • Typical ‘break before make’ built-in.
Check Stock

Bridgold 10pcs 74HC4051 74HC 8-Channel Analog multiplexer, Signal Splitter,16-DIP

  • Logic level translation: to enable 5 V logic to communicate with ± 5 V analog signals.
  • Typical “break before make” built in.
  • The products have been strictly screened, with stable performance and reliable data output..
Check Stock

2 Set 24MHz 8CH 24MHz 8 Channel USB Logic Analyzer Device with EMI Ferrite Ring USB Cable UART IIC SPI Debug Compatible with Ar-duino ARM FPGA M100 SCM

  • The logic for each channel sampling rate of 24M/s. General applications around 10M, enough to cope with a variety ofoccasions.
  • Sampling rate up to: 24 MHz , can be 24MHz. 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500KHz, 250KHz, 200KHz, 100KHz, 50KHz, 25KHz.
  • Input Impedance: 1Mohm || 10pF (typical, approximate).
Check Stock

10Pcs 4N25 6Pin Optoisolators Transistor DIP New

  • Product name: MOC3061 DIP-6 Optoisolator.
  • Simplifies Logic Control of 115/240 Vac power. Zero Voltage Crossing.
  • dv/dt of 1500 V/µs Typical, 600 V/µs Guaranteed.
  • They are designed for use with a triac in the interface of logic systems to equipment powered from 115/240 Vac lines, such as solid–state relays, industrial controls, motors, solenoids and consumer appliances,etc..
  • Package Include: 10Pcs/20Pcs/50Pcs/100Pcs.
Check Stock

20 Pieces 3 Pins AMS1117-3.3 DC 4.75V-12V to 3.3V Voltage Regulator Down Power Supply Buck 800mA Module

  • How to install: please check the product pictures carefully for the wiring diagram steps before using, simple dual-panel design and the input output using the 3 pin single row pin for easy connection, the input voltage is higher than output voltage 1.2V, the module will work normally.
  • AMS1117-3.3 is a positive voltage regulator step down power supply module, support DC 4.75-12V input and 3.3V fixed voltage and 0.8A current output.
  • Electronic devices partner: the 3 pins AMS1117-3.3 voltage regulator mini step down power supply module, can be applied to electronic devices which need 3.3V power supply, such as SCM project design, MCU development and more, easy to be connected and provide the power supply.
  • Where to use: the voltage to 3.3V 800mA DC buck module is applicable for high-efficiency linear regulator published active power regulator battery charger active instrument.
  • Compatible with: the 3 pins AMS1117-3.3 voltage regulator mini power supply is compatible with Arduino MEGA2560, MSP430 development board, 3.3V low power consumption MCU, FPGA/CPLD PLD programmable logic systems, ARM7 ARM9 ARM11 STM32, etc..
  • Provide more safety: the AMS1117-3.3 800mA DC buck module features overheat shutdown circuit provides overload and over-temperature protectio....
Check Stock

Songhe HM-10 Bluetooth 4.0 BLE iBeacon UART Module with 6PIN Base Board for Arduino (2PCS)

  • 1. Internal logic level conversion circuit. No need to externally convert 5V level to 3.3V level.
  • 2. The power input port is equipped with anti-reverse circuit. Avoid accidental power plugging, which may cause the module to burn out..
Check Stock