Top Threaded Anchor Cap
Sleeve Anchor 3/8-Inch by 1-7/8-Inch - Hex Head Sleeve Anchors Concrete Bolts Concrete Sleeve Anchors 100
- CONCRETE BOLTS SLEEVE ANCHORS Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body and integral expander, nut and washer.
- HEAVY DUTY SLEEVE ANCHORS made of plated Carbon Steel.
- CONCRETE SLEEVE ANCHORS Anchors should be installed with carbide tipped hammer drill bits or any other concrete drilling type bits.
- CONCRETE SLEEVE ANCHOR Perfect for mounting to concrete or block.
- SIZE: The diameter of the anchor is 3/8". The length of the anchor is 1-7/8".
Check StockSleeve Anchor 5/16-Inch by 2-1/2-Inch - Hex Head Sleeve Anchors Concrete Bolts Concrete Sleeve Anchors 100
- CONCRETE BOLTS SLEEVE ANCHORS Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body and integral expander, nut and washer.
- HEAVY DUTY SLEEVE ANCHORS made of plated Carbon Steel.
- CONCRETE SLEEVE ANCHORS Anchors should be installed with carbide tipped hammer drill bits or any other concrete drilling type bits.
- CONCRETE SLEEVE ANCHOR Perfect for mounting to concrete or block.
- SIZE: The diameter of the anchor is 5/16". The length of the anchor is 2-1/2".
Check StockThe RidgePro Roof Anchor, Roofing Tool, Roof Hook for First Man Up (FMU) Last Man Down (LMD) The Ridge Pro Newer Version (No Pole)
- This is the Newer Version that uses the non-threaded Sherlock RO57 Pole (Not Included) found at most paint and box stores. Remove the threaded tip on the pole, slide on to the RidgePro and insert the included locking pin. Also sold on Amazon, search for RidgePro Roof Anchor Pole.
- Use as a temporary or permanent fixed-point Roof Anchor, First Man Up (FMU) Safety Device.
- High-Grade, Light Weight Aluminum Construction with built-in stainless-steel shackle harness and rope receiver.
- Features Adjustable Pitch-Selection Grid & Incremental Range, Adjusting from 6/12 - 12/12 Roof Pitches.
- Delivered Securely With Adult Signature Required Upon Delivery.
Check StockForbidden Body Jewelry 14g Surgical Steel 5mm Synthetic Stone Dermal Top Amethyst Single
- Our Synthetic Stone dermal jewelry is made with authentic looking faux "gemstones" set in 316L Surgical Steel.
- These dermal tops are designed to fit a 14 gauge internally threaded anchor.
- they will also fit with any of Forbidden Body Jewelry's anchors. Choose....
- Measurements: 14 gauge threaded bar, 5mm top diameter.
Check Stock10Pcs M8 x 250mm 304 Stainless Steel Fully Threaded Rods, Threaded Rods Bar Studs, Right Hand Thread Long Threaded Screw, M8-1.25 Thread Pitch, Fits for Anchor Bolts, Hangers, U-Bolts (5/16\ x 10\)
- 【Quality Material】These m8 threaded rod made of 304 stainless steel, which provides excellent corrosion resistance and anti-rust ability for long service life.
- 【Package Content】You will get valued 10 pack of 8mm x 250mm threaded rods.
- The fully threaded rods & studs can be drilled, cut, heated and shaped.
- 【All Threaded Rods】Our stainless steel thread rod can be used for assembly fastening, screw into threaded nuts or tapped holes, cut to your desired length.
- 【Wide Application】These 5/16 x 10 inches threaded rods are suitable for a wide variety of applications, such as anchor bolt, clamps, hangers, U-bolts, weld projections, even model building and more projects.
Check StockARES 71502 - Spill Proof Coolant Filling Kit - Eliminates Trapped Air Pockets and Squeaky Belts Due to Overflow
- SPECIFICATIONS: This Coolant Filling kit includes the following: a funnel, a fluid stopper, a threaded cap adapter with gasket for GM, a threaded cap adapter with gasket for Ford, a small cap, a medium cap, a large cap, a 5-inch straight extension, two 2 1/4-inch 45 degree elbows, and two clear tubes..
- DESIGN CONSIDERATIONS: Our Coolant Filling Kit allows you to easily refill automotive cooling systems without having to worry about spilling, which could lead to squeaky belts and trapped air pockets that can impact performance. The stopper helps prevent an excessive pressure build-up during filling, while the extension and elbows allow you to work in hard to reach places..
- APPLICATIONS: This coolant filling set works with radiators and surge tanks on most domestic and imported vehicles. It even includes two threaded cap adapters with gaskets specifically for GM and Ford vehicles, so this set has you fully covered..
- RELIABLE | EFFECTIVE | EFFICIENT: Users trust ARES to be quality tools. You are backed by our Performance Assurance Limited Lifetime Warranty. If you have any issues with your ARES Coolant Filling Kit, simply contact customer service for troubleshooting help, parts, replacement, or refund..
- ASPCA BUSINESS AMBASSADOR: We are proud to be par....
Check Stock3/8\ x 2 1/2\ Lag Screw Expansion Shield Long Zinc Alloy Pk 300
- Expansion shield anchor works with a lag screw to provide a secure hold in most materials including solid masonry, masonry joints, and uncracked concrete.
- Anchor has an internally threaded body made of zamac alloy.
- Meets Fed. Spec. GSA FFS-325C Group 2, Type 1, Class 2C specifications.
- Ultimate tensile strength 420 lb. in 2,000-psi concrete.
- Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations).
Check StockBoltHold - SP12-38 Zinc Plated Steel Asphalt Anchor (5/8\ x 12\) - with 1\ Hex Bolt & Washer - Chemical Anchors - for Installation of Sheds, Carports, Bike Racks, & More - 2000 lb Pull Rated - 6 PK
- Machine Screw Anchors For Concrete You will receive only Machine Screw Anchors when you place a order on this page. The setting tool and sidewalk bolts are not included..
- Using a ½" Combination Drill Bit, drill a hole deep enough to insert a 1/4-20 Machine Screw Anchor into the Concrete or Concrete Block. Blow-out any excess dust in the hole. Insert a ¼-20 Machine Screw Anchor with the threaded cone end portion entering the concrete first..
- Insert a ¼" Setting Tool into the lead portion of the Anchor and strike the Setting Tool with a hammer until the lip of the setting tool meets the top of the Machine Screw Anchor. Your Anchor is now ready for use with ¼-20 Bolts..
- Please do all your research before ordering. Make sure you are comfortable on the installation process before you order. Returns are subject to a 15% or more restocking fee depending on return condition..
Check StockTEACH Flat Head Phillips Drive Concrete Screw to Anchor Masonry, Block & Brick,270-Piece
- Concrete Screw Flange 5/8" Head (depending on the length, it will be either full or partial threaded). The diamond tip allows for superior penetriating into hard materials. Great for anchoring items to concrete, brick, block, or other masonry materials. Ceramic coating exceeds 500/hrs salt spray resistance.
- An externally threaded, hardened screw with a double lead, consisting of alternating raised and lowered threads with notches cut into the raised threads, and a diamond-shaped, nail-type point. Cuts its own threads and when used in concrete, block or brick. Eliminates the need for an anchor when used in light or medium-duty applications. When used in concrete, it can be removed and re-driven into the same hole. Special carbide bits are recommended for driving concrete screws into masonry..
- Some applications include anchoring the following to masonry: electrical junction boxes, wooden beams, plywood, exterior insulation, metal flashing, thresholds. Hole should be of a depth equal to the required embedment plus 1/2”.
- Concrete screws should be installed a minimum of ten anchor diameters between each other. They have an advantage over most other types of masonry anchors in that they can be installed close to the edge of t....
Check StockConcrete Sleeve Anchors 1/2 x 4 - 25 Pcs Hex Head Sleeve Anchors Concrete Bolts Hex Nut Sleeve Anchor Concrete Sleeve Anchor Hex Sleeve Anchors Zinc Plated
- CONCRETE SLEEVE ANCHORS - Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body and integral expander, nut and washer.
- HEAVY DUTY SLEEVE ANCHORS - Steel construction with Zinc-plated finish.
- CONCRETE HEX SLEEVE ANCHORS - This anchor is designed for use in Concrete, Block, and Brick. Ideal for hand rails, window frames, partitions, cabinets, shelves and pipe supports.
- SIZE: The head diameter of the anchor is 1/2". The length of the anchor is 4".
- Package Quantity 25 Pcs Hex Nut Head Concrete Sleeve Anchors.
Check StockMasmoc 10Pack M8 x 80mm Fully Threaded Rod Stud 304 Stainless Steel Threaded Screw Right Hand Threads M8-1.25 Thread Pitch with 20PCS Hex Nuts and 20pcs Washers
- Package :M8 x 80mm right hand full threaded rod 10PCS, M8 hex nuts 20PCS, M8 washer 20PCS..
- Thread rod Dia.: M8, Thread Pitch: 1.25mm,total length: 80mm made of 304 stainless steel, provides great corrosion resistance and anti-rust ability for long service life, thread direction: right-hand thread..
- These threaded rods and studs are fasteners that screw into threaded nuts or tapped holes, allowing for assembly of components..
- These threaded studs can be drilled, cut, heated and shaped and widely applied in many occasions: anchor bolts, clamps, hangers and U-bolts and many more projects..
Check StockOatey 3 in. PVC Backwater Valve
- Protects low areas or basements from backflow or waste from street sewers.
- Elastomeric seal in quick action flapper ensures a water tight seal.
- Threaded access cap incorporates a neoprene seal for positive sealing and can be tightened or removed by hand.
Check Stock