Top Surface Mount Car Speakers

JBL Stage 36427 - 4\ x 6\ 2 Two-Way Car Audio Speaker

  • Carbon-injected Plus One cones are larger than others in their size class, meaning they move more air and make more bass.
  • Soft-dome tweeters feature oversized voice coils for greater heat dissipation and higher power handling resulting in smooth, fatigue free highs.
  • The patented I-Mount system allows unparalleled flexibility whether you flush- or surface-mount your component tweeters.
  • A dual-level tweeter volume adjustment helps compensate for less-than-perfect speaker placement, and can even be set to suit your personal listening preference and musical taste.
  • Low-impedance, three-ohm speakers compensate for the undersized wires found in many of today’s cars, and make the most of every watt your car stereo can deliver.
Check Stock

JBL GTO609C Premium 6.5-Inch Component Speaker System - Set of 2

  • Carbon-injected plus one cones are larger than others in their size class, meaning they move more air and make more bass.
  • Soft-dome tweeters feature oversized voice coils for greater heat dissipation and higher power handling resulting in smooth, fatigue free highs.
  • The patented i-mount system allows unparalleled flexibility whether you flush- or Surface-mount your component tweeters.
  • A dual-level tweeter volume adjustment helps compensate for less-than-perfect speaker placement, and can even be set to suit your personal listening preference and musical taste.
  • Low-impedance, three-ohm speakers compensate for the undersized wires found in many of today’s cars, and make the most of every watt your car stereo can deliver.
Check Stock

Pair Rockville RV68.2C 6x8 / 5x7 Component Car Speakers 900 Watts/170w RMS CEA

  • Includes: (2) 6x8” speakers, (2) tweeters, (2) Crossovers, (2) Grills, Flush and surface Mounting accessories, Speaker wire.
  • Rockville RV68.2C 6x8 and 5x7 Component car speakers Peak Power Rating: 900 Watts per Pair / 450 Watts Each.Injection Molded Polypropylene woofer cone gives amazing bass and mids. Flex Motion Butyl Rubber Surround..
  • 1.2” PEI dome tweeter with ferrite magnet give amazing highs. Flush and surface mounting tweeter options. Fine-tuned 2-Way Crossover, 12db/Octave Roll Off. Ferro Fluid Cooled Tweeter Magnet. Steel high quality basket. Rubber magnet boot cover..
  • Frequency response: 32-22,000 Hz. Sensitivity: 91 dB @ 1w/1m. Mount depth: 2.52". Impedance: 4 Ohm. Grilles included. Aluminum voice coils. 100% oxygen free copper voice coil windings. Black electro-plated T-yoke and washers. Cotton spider material..
  • Copper terminals. Cutout diameter: 7.36” x 5.12”. Magnet: 13.5 Oz Y25 magnet. Magnet dimensions: 90mm x 15mm. Fs: 65.102 hz. Re: 3.6 OHM. Qes: 1.663. Qts: 1.173. Qms: 3.977. Fits 6x8” and 5x7” openings..
Check Stock

Halter Adjustable Wall Mounting Surround Sound Speaker Mounts Bracket Clamp Style w/Tilt & Swivel 360° Rotation

  • UNIVERSAL USE: Our wall mount speaker bracket is a pair of ideal wall brackets that can house speakers up to 33 lbs. per unit. It is not solely built for heavy surround sound speakers, but small and lightweight speakers as well. The Halter Universal Speaker Wall Mount Bracket is suitable for various types of walls such as concrete, brick, and wood stud surface..
  • ADJUSTABLE USE: You don't need to worry about upgrading or downsizing your speakers. This universal speaker wall mount features an adjustable clamp that can hold speakers that are sized 5.4 to 11.7 inches. This is designed with a clamp-type speaker mount to keep narrow and wide speakers secured and in place. The sound speaker bracket offers mounting solutions for home and office use..
  • SURROUND SOUND SETUP: Our speaker bracket with adjustable mount can be tilted 8 degrees up and 8 degrees down with a left to right swivel action that is up to 180 degrees. This is a great design to maximize and accommodate various ideal surround sound effects to achieve your desired sound fidelity and depth..
  • QUICK AND EASY INSTALLATION: You can assemble and do the installation by yourself and in a breeze. The packaging includes all standard mounting hardware, fixing screws, and a cable management system so there's....
Check Stock

Infinity REF-6522EX Shallow-Mount 6-1/2 Inch Coaxial Car Speakers

  • Shallow-mount 6-1/2″ Coaxial car speakers.
  • 6-1/2″ 2-way car speakers Plus One+ polypropylene woofer cone with hi-roll rubber Surround.
  • 1″ edge-driven, textile dome tweeter included brackets allow mounting in a variety of 6-3/4″ and 6-1/2″ openings.
Check Stock

Pops Sticky Adhesive Replacement for Car Mount, Volport 6 Pack 3M Dots VHB Sticker Pads Double Sided Tape for Socket Base and Magnetic Dashboard Cell Phone Holder with 2 Pack Round Metal Plate Discs

  • ... tapes high temperature resistant, no problem in hot/heat/warmth summer in florida. With this backup stickies adhesion replacement parts, you can replace and reattach phone socket wall mount and magnetic vehicle/truck/uber mount..
  • HOW TO USE 3M VHB ADHESIVE PAD: 1. Remove the used adhesive and clean up the mounting surface with alcohol pad if you have.
  • 2. Peel off the yellow backing film, stick adhesive to the back of mount and press firmly for 3 to 5 minutes for better connecting to the car mount base.
  • 3. Peel off the red backing film, stick on the flat and clean surface you want, then wait 24 HOURS to use after stuck, that’s it..
  • TIPS for USING 3M STICKY ADHESIVE: 1.If the red backing film hard to peel off and the black gel come up with, please repeat this act: peel-if come up-press red film back-peel again. 2.Do not stick adhesive on rugged, texture silicone surface, it may not stick well, clean flat and hard surface will be better. 3. Last but the most important point, please WAIT 24 HOURS after stuck..
  • 2PCS EXTRA METAL PLATES: Extras tiny metal discs can be use inside of phone socket cap to work with magnetic car phone mount, also can be pasted on cell phone or mobile phone case to works with magnetic car holder. Note: 1. Please stick meta....
Check Stock

TAGVO Phone Ring Holder Finger Ring Kickstand and 3M Sticky Adhesive Replacement Set Including Metal Plates - 360°Rotation Metal Grip Holder for Magnetic Car Mount Compatible with Cell Phone

  • 【Metal Plate with Strong Adhesive】Super thin metal plate is designed to use with magnetic mobile phone car mount, magnetic air vent mount and other magnetic cellphone car mount. 1, Advanced surface treatment. 2, Storng adhesive on the back. 3, Scratch-Resistant Protective Films Included, simply stick magnet sticker for phone mount behind films to your case/battery cover, on a rugged case, or directly to your device. Then device will automatically suck as it closes to the car mount..
  • 【3M sticky adhesive replacements compatible with Phone Holder, Metal Plates, Magnetic Car Mount Holder】IMPORTANT NOTE: Here are some problem customer may encountered frequently. 1. Hard to peel off the red backing film, in this situation, please repeat this act: peel-if come up-press red film back-peel again. 2. Adhesive can’t stick well on phone case, please don’t not stick adhesion on rugged, texture surface silicone phone case, it may not stick well. 3. Last but the most important rule, wait.
  • 【Easy to use】You need to remove the used 3M tape of phone car mount and clean up the mounting surface with alcohol pad included until fully dry before installation, then place a new 3M adhesive sticky circles on the back of grip mount or phone case and pres....
Check Stock

2 Kicker 43DSC69304 DSC6930 6x9 Car Speakers+2 43DSC3504 DSC350 3.5' Speakers

  • Package Includes: (1) Pair of Kicker 43DSC69304 6x9 360 Watt 3-Way Car Audio Speakers. (1) Pair of Kicker 43DSC3504 3.5" 80 Watt 2-Way Car Stereo Speakers..
  • Pair Kicker 43DSC69304 DSC6930 6x9 360 Watt 3-Way Car audio Speakers 4-Ohm. Peak: 720 Watts per pair / 360 Watts each. RMS: 180 Watts per pair / 90 Watts each.
  • Recommended Power Range: 6 - 90 watts RMS per channel. Thin-Profile. Zero-to-Minimal Tweeter Protrusion. Polypropylene midwoofer. Acoustic-foam surround. 1/2" Polyethylene-Naphthalate Dome Tweeter.
  • Stamped steel basket. EVC (Extended Voice Coil) technology, for excellent sound - even with a factory radio. Neodymium Tweeter magnet. Grilles included. 4 ohms impedance.
  • Frequency Response: 30-20,000 Hz. Top-mount Depth: 3-1/4". Mounting Diameter: 5-5/8 x 8-7/16". Sensitivity: 92dB. Item Weight: 8.9 lbs.
Check Stock

Pop-Tech 3M Adhesive Sticker Tapes Accessories Pack Replacement Kit for Magnetic Phone Car Mount and Pop Grip Mount Base, Includes Rectangle Metal Plate and Round Magic Plate, Clear Protective Films

  • ...phone without leaving any residue. Remember to apply the protective film on the back of your device before sticking the metal plate.
  • 1 pair of round adhesive sticker replacement for your mount metal plate. Make the car mount plate reusable. 2 piece of alcohol prep pads sent as a GIFT to help you to take care of the surface where you attach your magnetic car mount. You may use the alcohol pad to clean the mounting surface for better result.
  • This set of universal accessories pack is exclusively designed for magnetic car mount and includes everything you need to work with magnet mount. Great replacement car mount accessories pack to extend the service life of your magnetic car mount.
Check Stock

Qubed Compiled by Hans Dunkelkammer

  • VERSATILE MULTI-CHANNEL POWER AMPLIFIER: The S4-100 is a high efficiency multi-channel class D amplifier car audio buffs love for daily driver and....
  • Easy Install, even for Dummies: Set screw terminals connect easily to 4 AWG power/ground wire, and 10 AWGspeaker wire. Surface-mount feet make....
  • NO ELECTRICAL UPGRADES NEEDED: The S4-100 is the perfectmulti channel ampto power a basic “door-swap” upgrade.With a full-range frequency response....
  • Adjustable Crossovers for fine tuning:Sending the wrong frequencies to a speaker can cause poor sound quality and damage speakers. To avoid this,....
  • Our Longevity is Your Advantage: Established in 2002 as Audioque (AQ), we have nearly 20 years of innovation behind our products. We focus on getting....
Check Stock

TORRTOWAY Military Grade Drop Samsung Galaxy Note 9 Case Shockproof with Kickstand Stand Built-in Magnetic Car Mount Armor Protective Case for Galaxy Note 9 Phone Case (Silver)

  • [Compatible Model] Compatible with Samsung Galaxy Note 9. Case for Samsung Galaxy Note 9 [Notice:Not include Magnetic Car Mount Holder].Please Confirm Before Purchasing..
  • [Built-in Foldable Kickstand] Built-In Hide Kickstand:Designed with a built-in kickstand for video calls, watching videos/movies.free your hands.Drop-proof, shockproof and dust-proof,extremely strong protection..
  • [Metal Magnetic Sheet] Built-in metal magnetic sheet, can stably adsorbed to the Magnetic Car Mount holder directly.It is convenient for you to navigate the route when driving..
  • [Precise Cutouts] Precise Cutouts Provide You with Easy Access To All Ports, Speakers, Camera, Buttons and Other Features.Military Grade Drop Test standards,Metal painted surface. Excellent for Outdoor Activities..
  • [Service] We provide premium and 6 months Money Back Guarantee. If you order wrong size or have other question,please feel free to contact us..
Check Stock

MU-CN 12 PCS Replacement Adhesive Stickers for Pop Phone Stand Mount Double Sided Adhesive Pads Circle Sticky Compatible with POP Out Phone Collapsible Grip & Stand/Car Magnetic Phone Mount Holder etc

  • ...esive exclusively designed for grip holder back and various magnetic cell phone car phone mount base. This adhesive replacement kit is a good choice to remount your phone wall mount and magnetic phone mount. With your adhesive cell phone holder, you can position the phone anywhere there’s a flat and hard surface in the car dashboard.
  • Strong 3M Sticky Adhesives: With this car mount replacement parts, you do not worry about purchasing another grip mount. Just remount your expanding stand with this vhb 3m double sided adhesive pads. Best sticker replacement pads for your phone adhesive mount.
  • For best result, please make sure the mounting surface and base of mount adhesive clear cleaned completely before attaching a new 3m adhesive stickers. As for the 3m adhesive tapes, if you find the phone holder adhesive hard to peel, please try to press it back and peel again.
  • Easy to use: You need to remove the used 3m tape of phone car mount and clean up the mounting surface with alcohol pad included until fully dry before installation, then place a new 3m adhesive sticky circles on the back of grip mount and press firmly for 5 to 10 minutes for better connecting to the car mount base. please wait 24 HOURS to use after stuck.
Check Stock