Top Thermoplastic Bearing Housings

Tru-Tech FD315T Distributor Rotor

Perfect For Upgrading Stock Hei Distributors For Higher Rpm Fit Small And Big Block Chevy (Except 348 And 409) Housings Are Cnc-Machined 6061-T6 Aluminum With An Upper Support Bearing To Provide Accurate Timing At Higher Rpm.
Distributors Have High Output Coils And Adjustable Vacuum Advances.

Disc brake stopping power for your Ford 9 inch or 8 inch rearend at nearly the same cost as rebuilding/replacing drum brakes.
Kits includes two bolt-on caliper brackets, two 11-1/4" vented rotors, two GM metric style calipers (non-emergency brake), brake pads and hardware for increased stopping power.
Fits over an axle with maximum flange diameter of 6-1/4" O.D..
Rotors have a 2.780" center hole with both 5 on 4-1/2" and 5 on 4-3/4" bolt circles.
Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

This item is for use only with the INFICON Whisper Ultrasonic Leak Detector.
Install the contact probe by twisting it into the tip of the Whisper.
Simply touch the installed contact probe to bearing housings, solenoids, pistons and other mechanical equipment to allow frequencies to travel into the Whsiper's ultrasonic transducer.
Properly functioning machinery sounds smooth and clear, a sharp contrast to malfunctioning machinery.

EASY TO USE: The bushing puller kit cuts down on frustration and expended energy during difficult wheel bearing, suspension bushing, and seal removal and installation repairs.
WIDE RANGE OF USE: The adapter cups with the bearing puller set provide a wide range of options to fit your exact repair needs.
The OEM Tools bushing driver set includes 20 different size cups for versatile use.
ELIMINATE DAMAGE: The metric bushing driver set reduces the possibility of damaging the bearing/suspension housings.
Don’t have to remove components from vehicles with this bushing tools set.
ADAPTABLE: The bushing installer kit comes with an adapter to use bushings with shop press.
Plates and sleeves can be used in a standard workshop press when on-site access isn’t possible.
MORE USES: The bushing tool set works with silent bearings, hydraulic bearings, ball bearings, shaft seals, rubber bearings, and more.
Cups with bushing press and pull kit allow for hundreds of combinations.

Expandable Rollaboard carry on suitcase with easy to access exterior padded tablet sleeve is made of rugged, high density polyester fabric with water....
Strong, telescoping Aircraft grade aluminum handle stops at 38 inches and 42 inches for users of different heights. High performance ball bearing....
Protective reinforced wheel housings, skid guards and molded corner guards protect high wear points. Compression straps for additional security have....
Backed by Travelpro built for a lifetime limited warranty with the trusted companion promise.
Case Dimensions: 21x14x9 inches, Oveall Dimensions: 22.5x14.5x9 inches, Weight: 7.2 pounds.

APPLICATIONS: ideal for filtered effluent service, 1/2 acre pond aeration, commercial ornamental fountains, and large water fountains.
BUILT TO LAST: Franklin Electric submersible motory, heavy-duty 300 V, 10-ft SJOW motor stripped leads, high quality top bearing for maximum....
Hex rubber bearing has extra-large surface for shaft stability and multiple flow channels for keeping particles away from bearing surfaces.
Stainless steel up thrust washer prevents excessive wear in service applications.
non-corrosive thermoplastic discharge and motor brackets.
SPECIFICATIONS: 1/2 HP, 115 Volts, 60 Hz, 10 running Amps, 64.4 staring Amps, 670 Watts, 2-wire, 26 GPM at 50-ft lift.

Expandable Rollaboard carry-on suitcase with easy-to-access exterior padded tablet sleeve is made of rugged, high-density polyester fabric with water repellent coating for greater stain resistance.
Strong, telescoping Aircraft-grade aluminum handle stops at 38" and 42" for users of different heights. High performance ball-bearing wheels deliver a smooth roll..
Protective reinforced wheel housings, skid guards and molded corner guards protect high wear points. Compression straps for additional security have rubberized buckles for comfort. Interior mesh pocket is built into the lid..
Backed by Travelpro built for a lifetime limited warranty with the trusted companion promise..
Case Dimensions: 28x17.5x12, Exterior Dimensions: 29.5 x 17.5x 12.5, Weight: 9.1 lbs.

Expandable Rollaboard carry on suitcase with easy to access exterior padded tablet sleeve is made of rugged, high density polyester fabric with water repellent coating for greater stain resistance.
Strong, telescoping Aircraft grade aluminum handle stops at 38 inches and 42 inches for users of different heights. High performance ball-bearing wheels deliver a smooth roll.
Protective reinforced wheel housings, skid guards and molded corner guards protect high wear points. Compression straps for additional security have rubberized buckles for comfort. Interior mesh pocket is built into the lid.
Backed by Travelpro built for a lifetime limited warranty with the trusted companion promise.
Case Dimensions: 21x14x9 inches, Oveall Dimensions: 22.5×14.5×9 inches, Weight: 7.2 pounds.

Juno trim series 27 is designed for a 6-inch juno housing and has an aperature of 5.75 inches. Perfect when paired with incandescent and LED juno housings.
Airtight and energy Star when paired with select housings - see spec sheet for complete List.
Compatible with IC22, IC22 W, IC22S, IC22R incandescent housings with 5W PAR30, 75 PAR30L or 65W BR30 light bulbs.
Compatible with IC2, TC2, TC2R housings and can be used with 50W PAR30, 75 PAR30L or 65W BR30 Light bulbs.
Compatible with IC22LED, IC22RLED and TC22LED LED housings.

Bracket to be used with 10″ slimline filter housings (fits all brands of housings).
Economical plastic construction is light’weight, yet still very durable.
Housings can be mounted with ports facing to the side or to the front.
Commonly used with drinking water and reverse osmosis systems.

Mounting bracket for Culligan Whole House Sediment Water Filter HF-360 (1653-3325).
The Culligan UB-1 single housing bracket is a “U” shaped mounting bracket for 3/4″ inlet/outlet standard whole house housings..
The UB-1 mounts standard whole house water filter housings and helps support the weight of the water filter..
Screws are included with the UB-1 mounting bracket for securing the water filter housing to the wall. The screws are No.10 1-1/2″ pan head screws..