Top Terminals For Circuit Board

ALITOVE 16.4ft 5050 SMD Red LED Flexible Strip Ribbon Light 5M 300 LEDs Waterproof IP65 DC 12V for Home Garden Commercial Area Lighting

  • ...end it to right or acute angle, otherwise the circuit board and silicone coating will crack. The strip lights can be cut between every 3 LEDs along along the cutting marks to fit for your project, great for DIY..
  • 【Two different power input ends】One end has 2pin wire, you can screw it to the positive and negative terminals of 12V power supply. The other end has 5.5x2.1mm female DC connector. If your 12V power supply has 5.5x2.1mm male DC connector, just plug and work. The power supply is not included..
  • 【Indoor and Outdoor Use】The LED strip is coated with clear silicone, up to IP65 waterproof rate. It can be used to beautify both indoor and outdoor lighting scenes, such as backyard, deck, boat, living room, bedroom, kitchen, ceiling, stairs etc. 24 months free warranty. We always stand behind our products..
Check Stock

Universal Compact Bench Power Supply- 30 Amp Regulated Home Lab Benchtop AC-to-DC Converter 13.8 Volt Cooling Fan Screw Type Terminals - Jesverty SPS-30II

  • 【Voltage Control】The output voltage is continuously adjustable from 9V to 15V or set at a fixed 13.8V. The Noise Offset Circuit moves unwanted switching noise to another frequency..
  • 【Screw-type main terminals】The main output terminals ensure easy compatibility with all DC-powered devices and are large enough to provide an efficient power transfer to your equipment..
  • 【Auxiliary Output Terminals】2 pairs of auxiliary snap-in terminals and a cigarette lighter socket on the front panel for added convenience..
  • 【Analog V/A Meters】Highly visible V/A twin meters for real-time monitoring of the status..
  • 【Forced Air Cooling Fan & Protection】A built-in cooling fan that prevents overheating and keeps the unit running continuously under heavy loads. Advanced short circuit protection and automatic current limiting ensure the safety of operators and any connected electrical equipment..
Check Stock

EPLZON 8A Manual Reset Push Button Circuit Breaker 125/250V AC 50V DC Thermal Overload Protector with Quick Connect Terminals and Waterproof Button Caps Assortment Kit Pack of 2 pcs

  • ✅ Product Name: Manual Reset Push Button Switch Thermal Circuit Breaker.
  • ✅How it works: This switch can be reset after being disconnected for a period of time, and then press the reset switch again to use it again. When the load exceeds the rated current, the switch reset button will automatically cut off the circuit, thus protecting the circuit..
  • ✅Each package comes with quick connect terminals and the circuit breaker comes with a waterproof button cap. A circuit breaker with a waterproof button cap protects against bad weather. The compact design enables high-density circuit protection configurations..
  • ✅Package List: 2 * Button Type Thermal Circuit Breakers + 2 * Hex Nuts + 2 * Gaskets + 2 * Waterproof Button Caps + 4 * 6.3MM Female Spade Terminals + 4 * 6.3MM Insulation Sleeves.
  • ✅Widely used in household and commercial appliances, small generators, air compressors, automobiles, electric vehicles, power tools, extension cords, industry, transportation, ships, communications, power panels, audio-visual, medical, power supplies, etc..
Check Stock

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check Stock

Crimping Tool for Heat Shrink Connectors,Knoweasy Wire Crimper and Connector Crimper Tool for Insulated Nylon Connectors and Wire Connectors

  • ✅【Crimping Size Range:】The professional insulated wire terminals ratcheting crimper tool is designed for crimp 20-10AWG stranded heat shrink....
  • ✅【Quality Material:】This wire crimper is made of premium industrial grade high strength chrome vanadium steel which is treated with black....
  • ✅【Precise Ratcheting Mechanism:】 Wire connectors are crimped by squeezing the handle through a complete ratcheting cycle until the handle....
  • ✅【Application:】Wire Crimper can be used for home appliance repair, home circuit repair, vehicle circuit connection, and everything about circuit....
  • ✅【After Sales Warranty:】Your customer satisfaction and 12 months warranty of Wire Terminals Crimper can be guaranteed.
Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

EPLZON L1 Series 30A Circuit Breaker Manual Reset Push Button Circuit Breaker 125/250V AC 50V DC Thermal Overload Protector with Quick Connect Terminals and Waterproof Button Caps (Pack of 2 pcs)

  • ✅ Product Name: Manual Reset Push Button Switch Thermal Circuit Breaker.
  • ✅How it works: This switch can be reset after being disconnected for a period of time, and then press the reset switch again to use it again. When the load exceeds the rated current, the switch reset button will automatically cut off the circuit, thus protecting the circuit..
  • ✅Each package comes with quick connect terminals and the circuit breaker comes with a waterproof button cap. A circuit breaker with a waterproof button cap protects against bad weather. The compact design enables high-density circuit protection configurations..
  • ✅Package List: 2 * Button Type Thermal Circuit Breakers + 2 * Hex Nuts + 2 * Gaskets + 2 * Waterproof Button Caps + 4 * 6.3MM Female Spade Terminals + 4 * 6.3MM Insulation Sleeves.
  • ✅Widely used in household and commercial appliances, small generators, air compressors, automobiles, electric vehicles, power tools, extension cords, industry, transportation, ships, communications, power panels, audio-visual, medical, power supplies, etc..
Check Stock

XYGStudy for Raspberry Pi 4B/3B+/3B/2B/B+/A+ Jetson Nano High-Precision AD/DA Expansion Board Sheild Onboard ADS1256 DAC8552 ADC DAC Jumper

  • There’s no AD/DA function on the Raspberry Pi GPIO interface, this may trouble you in the Pi development. However, it won’t be a problem anymore. The High-Precision AD/DA Board allows you to add high-precision AD/DA functions to the Raspberry Pi..
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano.
  • Onboard ADS1256, 8ch 24bit high-precision ADC (4ch differential input), 30ksps sampling rate. Onboard DAC8552, 2ch 16bit high-precision DAC.
  • Onboard input interface via pinheaders, for connecting analog signal. Onboard input/output interface via screw terminals, for connecting analog/digital signal. Features AD/DA detect circuit, easy for signal demonstration.
Check Stock

ALITOVE 16.4ft 5050 Blue LED Flexible Strip Ribbon Light Black PCB DC 12V 5M 300 LEDs Waterproof IP65 for Home Garden Commercial Area Lighting, Without Power Supply

  • ...end it to right or acute angle, otherwise the circuit board and silicone coating will crack. The strip lights can be cut between every 3 LEDs along along the cutting marks to fit for your project, great for DIY..
  • 【Two different power input ends】One end has 2pin wire, you can screw it to the positive and negative terminals of 12V power supply. The other end has 5.5x2.1mm female DC connector. If your 12V power supply has 5.5x2.1mm male DC connector, just plug and work. The power supply is not included..
  • 【Indoor and Outdoor Use】The LED strip is coated with clear silicone, up to IP65 waterproof rate. It can be used to beautify both indoor and outdoor lighting scenes, such as backyard, deck, boat, living room, bedroom, kitchen, ceiling, stairs etc. 24 months free warranty. We always stand behind our products..
Check Stock

Ethernet SmoothStepper Motion Control Board with Smooth Stepper Terminal Board

  • 6 Axis Ethernet SmoothStepper Motion Control Board with Terminals control board.
  • Ethernet SmoothStepper Motion Control Board with Terminals.
Check Stock

Minn Kota Trolling Motor Power Center

  • This battery box / power center contains easy access external battery terminals that allow trolling motor leads and charger leads to be connected to the battery posts without opening the box.
  • Protects your battery (not included) on a small boat, transom application (boats that do not have battery compartments).
  • Built-in, push button battery meter with 4 LEDs displays current “state of charge”.
  • 60A resettable circuit breaker connected to top.
  • 10A resettable circuit breaker connected to two accessory ports.
  • Ring terminals on inside battery connectors.
  • Compatible with group 24 and 27 size batteries.
  • Overall dimensions: 7" x 13.5" wide x 12" tall.
Check Stock

NVX VAD11005 1100W Full Range Class D 5-Channel Car/Marine/Powersports Amplifier with Bass Remote

  • RMS POWER: 【4 ohms: 80W x 4 chan. + 350W x 1 chan.】 【2 ohms: 125W x 4 chan. + 600 x 1 chan.】 【4 ohms bridged: 250W x 2 chan.】.
  • BASS REMOTE: Variable Bass Boost 0 - +18 dB @ 45 Hz. Easily adjust with the included bass remote..
  • MARINE CERTIFIED: Our VAD line includes a conformally coated, marine grade circuit board. This allows this amplifier to be installed in nearly any application..
  • FEATURES: LED indicator lighting | 3-way protection circuitry | Heavy duty aluminum alloy heat-sink | Platinum-plated RCA level inputs | Platinum-plated screw terminals.
Check Stock