Top Solid State Latching Relay

uxcell BEM-14840DA 3-32V DC to 24-480V AC 40A Output Single Phase SSR Solid State Relay

  • Total Size (Approx.) : 58 x 45 x 32mm / 2.3" x 1.8" x 1.26" (L*W*T).
Check Stock

Opto 22 DC60MP MP Model DC Control Solid State Relay, 60 VDC, 3 Amps, 4000 VRMS Isolation Voltage

  • Special attention: the current of this product is 10A for a long time.A large heat sink or fan need to be added.Model: SSR-40DA Solid State Relay 40A DC to AC.
  • Input voltage: 3-32V DC Output voltage: 24-380V AC.
  • Item size: 6.2 x 4.5 x 2.3cm/ 2.4 x 1.8 x 0.9inch(L*W*H).
Check Stock

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

  • Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
  • Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
  • Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
  • This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
  • Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
Check Stock

RF Mini Wireless Remote Controller for Single Color 3528 5050 LED Strip Lights, Wireless Remote Control with DC Connector, RF Dimmer for 12V DC LED Ribbon, Shelf Lights

  • ...y for its low repetitive rate and re-learn mode, by which it can delete the old code and re-learn a new code when a remote control get lost, so you are always in control of it..
  • 3. Remote Relay with 3 Modes of Operation – Use a jumper to configure 3 modes of operating selection pulse / momentary, hold / toggle and latching mode. 4 independent relay channels can either work together (in latching) for polarity reversing or individually (in pulse / hold) to control different electronics, such as two channels for garage door controller motor, the other two for entry lights..
  • 4. Easy and Flexible Switch Relay – The wireless relay kit is a perfect remote switch for those hobbyists with home automation DIY projects or business Industrial electrical. The power input voltage is 12V, and each receiver’s relay capacity is up to [email protected] and [email protected]..
  • 5. Wide Applications – The wireless remote control switch can be widely used in short and long range turn devices on / off wirelessly, anti-theft alarm control panels, lifts, boats, motor-driven curtain, roller blinds, garage door openers, gate barriers, motorcycles, vehicles, cars, trucks, RVs, electric generator, electric door release locks, windows, manual switches extender, LED lighting ....
Check Stock

TWTADE 2PCS SSR-25 DA 25A 3-32V DC / 24-380V AC SSR Single Phase Solid State Relay ssr-25da

  • Special attention: The current of this product is 10A for a long time.A large heat sink or fan need to be added.Model: SSR-25DA Solid State Relay 25A DC to AC.
  • Input voltage: 3-32V DC Output voltage: 24-380V AC.
  • Item size: 6.2 x 4.5 x 2.3cm/ 2.4 x 1.8 x 0.9inch(L*W*H).
Check Stock

TWTADE 2PCS SSR-40 DA 40A DC 3-32V to AC 24-380V SSR Single Phase Solid State Relay ssr-40da

  • Special attention: the current of this product is 10A for a long time.A large heat sink or fan need to be added.Model: SSR-40DA Solid State Relay 40A DC to AC.
  • Input voltage: 3-32V DC Output voltage: 24-380V AC.
  • Item size: 6.2 x 4.5 x 2.3cm/ 2.4 x 1.8 x 0.9inch(L*W*H).
Check Stock

12V Relay Remote Switch Wireless RF Remote Control Switch 4 Channel Relay Module 433Mhz Transmitter Receiver Kit Universal Remote Controller for Lights Ceiling Fan Garage Door Opener Gate Car & More

  • ...y for its low repetitive rate and re-learn mode, by which it can delete the old code and re-learn a new code when a remote control get lost, so you are always in control of it..
  • 3. Remote Relay with 3 Modes of Operation – Use a jumper to configure 3 modes of operating selection pulse / momentary, hold / toggle and latching mode. 4 independent relay channels can either work together (in latching) for polarity reversing or individually (in pulse / hold) to control different electronics, such as two channels for garage door controller motor, the other two for entry lights..
  • 4. Easy and Flexible Switch Relay – The wireless relay kit is a perfect remote switch for those hobbyists with home automation DIY projects or business Industrial electrical. The power input voltage is 12V, and each receiver’s relay capacity is up to [email protected] and [email protected].
  • 5. Wide Applications – The wireless remote control switch can be widely used in short and long range turn devices on / off wirelessly, anti-theft alarm control panels, lifts, boats, motor-driven curtain, roller blinds, garage door openers, gate barriers, motorcycles, vehicles, cars, trucks, RVs, electric generator, electric door release locks, windows, manual switches extender, LED lighting l....
Check Stock

AITRIP 1PCS 8 Channel 5V Solid State Relay Module Board High Level Trigger Compatible with Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC (1PCS)

  • Solid State Relay Module Board has been assembled, and electrical test passed.
  • Size: 155 x 55 x 24 mm (approximately 6.1 x 2.17 x 0.95 inch).
  • Has been assembled, and electrical test passed. Led indicator for each relay. Size: 155 x 55 x 24 mm (approximately 6.1 x 2.17 x 0.95 inch) Input control signal voltage: 0V - 0.5V Low stage (SSR is OFF), 0.5V - 2.5V (unknown state), 2.5V - 20V High state (SSR is ON).
  • Load voltage range: 75 to 264VAC (50/60Hz).
  • Load current: 0.1 to 2 AMP Standard interface that can be controlled directly by microcontroller (Compatible with Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Check Stock

6PCS SSR-40DA Solid State Relay Single Phase Semi-Conductor Relay Input 3-32V DC Output 24-380V AC

  • Product name: solid state module relay SSR-40DA, 3-32VDC/24-380VAC..
  • SSR Application: with a switch no spark, no noise,high switching speed,anti-corrosion,moisture-proof,anti-vibration,long life.high reliability,electromagnetic compatibility and other characteristics..
  • Solid state relay ideal for automatic process control application, a must component for temperature controller and other machinery control system..
  • Especially suitable for corrosion, moisture, dust, and other harsh environments, and frequent switching the occasion, AC contactor is updated alternative..
  • High reliabily, compact size, a great part for temperature controller and other machinery control system..
Check Stock

MYSWEETY 3PCS SSR-40DA Solid State Relay Single Phase Semi-Conductor Relay Input 3-32V DC Output 24-380V AC

  • Product name: solid state module relay SSR-40DA, 3-32VDC/24-380VAC..
  • SSR Application: with a switch no spark, no noise,high switching speed,anti-corrosion,moisture-proof,anti-vibration,long life.high reliability,electromagnetic compatibility and other characteristics..
  • Solid state relay ideal for automatic process control application, a must component for temperature controller and other machinery control system..
  • Especially suitable for corrosion, moisture, dust, and other harsh environments, and frequent switching the occasion, AC contactor is updated alternative..
  • High reliabily, compact size, a great part for temperature controller and other machinery control system..
Check Stock

CGELE PID Temperature Controller Kit Voltage AC 100V to 240V Comes with SSR 40DA Solid State Relay, K Type Thermocouple Sensor, and Black Heat Sink

  • ♥【What You Get】In this PID temperature controller kit,it include 1 x PID temperature controller,1 x solid state relay 40DA，1 x K type thermocouple，1 x heat sink..
  • ♥【Product parameters】Power supply voltage:110-240VAC 50/60Hz.
  • working environment:ambient temperature: 0℃~50℃,relative humidity: 35%~85% (no condensation) ；storage temperature：-25℃~65℃（avoid ice or dew）；resolution：1℃，0.1℃（adjustable）；wiring method：terminals；accuracy：+0.5%FS.
  • installation environment:installation type ll, pollution grade 2 (IEC61010-1).
  •  max current: 30mA, load resistance:≥1K..
  • ♥【Feature】 Support 2 wire thermocouple input,1 way solid state relay output,1 way relay alarm output.
  • digital display of real-time and set temperatures,adjustable degrees ℉ and ℃..
  • ♥【Size】The panel size of PID temperature controller is 48(W)mmx48mm(L),install hole size is 46(W)mmx46mm(L).Total size:48mm(W)x48mm(L)x76mm(H).
  • ♥【Widely application】Widely used in chemical industry, medical industry, product industry, machinery industry, greenhouse farming, agricultural planting, etc..
Check Stock

CG Solid State Relay SSR-25DA DC to AC Input 3-32VDC To Output 24-480VAC 25A Single Phase Plastic Cover…

  • ♥【What You Get】Each package With 2 mini bag of thermal grease which apply on the back of the SSR to make the temperature dissipate faster..
  • ♥ Product Name: solid state module relay SSR-25DA, 3-32VDC/24-480VAC.
  • ♥ Total size (approximate):58 x 45 x 32mm/2.3" x 1.8" x 1.26" (l*w*t).
  • Material:metal, plastic, electronic parts..
  • ♥ SSR Application: with a switch no spark, no noise,high switching speed,anti-corrosion,moisture-proof,anti-vibration,long life.high reliability,electromagnetic compatibility and other characteristics..
  • ♥ Solid state relay ideal for automatic process control application, a must component for temperature controller and other machinery control system..
Check Stock