Top Thread Cutting Oil

uxcell 5/8-18 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 3/8-16 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

1/8 HP Lathe BandSaw Machine Tool Circulation Coolant Pump, Immersion Length 180mm (7\), NPT 1/2\ Thread, Single 1 Phase 110/220V

  • Dark thread cutting oil for lubricating and cooling dies and cutting machines during threading process.
  • Mixture of sulfonated and chlorinated oils for high film strength.
  • Dark formula for high-speed cutting machines.
  • Anti-mist and non-staining for visibility.
Check Stock

uxcell M6 X 1.0 Metric Round Die, Machine Thread Left Hand Threading Die, Alloy Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 1/2-20 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

RIDGID 10883 Model 418 Oiler with Premium Thread Cutting Oil, Silver

  • ALL WEATHER PIPE THREADING OILER: Designed to increase productivity with its durable pump assembly and rust-resistant heavy-duty reservoir that won't warp, crack, or leak.
  • INCLUDED CUTTING OIL: Comes with 1 gallon of premium thread cutting oil to pair perfectly with the 1-gallon reservoir capacity.
  • ERGONOMICALLY DESIGNED: Features a 2-finger trigger mechanism and an anti-slip grip to efficiently help reduce user fatigue.
  • EASY AND CONVENIENT: Integral molded body eliminates leaks at the hose-reservoir connection while the fastener-less twist and lock drip pan easily locks in place.
  • HIGH-QUALITY CONSTRUCTION: Lightweight material that withstands abrasion, won't rust, and is so strong that under typical use, no dents will form on impact and no shape changes will occur over time.
Check Stock

uxcell M16 X 1.5 Metric Round Die, Machine Thread Right Hand Threading Die, Alloy Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 1/2-13 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell M2.5 x 0.45 Metric Round Die, Machine Thread Left Hand Threading Die, Alloy Steel

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell M8x1.25mm Straight 4 Flutes Metric Bottoming Taper Hand Taps 3pcs

  • Tap Size: M12 x 0.5 metric thread, H2 thread tolerance grade, left hand thread cutting. Straight flute design, downward chip removal, clear threads, fast tapping with accuracy..
  • Material and Finish: High speed steel tool is with high hardness and toughness, heat resistance and wear resistance. Features the base substrate without any coatings. Good for general purpose thread tapping..
  • Applications: Suitable for processing through holes. Great for drilling and tapping aluminum, die steel, stainless steel, bronze, hard plastics, etc..
  • Easy to Use: Used on drilling machines, tapping machines, CNC and milling machines. Use with tapping oil to get higher quality threads and more durable taps..
  • Tips: Machine taps are suggested to be used with tap collets with overload protection. Hand use is easy to cause breakage to the tap due to uneven force..
Check Stock

uxcell Metric Machine Tap M3 Thread 0.5 Pitch H2 3 Flutes Hex Shank High Speed Steel

  • Tap Size: M2 x 0.4 metric thread, H2 thread tolerance grade, left hand thread cutting. Straight flute design, downward chip removal, clear threads, fast tapping with accuracy..
  • Material and Finish: High speed steel tool is with high hardness and toughness, heat resistance and wear resistance. Features the base substrate without any coatings. Good for general purpose thread tapping..
  • Applications: Suitable for processing through holes. Great for drilling and tapping aluminum, die steel, stainless steel, bronze, hard plastics, etc..
  • Easy to Use: Used on drilling machines, tapping machines, CNC and milling machines. Use with tapping oil to get higher quality threads and more durable taps..
  • Tips: Machine taps are suggested to be used with tap collets with overload protection. Hand use is easy to cause breakage to the tap due to uneven force..
Check Stock

uxcell 1/4-28 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel, 2pcs

  • ..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock