Top Taper Reamer With Pilot

1 7/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56080P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 2" flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 5/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56078P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 7/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

5/8 Bridge Reamer Bridge/Construction Reamer 1/2 Shank M2 HSS Taper Chucking Reamer Bit Tool for Steel Metal Alloy Wood Plastic Drilling Hole

  • Material: 5/8 bridge reamer is made of high-quality M2 HSS steel, with high toughness, high-temperature resistance, corrosion resistance and long service life. Compared to other commonly used low-grade high-speed steels, M2 has an increased content of tungsten and molybdenum, both key elements for improved durability.
  • Wide Application: HSS bridge reamers can enlarge or align existing holes and are suitable for various materials such as aluminum, brass, bronze, cast iron, copper, iron, metal, nickel, plastic, steel and other structural materials Note: It requires existing holes Or a pilot hole is required.
  • Size Infor: Length of chucking reamer is 6.5 inch.
  • Safe to Use: Designed with helical flutes and safety stops to keep chips away from the operator. The safety collar stops to prevent over-penetration and loss of operator stability.
  • Design: The tapered tip design allows the reamer to fit into unevenly overlapping holes, aligning the bolt holes. The 5/8" bridge reamer is not a drill, it just aligns the reamer with the pre-drilled hole.
Check Stock

1/16 HIGH Speed Steel Straight Flute Taper Pipe Reamer

  • Package Included: 2pcs x Morse Taper Reamers.
Check Stock

5/8 Drill Bridge/Construction Reamer with 1/2 Shank Chuck,HSS Taper Bridge Reamer Bit Tool for Steel Metal Wood Alloy to Align Existing Hole and Enlarge Hole

  • The heavy duty high-speed steel bridge reamer is also called construction reamers,it used for aligning an existing hole and enlarging undersized hole prior to bolt or rivet installation.Our reamer bit aligns and enlarges pre-drilled holes ready for bolting..
  • Makes reaming holes out extremely easier than using large drill bits,the reamed hole is smooth without tear-outs. But there must be a existing hole or a pilot hole that is smaller than 5/8" before using our 5/8" Bridge/Construction Reamer..
  • The tapered point design permits the reamer bit to enter into the overlapping holes of out-of-line,make the bolt holes line up.Enlarging the holes in the steering knuckles and pitman arm..
  • The 5/8" bridge reamer bit is not a drill bit,only aligning reamer to aligh holes which are pre-drilled.If you need to expand a hole to 5/8". At first there must be a 3/8" pre-drilled hole,then ream out to 5/8"..
  • Commonly used in bridge,construction,steel erection and automotive truck trailer industries,specially use in structural materials such as steel, metal, alloy aluminum,brass,plastic,iron,nickel,copper,cast iron etc.Three symmetrically placed flats on shank provide positive grip in portable electric and pneumatic tools..
Check Stock

Pointer Knob, 1-1/8, 1/4X1/2 PH, 8-32 SS

  • Made from alloy steel 5155 with heat treat to RC 56-58.
  • Head Diameter?0.747" Head Angle ?15° Drawbar Thread Size?5/8"-11 Machine Taper Size ?CAT40 Neck Diameter?0.549" Hole?0.281" Pilot?0.641" Overall Length?2.001" Shoulder To Head?0.787" Shoulder To End?1.024".
  • High quality black oxide finish to ensure long enduring tool life.
  • Each retention knob is individually magnetic particle tested to ensure free of crack.
  • Fully ground on all critical surface including a pilot under the flange of retention knob for full contact between tool holder's taper end and retention knob.
Check Stock

Lichamp Reamers Set for Metal Taper Reamer Drill Bit for Steel for 3/8 1/2 5/8 3/4 inches Hole M2 HSS Chucking Bridge Steel Reamers

  • Unique Tapered Reamer - Construction grade reamer set are used to align existing holes prior to bolt or rivet installation. Increased taper for ease in hole entry, especially for drilling holes bigger in pitman arm and steering knuckles..
  • M2 High Speed Steel - HSS M2 ensures sharp and fast execution in most hard steel material for clean results, while provides good wear resistance in mild steels and non-ferrous materials..
  • Wide Applications - Works well in free cutting and carbon steels, as well as soft, non-ferrous materials such as aluminum, brass and copper..
  • Five Grooves Fast Drilling - Reversed spiral push chips forward and are ideal for through-hole applications, reduces the friction, runs cooler, performs well in heat, corrosion and rust resistance..
  • Safe Straight Shank - Round shank with 3 flats to prevent slipping in the drill chuck, safety flange/ stop collar to prevent the reamer running through the hole..
Check Stock

Yakamoz 5Pcs Taper Drill Countersink Set 1/4 Hex Shank Countersinks with Tapered Point Pilot Drill Bits for Woodworking

  • Quick change 1/4" hex shank for power drill, 7/64", 9/64", 11/64", 3/16", 7/32" HSS taper drill bits ideal for installing screws..
  • Use these countersinks to drill the pilot hole and countersink hole in one step..
  • 4-Flute cutter countersink and tapered drill bit provide superior speed and ideal finish..
  • Adjustable countersink along taper drill to get proper pilot hole depth for different length screws..
  • Made of High Speed Steel (HSS) drill bits with alloy steel countersinks, good cutting performance on hardwoods and composites and long life use..
Check Stock

YaeKoo 2 pcs Tapered Reamer T Handle 6 Fluted Chamfer Bridge Pin Hole Hand Held Reamer Sizes 1/8\-1/2\ (3-13mm) & 5''-5/8'' (5-16mm) Handle Drilling Tools

  • The Tapered Reamer is used to remove burrs from steel, brass, aluminum, plastic, wood and wall panels.
  • The T Reamers are Precisely machined cutting edges smooth the surface of the metal without effort.
  • Reamer T handle for easy reaming.The removable handle facilitates compact storage..
  • Material of Taper Reamers: high carbon steel heat treatment, longer service life.
  • Packing includes :2 pieces Bridge Pin Hole Reamers, 1/8" -1/2 "(3-13mm) size and 1/5" -5/8 "(5mm -16mm) size.
Check Stock

Pro Fresh Citrus Reamer

  • Premium materials: High quality steel manufacturing, high hardness, high durability. Its taper is 1:10, its structure is stable, and its performance is excellent..
  • Stable structure: It is designed with a 1:10 reamer structure and uses a cutting edge. It has high cutting capacity and high precision, which can be reliably stable in use..
  • Exquisite processes: It meets quality control standards, manufacturing advanced technology, achieving high quality and good performance..
  • Long-term service life: Equipped with cutting edges, high cutting capacity, high precision, long service life..
  • Uses: For reaming mold processing and manual processing..
Check Stock

RLECS 1/8-1/2 (3-13mm) T Handle Tapered Reamer Tool, 6 Fluted Bridge Pin Hole Reamer Tapered Woodworker Cutting Tool

  • Material: High carbon steel, bearing steel.
  • Expanding holes: Ideal for drills to break sheet metal, aluminum plate, plastic and other materials effortlessly..
  • The T-shaped handle provides leverage, making reaming easier, stronger control, and easier turning..
  • Deburring: Suitable for taper holes and chamfering on wooden boards to remove burrs and facilitate screw sinking..
Check Stock

PAGOW T Handle Taper Reamer, 5-16mm Tapered 6 Hand Held Fluted Chamfer Reaming, Repairman's Bridge Pin Hole Reamer Woodworker Cutting Tools

  • Material: Made of hardened ball bearing steel (#9027) with precision ground cutting edges..
  • Tapered Reamer Diameter:1/8"-1/2"(3-13mm).
  • T-Handle Grip: Provides greater leverage and easier reaming. Provides leverage for easier operation and rotation,saving effort. Removable handle for compact storage..
  • Perfect tool kit for every DIY users to enlarge holes in wood. Suitable for reaming taper holes on wooden boards,chamfering,deburring,easy to screw counterbore..
  • Precision machined cutting edges smooth metal surfaces with little effort. Useful tool for removing burrs from steel, brass, aluminum, plastic, wood and wallboard..
Check Stock